Download
Share
Print this page
  1. Manuals
  2. Brands
  3. TrolMaster Manuals
  4. Controller
  5. BETA Series
  6. User manual

TrolMaster BETA Series User Manual

Co2 ppm controller
Hide thumbs Also See for BETA Series:
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
CO2 PPM Controller (BETA-8)
OVERVIEW
Thank you for purchasing our BETA-8 CO2 Controller, which is a simple and affordable way to control your
CO2 injection device. Choose your desired CO2 level and the Controller will maintain that specified value. A
built-in photocell on the sensor will deactivate CO2 injection at night. A remote sensor with 16ft long cable
allows close placement to plant canopy.
Night Mode: the Controller will turn off the output of CO2 device.
Day Mode:
a)
lf the Fuzzy Logic function is disabled, the unit will OPEN the output of the CO2 device when the current
CO2 level is below setpoint, and CLOSE the output when the current CO2 level is above the CO2 setpoint
plus deadband value.
b)
lf the FuzzyLogic function is enabled, the unit will fully OPEN the output of CO2 device when the current
CO2 level is much lower than the setpoint. When the CO2 level is close to the setpoint, the unit will
calculate and send PWM signal to control the output of CO2 device, The PWM cycle is 5 seconds.
User Manual
BETA-8
BETA Series -Single Controller
01

Advertisement

loading
Need help?

Need help?

Do you have a question about the BETA Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for TrolMaster BETA Series

Summary of Contents for TrolMaster BETA Series

  • Page 1 CO2 PPM Controller (BETA-8) User Manual BETA-8 BETA Series -Single Controller OVERVIEW Thank you for purchasing our BETA-8 CO2 Controller, which is a simple and affordable way to control your CO2 injection device. Choose your desired CO2 level and the Controller will maintain that specified value. A built-in photocell on the sensor will deactivate CO2 injection at night.

  • Page 2: Installation

    INSTALLATION Mount the Controller on wall, place the sensor in a well ventilated area. ● Connect the CO2 sensor to the Controller. ● Plug the Controller into a 120V NEMA 5-15 wall outlet. ● Program the desired setting before connecting to CO2 generator or regulator. ●...
  • Page 3 OPERATION INSTRUCTIONS 1. Reading CO2 Level a) Warm up the unit for approximately 1 minute. b) After warm-up, the LED will display the current CO2 level (as PPM). c) The CO2 Device LED will turn green when connected with CO2 generator or CO2 regulator. 2.
  • Page 4 3. Minimum CO2 Recorded Value Recall Press button twice, the LED will display the minimum CO2 recorded valueand and the Min LED indicator will be blinking. To clear the record, press button button , all digits on LED will be blinking, press and hold button for 3 second to clear the record.
  • Page 5 4. CO2 PPM Level Setpoint Adjustment The factory setpoint of the CO2 PPM level is 1200 PPM. lf the CO2 level is lower than 1200 PPM, the controller will turn on output relay to drive the CO2 device to enrich the CO2 in the grow area. When the CO2 PPM level exceeds setpoint plus deadband (50PPM), the controller wil cut off the output.
  • Page 6 6.Fuzzy Logic Mode a). Fuzzy Logic mode counters rising or falling CO2 levels by quickly activating the CO2 solenoid valve, allowing CO2 levels to be controlled more precisely. b). The Fuzzy Logic function is active if the Fuzzy Logic LED indicator illuminates.
  • Page 7 7.Calibrating the CO2 Sensor a). Place the sensor outdoors in a shaded area. Do not place in direct sunlight. Keep away from people, animals and other CO2 emitting units. Note: lf calibration will be in a high-traffic area or highly populated area, a slightly higher calibration value of 400-475 ppm is recommended.
  • Page 8 8.Restore the Factory Settings Press and hold button before plugging controller into wall outlet. Power the controller, the LED will display "rESt" and blink. Keep holding the button for 5 seconds until the LED displays "donE".

  • Page 9: Factory Default Settings

    NDlR (Nondispersive Infrared) Package Weight: 0.56Kg Dimensions: 130x78x46mm For any issues or concerns with our products, DO NOT return them to the store. Please contact our tech support department at support@trolmaster.com or call 877-420-9876. June 2024 ©2024 TrolMaster™ All rights reserved.

This manual is also suitable for:

Beta-8