WARING COMMERRCIAL PRO PREP WCG75 - Chopper Grinder Manual

PARTS INCLUDED

1. Motor base
2. Grinding work bowl
3. Grinding work bowl cover
4. Grinding blade (3-blade configuration)
5. Chopping work bowl
6. Chopping work bowl cover
7. Chopping blade (2-blade configuration)
8. Motor shaft (not shown)
9. 3-position paddle switch

TO HELP KEEP YOUR PRO PREP CHOPPER-GRINDER WORKING AT ITS VERY BEST AND INCREASE ITS SERVICE LIFE, DO THE FOLLOWING:

1. WASH, RINSE, SANITIZE AND DRY ALL REMOVABLE PARTS THOROUGHLY PRIOR TO INITIAL USE AND AFTER EACH USE.
2. CLEAN AND SANITIZE THE MOTOR BASE PRIOR TO INITIAL USE AND AFTER EVERY USE.

OPERATION FOR COMMERCIAL USE

1. Put base on counter near electrical outlet. Do not plug in until the Pro Prep Chopper-Grinder is totally assembled.
2. Put empty work bowl (either grinding or chopping) on base, fitting center tube over shaft on base, and position handle slightly to left of front center (7 o'clock).
3. Hold bowl by handle and turn bowl counterclockwise until unit locks in place.
4. Pick up metal blade by center plastic hub. Never touch metal cutting blades. Place blade over motor shaft, twisting gently until it drops into place over shaft.
5. NOTE: You must use the designated processing blades with the designated work bowl (chopping blade with chopping bowl or grinding blade with grinding bowl). Using the Pro Prep Chopper-Grinder in any other way will damage the unit and may result in injury.
6. Cut larger food items into 1-inch (2cm) cube before processing. For recommended amounts and processing times, see chart listings below.
7. Place cover on work bowl. Motor will not start unless work bowl is securely locked in position and cover is securely locked on work bowl. Turn cover in direction of arrow to lock.
8. W ith the paddle switch in OFF position, plug into power outlet. Move paddle switch to ON or PULSE to operate.
9. When finished processing, set paddle switch to OFF position.
10. Allow motor to come to a complete stop and always unplug before removing lid and/or work bowl.
11. Operate for maximum of 1 minute on, 5 minutes off.

PROCESSING QUANTITY GUIDELINE

This appliance is not designed or intended to process meats.

NOTE: This table only to be used as a guideline. Actual quantities may vary.

CARE AND CLEANING

FOOD SERVICE USAGE:

To Clean and Sanitize Motor Base
UNPLUG POWER CORD. Wipe down exterior surfaces of motor base with soft cloths or sponges dampened with washing solution (for your safety, use water no hotter than 115ºF), rinse water, and sanitizing solution. Prevent liquid from running into motor base by wringing all excess moisture from cloths or sponges before using them. Allow motor base to air-dry before using.
NOTE: Motor base is not for water jet cleaning.

DO NOT IMMERSE THE BASE UNIT IN WATER OR OTHER LIQUID.

To Clean and Sanitize Work Bowls, Blades and Lid
REMOVE WORK BOWL FROM MOTOR BASE.
Dishwasher: Remove lid and blade. Place work bowls, blades and lid on flat dish rack and run through wash cycle. Let air-dry.
Hand-washing (triple sink configuration): Remove lid and blade. In the first sink, add detergent and water amount according to detergent package label. Scrub and flush out the work bowls, blades and lid to dislodge and remove food residue. Rinse in second sink, then sanitize in third sink according to instructions on sanitizer label.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

1. READ ALL INSTRUCTIONS.
2. Always unplug from outlet when not in use, before putting on or taking off parts, before removing food from processor and before cleaning.
3. To protect against electrical hazards, do not immerse the base unit in water or other liquid.
4. Be certain to maintain adequate mechanical stability when in use, during transportation, assembly, dismantling, scraping and any other action involving the appliance.
5. Avoid coming into contact with all moving parts. Let machine come to a complete stop before removing lid. Do not try to override cover interlock. Injury may result.
6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or electrical or mechanical adjustment.
7. The use of attachments not sold by Waring is not recommended and may be potentially hazardous.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter or touch hot surfaces.
10. Keep hands and utensils out of container while in operation to prevent the possibility of severe personal injury and/or damage to the unit.
11. To reduce the risk of injury, never place cutting blade on base without first putting bowl properly in place.
12. Be certain cover is securely locked in place before operating appliance.
13. Blades are sharp. Handle carefully. When not in use, store blades only inside locked and secured work bowl.
14. The Pro Prep Chopper-Grinder is designed to use designated processing blades with the designated work bowl (chopping blade with chopping bowl or grinding blade with grinding bowl). Using the Pro Prep Chopper-Grinder in any other way will damage the unit and may result in injury.
15. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
    Children should be supervised to ensure that they do not play with the appliance.

SAVE THESE INSTRUCTIONS!

GROUNDING INSTRUCTIONS

For your protection, this appliance is equipped with a 3-conductor cordset.
120-volt units are supplied with a molded 3-prong grounding-type plug (NEMA 5-15P) and should be used in combination with a properly connected grounding type outlet as shown in Figure 1.

If a grounding type outlet is not available, an adapter, shown in Figure 2, may be utilized to enable a 2-slot wall outlet to be used with a 3-prong plug.

As shown in Figure 3, the adapter must be grounded by attaching its grounding lug under the screw of the outlet cover plate.

Before using an adapter, it must be determined that the outlet cover plate screw is properly grounded. If in doubt, consult a licensed electrician. Never use an adapter unless you are sure it is properly grounded.

LIMITED WARRANTY

Under this warranty, the Waring Commercial division will repair or replace any part which, upon our examination, is defective in materials and workmanship, provided the product is delivered prepaid to the Waring Service Center, 314 Ella T. Grasso Ave., Torrington, CT 06790, or any factory-approved service center.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download WARING COMMERRCIAL PRO PREP WCG75 - Chopper Grinder Manual