Related Manuals for Chipsee CS12800RA4101P
Summary of Contents for Chipsee CS12800RA4101P
- Page 1 Industrial PC PPC-CM4-101 PN: CS12800RA4101P Content can change at anytime, check our website for latest information of this product. www.chipsee.com...
- Page 2 6.5. WiFi & BT Module 6.6. 3G/4G/LTE Module 6.7. Zigbee Module 7. TF Card Slot 8. Audio Connectors 9. PROG Button 10. Mounting Procedure 11. Mechanical Specifications 11.1. CS12800RA4101P 12. 3D Model 13. Disclaimer 14. Technical Support Chipsee Page 2 of 30...
- Page 3 PPC-CM4-101 PPC-CM4-101 Front View Chipsee Page 3 of 30...
- Page 4 PPC-CM4-101 Rear View Chipsee Page 4 of 30...
- Page 5 PPC-CM4-101 Side View 1 Chipsee Page 5 of 30...
- Page 6 PPC-CM4-101 Embedded PCB Chipsee Page 6 of 30...
- Page 7 Product Overview ® ® The Cortex -A72 Raspberry Pi series PPC-CM4-101 (PN: CS12800RA4101P) is a high-quality industrial Pi PC. It features a 10.1” Ten-point capacitive touch screen with a resolution of 1280 x 800 pixels and brightness of 400 cd/m .
- Page 8 ® The PPC-CM4-101 industrial Pi PC does not include the CM4 Raspberry Pi module by default. If you would like to purchase it with a CM4, you can select it at the Chipsee store during the ordering process. Operating System This product comes with a pre-installed Raspberry Pi OS.
- Page 9 PPC-CM4-101 Optional Features Optional Features The PPC-CM4-101 industrial Pi PC does not include the 3G/4G/LTE modules by default. These modules are optional and can be selected at the Chipsee store during the ordering process. Warning Installation, repair, and maintenance tasks should be performed by trained personnel only.
- Page 10 Onboard Zigbee module, not mounted by default HDMI Not Supported SATA II Not Supported 3G/4G/LTE Supported, not mounted by default Camera Power Input From 12V to 36V Current 800mA Max at 12V Power 9.6W Typical Consumption Chipsee Page 10 of 30...
- Page 11 The default product without the CM4 does not include a Wi-Fi/BT module. You can include a CM4 that has the Wi-Fi/BT module at the Chipsee store during the ordering process. This TF card is designed for storage expansion, as the TF card uses the same pins with WiFi, it can’t be used...
- Page 12 DC Power Positive Terminal Pin 2 Negative Input DC Power Negative Terminal Pin 3 Ground Power System Ground Table 346 Power Connector Note The system ground “G” is connected to power negative “-” on board. Chipsee Page 12 of 30...
- Page 13 Bad GND problems can also be confirmed by touching pin 3 of the Power Input connector with one hand while operating the capacitive touch screen with the other hand. In this case, the operator’s body acts as the Power System Ground. Chipsee Page 13 of 30...
- Page 14 The table below offers more detailed description of every pin and its definition: RS232 / RS485 / CAN Pin Definition: Pin Number Definition Description Pin 1 CAN_H CAN BUS “H” signal Pin 2 CAN_L CAN BUS “L” signal Pin 3 RS485_5- CPU UART5, RS485 –(B) signal Chipsee Page 14 of 30...
- Page 15 Pin 9 RS232_0_RXD CPU UART0, RS232 RXD signal Pin 10 RS232_0_TXD CPU UART0, RS232 TXD signal Pin 11 System Ground Pin 12 System +5V Power Output, No more than 1A Current output Table 347 Connectivity Section Chipsee Page 15 of 30...
- Page 16 5-24V input signal. If your input signal is less than 5V, please change this input resistor. The reduced schematic is for reference purpose, if you need the precise resistor schematic, please contact us. Isolated GPIO reduced schematic Chipsee Page 16 of 30...
- Page 17 OUT3 Isolated Output 3 Pin 7 OUT4 Isolated Output 4 Pin 6 Isolated Input 1 Pin 5 Isolated Input 2 Pin 4 Isolated Input 3 Pin 3 Isolated Input 4 Table 348 GPIO Connector Pin-out Chipsee Page 17 of 30...
- Page 18 Be careful not to touch surrounding electronic components accidentally while plugging in USB devices into the embedded Industrial PC version. Remember to unplug the Type-C cable after flashing OS, otherwise the USB hosts won’t work. Chipsee Page 18 of 30...
- Page 19 These Giga LAN signals come from the CM4 module directly. RJ45 LAN Connector Note Use CAT5 or better cables to achieve full data throughput over maximum distance defined by the 1000BASE-T standard (100m). Chipsee Page 19 of 30...
- Page 20 The default PPC-CM4-101 without the CM4 does not include a Wi-Fi/BT module. If you include a CM4 that has the Wi-Fi/BT module, the product will have Wi-Fi/BT feature. The enclosed (CS12800RA4101P) variant of the product also includes an SMA connector for an external WiFi/BT antenna, as illustrated in the figure below.
- Page 21 Attention The product does not come shipped with the 3G/4G/LTE module by default. If you need to use 3G/4G/LTE, you can contact us when placing an order, we can install the necessary hardware for you. Chipsee Page 21 of 30...
- Page 22 TI CC2531, and the Raspberry Pi forum supports it. For CS12800RA4101P, there is a connector on the backside of the case that you can use to connect the external Zigbee antenna, as described in the figure below. If you need to use WiFi/BT and Zigbee together, we can customized the case and add another SMA connector for you, usually across the rear to the opposite of the current SMA.
- Page 23 PPC-CM4-101 Zigbee Module The product does not come with the Zigbee module by default. Chipsee Page 23 of 30...
- Page 24 This storage extension SD uses the same pins as WiFi on CM4. SD storage and WiFi can’t be used at the same time. The product does not come shipped with the TF card by default. Chipsee Page 24 of 30...
- Page 25 Also, the PPC-CM4-101 industrial Pi PC has a miniature 2W internal speaker for audio reproduction, as well as a small buzzer for alarm/notification sounds. Audio Connector Attention By plugging in the headphone cable, the internal speaker will be disabled automatically. Chipsee Page 25 of 30...
- Page 26 There is no need to press the button during regular operation. However, if you need to reinstall the OS, please refer to the detailed information on how to reflash the OS from the Software Documentation. PROG Button Chipsee Page 26 of 30...
- Page 27 Attention Please make sure the display is not exposed to high pressure when mounting into an enclosure. You can find detailed information about mounting in the Mount IPC Guide. Chipsee Page 27 of 30...
- Page 28 PPC-CM4-101 Mechanical Specifications Panel mounting Mechanical Specifications CS12800RA4101P For CS12800RA4101P, the outer mechanical dimensions are 276 x 194 x 46mm (W x L x H). Chipsee Page 28 of 30...
- Page 29 PPC-CM4-101 3D model can be viewed in the online doc in a web browser, if you are reading from the PDF version, please visit the online doc PPC-CM4-101, select hardware documentation, drag the navigation bar to the 3D Model section. Chipsee Page 29 of 30...
- Page 30 If you cannot find the solution you’re looking for, feel free to contact us. Please email Chipsee Technical Support at support@chipsee.com, providing all relevant information. We value your queries and suggestions and are committed to providing you with the assistance you require.
Need help?
Do you have a question about the CS12800RA4101P and is the answer not in the manual?
Questions and answers