Lelit Anna PL41EM Manual
Also See for Anna:

Advertisement

Lelit Anna PL41EM Manual

USER INSTRUCTIONS

PRODUCT OVERVIEW AND USER INSTRUCTIONS

Starting the machine

  1. Remove the machine from its packaging and make sure all packing parts have been taken off (including the protection bags).
  2. Lay the machine on a flat and steady surface far away from hot places and from the water taps.
  3. Remove the water tank cover (19) placed on the top of the machine and pull the water tank out paying attention not to damage the water tubes inside the tank.
  4. Rinse the water tank accurately with fresh water.
  5. Fill the tank with cold water.
  6. Replace the water tank back in the machine and check that the water tubes are not bent and that the filter is well set on one of them; reposition the tank cover (19).
  7. Place the filterholder (8) under the brewing group (5) and turn it from the left to the right. Leave it there so that it can get warm and it gets ready for use.
  8. Open the steam/hot water knob (4).
  9. Place an empty jug under the steam/hot water wand (6). Press the steam switch (12) and the coffee/hot water switch (13).
  10. Plug in the machine in the mains. Make sure that the wall socket is of the right voltage.
  11. Turn the machine on by pushing the on/off switch (11). The LED light: machine on (14) turns on to confirm the power supply.
  12. When water is delivered from the steam/hot water wand (6), press the coffee/hot water switch (13) and the steam switch (12) again and close the steam/hot water knob (4).
  13. Press the coffee/hot water switch (13) and deliver water from the brewing group (5) for around 2 minutes with the filterholder inserted (8); after that, stop the delivery by pressing the coffee/hot water switch (13). Wait at least 1 minute before proceeding with the next operation.
  14. Fill the tank with cold water.
  15. Open the steam/hot water knob (4).
  16. Press the steam switch (12) and the coffee/hot water switch (13) and deliver water for around 2 minutes; after that stop the delivery by pressing the steam switch (12) and the coffee/hot water switch (13). Close the steam/hot water knob (4).
  17. Wait at least 1 minute before proceeding with the next operation.
  18. After completing all these operations, leave the machine on.

Preparing a coffee

  1. Check that the water tank (1) has been filled in with water by looking at the water level indicator (20).
  2. Press the on/off switch (11): the LED light "machine on" (14) will turn on. Do this operation only if the machine is off. If it's on pass to the following point.
  3. As soon as the indicator light (3) turns on, the machine is ready for use.
  4. Fit the single cup filter (9) or the two-cup filter (10) into the filterholder (8) that has been warmed up by leaving it attached to the brewing group as described in point 7.
  5. Before preparing your coffee, it is advisable to press the coffee/hot water switch (13) to dispense water for 5 seconds from the brewing group (5) with the filterholder inserted (8), into the drip tray. After dispensing water for the indicated time, press the coffee/hot water switch (13) in order to stop the purge.
  6. Fill the filter with the ground coffee by means of the supplied measure spoon (16): 1+1/2 measuring spoonful (16) = 1 coffee cup - 3 measuring spoonful (16) = 2 coffee cups. Every time you fill the filter with a spoonful of coffee, press the coffee with the tamper (15) before proceeding to fill it with the next spoonful, remove any excess coffee from the rim of the filterholder.
  7. Insert the filterholder (8) into the brewing group (5), turn it from left to right with force, then put the cup on the removable water drip tray grate (7).
  8. Press the coffee/hot water switch (13). The pressure value on the manometer (17) should reach the green zone during the extraction.
  9. Once you get the coffee desired quantity, push the coffee/hot water switch (13) again.
  10. Remove the filterholder (8) and throw the coffee grounds away. Make sure that the filterholder is clean and replace it in the brewing group to warm up again.

Preparing a coffee with coffee pods

  1. Check that the water tank (1) has been filled in with water by looking at the water level indicator (20).
  2. Press the on/off switch (11): the LED light "machine on" (14) will turn on. Do this operation only if the machine is off. If it's on, pass to the following point.
  3. As soon as the indicator light machine ready (3) turns on, the machine is ready for use.
  4. Fit the pod filter (18) into the filterholder (8) that has been warmed up by leaving it attached to the brewing group as described in point 7.
  5. Before preparing your coffee, it is advisable to press the coffee/hot water switch (13) to dispense water for 5 seconds from the brewing group (5) with the tightened filterholder (8) into the drip tray. After dispensing water for the indicated time, press the coffee/hot water switch (13) in order to stop the purge.
  6. Open the single packed pod not damaging the pod.
  7. Place the pod in its filter (18).
  8. Insert the filterholder (8) into the brewing group (5), turn it from left to right with force, then put the cup on the removable water drip tray grate (7).
  9. Press the coffee/hot water switch (13). The pressure value on the manometer (17) should reach the green zone during the extraction.
  10. Once you get the coffee desired quantity, push the coffee/hot water switch (13) again.
  11. Remove the filterholder (8) and throw the used pod away.

Steam

  1. Check that the water tank (1) has been filled in with water by looking at the water level indicator (20).
  2. Press the on/off switch (11): the LED light "machine on" (14) will turn on. Do this operation only if the machine is off. If it's on pass to the following point.
  3. Press the steam switch (12).
  4. As soon as the indicator light machine ready (3) turns on, the machine is ready for use.
  5. Open the steam/hot water knob (4). First some water will come out of the wand, then steam.
  6. Put the cup with the desired infusion under the steam /hot water wand (6) and turn the knob completely.
  7. When the drink has been suitably frothed, close the steam/hot water knob (4) and press the steam switch (12) again.

  8. after you have frothed your milk, open the steam/hot water knob (4) again and press the steam switch (12) and the coffee/hot water switch (13) again. When some water flows out of the steam wand (6), close the steam/hot water knob (4) again and press the steam switch (12) and the coffee/hot water switch (13) again at the same time. Clean the steam/hot water wand (6) carefully.

Hot water

  1. Check that the water tank (1) has been filled in with water by looking at the water level indicator (20).
  2. Press the on/off switch (11): the LED light "machine on" (14) will turn on. Do this operation only if the machine is off. If it's on pass to the following point.
  3. As soon as the indicator light machine ready (3) turns on, the machine is ready for use.
  4. Before preparing your drinks, it is advisable to open the steam/hot water knob (4) and press the steam switch (12) and the coffee/hot water switch (13). You will have immediately water coming out of the steam/hot water wand (6). Dispense water into the drip tray for 5 seconds. After that press the coffee/hot water switch (12) and the steam switch (12), then close the steam/hot water knob (4).
  5. Place an empty jug / cup under the steam/hot water wand, open the steam/hot water knob (4) again.
  6. Press the steam switch (12) and the hot coffee/hot water switch (13). Hot water will come out of the steam/hot water wand (6) immediately.
  7. Once you have got the desired quantity of water, repress the steam switch (12) and the coffee/hot water switch (13) again and close the steam/water knob (4).
  8. After obtaining hot water from the steam/hot water wand (6), make sure that there is still water in the tank (1).

USEFUL TIPS

  • The single cup filter (9), the two-cup filter (10), the pod filter (18) and the blind filter (21) do not need to be washed after each use but check that the holes are not clogged.
  • For best results, we suggest warming the cups up on the cup warmer (2) which works only when the machine is on.

CLEANING AND MAINTENANCE

Cleaning and maintenance of the machine are essential for the quality of the coffee and the durability of the appliance.

Cleaning
The machine must be cleaned at least once a week.
Before starting, remove the plug from the electrical outlet and allow the machine to cool.
Use a soft cloth, preferably microfiber, like the LELIT cloth (code PLA9101 - not included), and moisten it with tap water. Do not use any abrasive detergent and do not immerse the machine in water.

For thorough maintenance, we suggest using the LELIT brush (code PLA9101 - not included), which will help you clean the shower and the spaces between the gaskets more effectively, removing stains and coffee residues from even the smallest cracks.
Warm running water can be used to clean the removable parts of the machine. The filters and filterholder should never be washed in dishwasher.
There is no need to clean the filters after each use, but just to ensure they are not clogged.
However, to ensure the best performance from your machine, it is essential to thoroughly clean the steam wand and filterholder after each use.
The filterholder should be cleaned to remove the greasy coffee residues that can negatively affect the taste of your coffee.
Wash the external part of the steam wand with a damp cloth and release a little steam to remove any milk residues from inside the wand, as these could obstruct the steam output, making it more difficult to froth milk properly.

BACKFLUSHING

It is recommended to perform this cleaning at least once a week and / or at least every 100 brewed coffees.
The following instructions apply to all types of groups fitted to all the LELIT coffee machines.

Material needed:

  • Blind filter (21)
  • Brush (code PLA9101)
  • Detergent powder for coffee machine (code PLA9201)

Group cleaning. Follow these steps:

  1. Place the blind filter (21) in the filterholder
  2. Add 1 single-dose bag of detergent powder (3,5 grams) in the blind filter
  3. Insert the filterholder into the brewing group
  4. Switch the coffee switch on for about 10 seconds
  5. Stop the coffee brewing and wait for 10 seconds
  6. Repeat this operation 5 times without removing the filterholder
  7. Remove the filterholder, switch the coffee switch on again and rinse the filterholder under hot water that will be dispensed from the group. Turn the switch off
  8. Clean the brewing group and the filter first with the brush and then with a damp cloth in order to remove all coffee residues
  9. Insert the filterholder into the brewing group again and repeat points 4-5-6 without detergent powder
  10. Throw away the first coffee you'll brew

Cleaning of the accessories through immersion. Follow these steps:

  1. Place the filters and filterholder in a jug with the filterholder handle upwards
  2. Pour 2 single-dose bags of detergent powder in the jug (7 grams)
  3. Pour 1 liter of hot water in the jug until the metallic part of the filterholder is completely immerged
  4. Wait at least 15 minutes
  5. Remove the immerged parts and rinse them with plenty of warm tap water
  6. Throw away the first coffee you'll brew

MACHINE DESCALING

Use of the machine creates a natural formation of limescale, over a time period depending on how frequently the machine is used and on the hardness of the water.
Limescale deposits can obstruct the tubes and decrease the brewing temperature, altering the quality of the coffee and reducing the lifetime of your machine.

To avoid the formation of limescale, which can also deposit in the internal circuits, we recommend the use of our LELIT resin filter (code PLA930M - not included) to soften the water. Please insert the water softener filter in the tank following the instructions on the packaging. The filter purifies the water from the calcium and magnesium salts which are deposited to form limescale and affect the taste of your coffee. Remember that the filter loses its efficacy after a certain amount of water treated, so replace it periodically. Instructions for the use and replacement of the filter are given on the box.
To avoid any possibility of damaging of the machine's components, ADD ONLY NATURAL DESCALING PRODUCTS INTO THE WATER TANK.

TECNICAL DATA

Voltage: 220-240V 50Hz; Power: 1050W
Heating time: ca. 3 min.; Pump pressure: 15 bar
Water tank: 2,7 litres
Dimensions (HxLxD): 34*23*27 cm
Weight: 9 kg

To be operated with ground coffee and coffee pods
PL41EM-120: 120V - 60Hz; power 1050W
PL41EM-AS 220V 60Hz; power 950W

TROUBLESHOOTING

We thank you for buying one of our products, designed and assembled in compliance with the most up-to date technological innovations.
Following the simple operations described in this manual carefully, which complies with all essential safety regulations, you will get the best performance and will appreciate the remarkable reliability of this product over the years.
Please find below the description of the most frequent problems and their solution:

PROBLEM CAUSE SOLUTION

There is no crema on the coffee surface

  1. Coffee blend not suitable for machine
  2. Improper grinding
  3. Too little coffee in filter; the pressure indicated by the manometer (17) is under 8 bar
  4. The filterholder has not be tightened under the brewing group
  1. Use a different coffee blend
  2. Adjust coffee grinding
  3. Put more coffee in the filter and press it properly
  4. Tighten the filterholder better

The coffee is too cold

  1. The machine had not reached the proper temperature
  2. Filterholder has not been preheated
  3. Cups have not been preheated
  4. Thermostat malfunction.
  1. See section "Starting the Machine" and "Preparing a coffee"
  2. Filterholder must be heated together with the water – see section "Starting the Machine"
  3. Properly heat the cups on the cupwarmer (2)
  4. Contact the nearest SERVICE CENTER

The coffee is delivered too quickly

  1. Coffee too coarsely ground
  2. Too little coffee in the filter
  3. Coffee has not been pressed enough
  4. Coffee/pod old or unsuitable
  1. Use a finer grinding
  2. Put more coffee in the filter
  3. Press the coffee more firmly
  4. Use a different coffee blend
Coffee comes out between the coffee group and the filterholder
  1. Filterholder not properly inserted
  2. Too much coffee in the filter
  3. Edge of the filterholder not clean
  4. The brewing group gasket is worn or damaged
  1. Insert the filterholder correctly
  2. Put less coffee in the filter
  3. Clean the edge of the filterholder and the brewing group gasket
  4. Contact the nearest SERVICE CENTER

Coffee is delivered in drops

  1. Coffee too finely ground
  2. Too much coffee in the filter
  3. Coffee too firmly pressed
  1. Use a coarser grinding
  2. Put less coffee in the filter
  3. Press the coffee more gently

The machine does not produce steam

  1. The steam/hot water wand hole may be obstructed
  2. Lack of water in the tank
  3. The steam/hot water wand has been improperly positioned
  1. Clean the hole with a needle
  2. See section "Starting the Machine"
  3. Reposition the steam/hot water wand
No coffee produced during the coffee shot; the manometer indicates 0 bar pressure
  1. Lack of water in the tank
  2. Steam switch on
  1. Fill the tank
  2. Turn the steam switch off
No coffee produced during the coffee shot; the manometer indicates more than 14 bar pressure
  1. Coffee too finely ground
  2. Too much coffee in the filter
  3. Coffee too firmly pressed
  4. The brewing group douche is dirty
  1. Use a coarser grinding
  2. Put less coffee in the filter
  3. Press the coffee more gently
  4. Contact the nearest SERVICE CENTER
The machine does not work and the ON light does not come on
  1. No power
  2. The power cord is not properly plugged in
  3. The power cord is damaged
  1. Restore electrical power
  2. Plug in the power cord correctly
  3. Contact the nearest SERVICE CENTER for a replacement cord
The ON light is on but the ready steam indicator does not turn on within 10 minutes
  1. Thermostat malfunction
  2. Heating element malfunction
  1. Contact the nearest SERVICE CENTER
  2. Contact the nearest SERVICE CENTER

ESSENTIAL SAFETY WARNINGS

shock hazard As with all electrical appliances, the risk of electric shock cannot be excluded, therefore, the following safety warnings should be carefully observed.

To avoid spilling the connector, never pull the power cord.

  • Always attach plug to appliance first, then plug cord into the wall outlet.
  • To disconnect the appliance, turn any control to "off", then remove plug from wall outlet.
  • In the event of any fault, malfunction or damage, do not attempt to carry out repairs. Switch the appliance off, remove the plug and contact the Service Centre.
  • In the event of damage to the plug or the power cord, do not operate the appliance, these should be replaced only and exclusively by the Service Centre.
  • Unplug from outlet when not in use.
  • Before cleaning the exterior surfaces of the appliance, putting on or taking off parts, switch it off, remove the plug from the outlet and allow to cool.
  • To reduce the risk of injury do not drape cord over the counter top or table top where it can be pulled on by children or tripped over unintentionally.
  • Do not let cord touch hot surfaces.
  • Do not let cord hang over edge of table or counter.
  • burn hazardshock hazard
    The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or injury to persons.
  • Do not place on or near a hot gas or electric burner, or in a heated oven.
  • Before switching on, ensure that the power supply voltage corresponds to that indicated on the plate on the base of the appliance and that the power supply is properly earthed.
  • Do not tamper with the appliance. Contact an authorized technician or the nearest service centre for any problem.
  • Do not touch the appliance if your hands or feet are wet.
  • Do not touch the plug with wet hands.
  • Ensure that the electrical outlet is always freely accessible so that the plug can be easily removed when necessary.
  • When removing the plug, always hold it directly. It should never be removed by pulling on the power cord, as this can cause damage.
  • burn hazardshock hazard
    To protect against fire, electric shock and injury to persons do not immerse cord, plugs in water or other liquid.
  • Do not use adapters, multiple sockets or extension cords. If their use is unavoidable, use simple adapters or multiple sockets and extension cords that conform to current safety standards, taking care not to exceed the current limit marked on the simple adapter or extension cord, or the maximum capacity of the multiple sockets.

WARNING ABOUT BURN/SCALD RISKS

burn hazard This appliance produces hot water and steam; therefore, the following safety warnings should be strictly observed


  • hot surfaces remain hot for a certain time also after use. Do not touch hot surfaces. Use handles or knobs.
  • Take care to avoid contact with water spray or jets of steam.
  • When the appliance is switched on, do not touch the cup warming plate as it is hot.
  • Never direct the steam or water spray towards your body.
  • Be careful when touching the steam/hot water dispensing wand (6).
  • Never remove the filterholder (8) during operation.
  • The parts labelled "CAUTION HOT" are very hot, so approach and operate them with maximum caution.
  • Only place cups and glasses for use with the coffee machine on the cup warmer (2). Other objects should not be placed there.
  • Dry the cups thoroughly before placing them on the cup warmer (2).

SAVE THESE INSTRUCTIONS

The inserted data and pictures can be subject to changes without previous notice for the improvement of the machine's performances.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Lelit Anna PL41EM Manual

Advertisement

Need help?

Need help?

Do you have a question about the Anna and is the answer not in the manual?

Questions and answers

Table of Contents