Download Print this page
Flowserve Kammer LinedFlow 132000 User Instructions

Flowserve Kammer LinedFlow 132000 User Instructions

Valves for corrosive applications
Hide thumbs Also See for Kammer LinedFlow 132000:

Advertisement

Quick Links

User Instructions LinedFlow - KMENIM3202-02 01/12
USER INSTRUCTIONS
®
Kämmer
LinedFlow
-
®
Installation
132000
Valves for Corrosive Applications
Operation
Maintenance
FCD KMENIM3202-02 01/12
Experience In Motion
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the Kammer LinedFlow 132000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Flowserve Kammer LinedFlow 132000

  • Page 1 User Instructions LinedFlow - KMENIM3202-02 01/12 USER INSTRUCTIONS ® Kämmer LinedFlow ® ™ Installation 132000 Valves for Corrosive Applications Operation Maintenance FCD KMENIM3202-02 01/12 Experience In Motion...
  • Page 2 ...the piping system and control system must be installed Remove actuator from valve properly and checked regularly. The wall thicknesses of the FLOWSERVE control valves correspond to the standards Install actuator on valve and regulations for the pressure stage requirements of the Disassemble and assemble valve piping system in question.
  • Page 3 – particularly protective clothing. INTENDED USE WaRNINg: Disconnect or loosen the fastners – particularly The series 132000 valves from Flowserve Essen GmbH between bonnet and housing – only after the valve has been STOP! can be installed in all areas endangered by gas explosion, removed.
  • Page 4 User Instructions LinedFlow - KMENIM3202-02 01/12 ® DaNgER: Do not install valves whose approved pressure any recognizable malfunctions before startup. See also and temperature range is not sufficient for the operating applicable sections in maintenance regulations for this valve conditions. The limits for use are marked on the valves. series.
  • Page 5 DIN PN 16 industrial applications. If anything is not clear, particularly if ANSI Class 150 (Flanged) any detailed information on the specific product is missing, clarify as required with the responsible FLOWSERVE repre- Liner thickness 4 – 6 mm sentative. TROUBLESHOOTINg When troubleshooting or during general maintenance, always observe Section 1 “Safety precautions”.
  • Page 6 User Instructions LinedFlow - KMENIM3202-02 01/12 ® Table 3: K Values Plug Valve Size Hastelloy Hastelloy TFM1600 -Values Seat DN15/20 DN25 DN 40 DN 50 DN 80 DN 100 DN 150 Hastelloy TFM1600 TFM1600 Seat ø 0.5"/0.75" 1" 1½" 2" 3"...
  • Page 7 User Instructions LinedFlow - KMENIM3202-02 01/12 ® STEM 17.5 Check packing nut (see Table 8). The valve stem is equipped with a blowout protection fea- caUTION: An excessively tightened gland nut can cause ture. This ensures that the valve stem cannot be removed excessive packing wear and can hinder the free movement from the top of the valve.
  • Page 8 User Instructions LinedFlow - KMENIM3202-02 01/12 ® Actuator stem Coupling Coupling screw Coupling insert Locknut Packing nut Yoke plate Slotted nut Yoke rod nut Plug stem Test connection (drawn rotated 90°) Bonnet bolt Bonnet O-Ring (body/bonnet) Bellows seal Body Insert, thread lock Plug Seat Fig.
  • Page 9 User Instructions LinedFlow - KMENIM3202-02 01/12 ® REMOVINg acTUaTOR FROM VaLVE (See Fig. 1) 18.1 Shut off air supply. DaNgER: Ensure that actuator is not under pressure and drain process medium before performing maintenance work. Failure to observe can lead to serious injuries. 18.2 Remove piping if required.
  • Page 10 User Instructions LinedFlow - KMENIM3202-02 01/12 ® Bellows seal O-Ring Plug Insert, thread lock Seat Body Plug Seal (G¼ only with adapter) Bushing Bonnet Screw Slotted nut Stem Packing Packing follower Packing nut Fig. 2: Individual Parts for Series 132 000 (also see spare parts lists) able 6: Tightening Torque for Seat (Nm) DN 15...
  • Page 11 DISaSSEMBLE VaLVE (see Fig. 2) 20.2.1 Replace all worn or damaged parts. Use only genuine FLOWSERVE parts. Parts to be reused must be clean. DaNgER: As toxic or hazardous substances could be Always replace parts subject to wear such as gaskets, present, release all pressure in the system and drain all packings and O-rings.
  • Page 12 Tel.: +65 6879 8989 Fax: +49 (0)201 8919 662 Fax: +1 412 787 1944 Fax: +65 6862 4940 Your Contact: All data subject to change without notice © 07.2003 Flowserve Corporation. Flowserve and Kämmer are trademarks of Flowserve Corporation flowserve.com...