Related Manuals for Yardworks 239-1574
Summary of Contents for Yardworks 239-1574
- Page 1 Corded POLE SAW 239-1574 OPERATOR’S MANUAL TOLL-FREE HELPLINE: 1-888-497-7273 Read this operator manual before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL - 01 -...
-
Page 2: Table Of Contents
TABLE OF CONTENTS SAFETY SYMBOLS ......................02 GENERAL POWER TOOL SAFETY WARNINGS ..............04 TRANSPORTATION AND STORAGE ................08 KNOW YOUR PRODUCT ....................10 ASSEMBLY OF THE MACHINE ..................11 OPERATION ........................13 CLEANING AND MAINTENANCE ..................16 TROUBLE SHOOTING .......................18 WARRANTY ........................20 SAFETY SYMBOLS The purpose of safety symbols is to attract your attention to possible danger. The safety symbols and the explanations with them deserve your careful attention and understanding. - Page 3 SYMBOL DESCRIPTION SYMBOL DESCRIPTION Read and understand all instructions before operating the product, follow all Wear eye, ear and head protection. warnings and safety instructions. Wear non-slip safety footwear when Wear protective gloves using the product. Disconnect from the mains plug if the cord is damaged or entangled.
-
Page 4: General Power Tool Safety Warnings
GENERAL POWER TOOL SAFETY WARNINGS WARNING: When using the product, the safety rules must be followed. For your own safety and that of bystanders, you must read and fully understand these instructions before operating the product. Please keep these instructions safe for later use. WARNING: Save all warnings and instructions for future reference. - Page 5 users. 4. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any oth- er condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 5.
- Page 6 PRUNER SAFETY WARNINGS 1. Never use the pruner when there is a possibility of thunderstorm or lightning. Store the pruner and the power cables safely indoors. 2. Ensure all guards, handles are properly fitted and are in good condition. 3. Do not start using the product until you have a clear work area, secure footing, and a planned retreat path away from the falling branches or limbs.
- Page 7 22. If the chain and bar become pinched or trapped in branches too high to reach, seek advice from a pro- fessional tree service specialist about safe removal of the cutting means. WARNING: Check that all the shaft couplings on the extension pole and tool are securely fastened before each use and at frequent intervals.
-
Page 8: Transportation And Storage
TRANSPORTATION AND STORAGE 1. Stop the machine, disconnect from mains and allow it to cool before storing or transporting. 2. Clean all foreign material from the product. Store it in a cool dry and well-ventilated place that is inacces- sible to children. Keep away from corrosive agents such as garden chemicals and de-icing salts. Do not store outdoors. - Page 9 It is not intended to be used whilst climbing or as a conventional chainsaw for close quarter limbing and pruning of material at ground level. RESIDUAL RISKS Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors.
-
Page 10: Know Your Product
KNOW YOUR PRODUCT 1.Chain lubricant cap 2.Chain Tension ring 3.Shaft coupling 4.Extension Pole 5.Middle Pole 6.Start Button 7.Cord retainer 8.Lock Off Safety Button 9.Saw Chain 10.Guide bar 11.Chain Wheel Guard 12.Fastening knob - 10 -... -
Page 11: Assembly Of The Machine
Item No. 2391574(EGTACPS001) Nominal voltage 120V/60HZ Current Tension Cutting speed 36 f/s No Load Speed 6200 RPM Cutting length 10” Oil tank capacity Max 75ml *) The specified values are emission values and do not necessarily represent safe workplace values. Al- though there is a correlation between emission and immission levels, this cannot be used to infer wheth- er additional safety measures are necessary or not. - Page 12 3. Assembly of the cutting head and 5. Assembling the saw bar and saw Pole chain Take out the Pole Assembly and the Cutting a. Loosen the fastening knob (12) on the chain Head Assembly. wheel guard (11) and remove chain wheel g.
-
Page 13: Operation
OPERATION Checking the tensioning of the saw chain WARNING! Safety equipment RISK OF INJURY! The device has several pieces of safety A new saw chain must be re-tensioned after a equipment which reduce the risk of injury when maximum of five cuts. This is normal during the working: run-in time;... -
Page 14: Cleaning And Maintenance
CLEANING AND Cleaning the device ● Remove coarse dirt. MAINTENANCE ● Wipe down the device with a slightly damp cloth. Cleaning the oil guide groove of the saw DANGER! rail RISK OF INJURY! Before any maintenance or cleaning work: Use plastic brush to clean the saw rail. –... - Page 15 Transport If you are transporting the device in a vehicle: – Slip the protective cover onto the cutting tool. – Secure the device against slipping. – If possible, use the original packaging for dis- patching. DISPOSAL Disposal of the appliance Appliances which are labeled with the adjacent sym- bol must not be disposed of in household waste.
-
Page 16: Trouble Shooting
TROUBLE SHOOTING Problem Possible Cause Solution No mains voltage? Check cable, plug, socket and fuse. Motor not running. Cable faulty? Have replaced by an electrician. If you are unable to remedy the fault yourself, please contact your local store. Please note that improper per- formance of repair work will lead to the loss of any warranty claims and that additional costs may be incurred. -
Page 17: Warranty
SKU# 239-1574 YARDWORKS WARRANTY POLICY ● Two (2) year limited warranty on all Yardworks C o r d e d power tools from date of purchase when used for personal, household, or family use. ● Warranty voided if used for commercial or industrial purposes or any other improper use as determined by Yardworks. - Page 18 - 18 -...
Need help?
Do you have a question about the 239-1574 and is the answer not in the manual?
Questions and answers