Advertisement
Quick Links
This product contains a chemical or chemicals known to the State of California to
The engine exhaust from this product contains chemicals known to the State of California
Loose Parts
Use the chart below to verify that all parts have been shipped. Part numbers not shown are available on the dealer
extranet.
Dealer Pack
Part No.
323-4
3290-357
107-4543
322-10
3256-3
104-8300
323-6
3296-39
1-806003
1-808286
1-806003
322-9
3296-29
1-303287
103-2106
1-603511
Literature Pack
Manual, Operator's
Manual, Engine Owner's (Non-Exmark Engines)
© 2017—Exmark Mfg. Co., Inc.
P.O. Box 808
Beatrice, NE 68310
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
to cause cancer, birth defects, or other reproductive harm.
Description
Screw, HH 3/8-16 x 3/4 inch
Nut, Whizlock 3/8-16 inch
Clamp, Tank
Screw, HH 5/16-18 x 2
Washer, 5/16 Std
Nut, Nyloc 5/16-18 Flg
Screw, HH 3/8-16 x 1 inch
Nut, Nyloc 3/8-16 inch
Hairpin, Cotter
Pin, Clevis (Pistol Grip Only)
Hairpin, Cotter (Pistol Grip Only)
Screw, HH 5/16-18 x 1 3/4 inch (ECS
Only)
Nut, Nyloc 5/16-18 inch (ECS Only)
Tie, Cable
Key, Exmark Logo
Key, Standard
WARNING
CALIFORNIA
Qty.
8
8
2
2
2
2
4
4
2
2
2
2
2
2
1
1
Setup Instructions
For Serial Nos. 402,082,300 & Higher
Use
Installing the front caster wheels.
Installing the fuel tank.
Installing the handle assembly.
Install the PTO engagement linkage.
Installing and adjusting the wheel
drive linkages.
Connecting the wire harness.
Fill out the online warranty registration
form and place keys into literature
pack.
All Rights Reserved *4503-442* A
Part No. 4503-442 Rev. A
Printed in the USA
METRO
®
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Exmark METRO 402 Series
Summary of Contents for Exmark METRO 402 Series
- Page 1 1-603511 Key, Standard pack. Literature Pack Manual, Operator's Manual, Engine Owner’s (Non-Exmark Engines) © 2017—Exmark Mfg. Co., Inc. All Rights Reserved *4503-442* A Part No. 4503-442 Rev. A P.O. Box 808 Printed in the USA...
- Page 2 Uncrating the Unit nut. The handle can now be pivoted to allow positioning in one of the three holes allowing various adjustments Leaving the unit on the pallet, place the upper handle for operator comfort (Figure 2 and Figure 3). Once a assembly, the fuel tank, and the shifter lever at the proper position is found, install one 3/8 x 1 inch bolt in rear of the machine.
- Page 3 Attach throttle cable to engine: Position the throttle control lever (located on the console) in the full throttle position. You will feel a detent when the throttle lever is pushed towards the upper end of the slot. Attach the inner wire of the throttle cable to the top hole in the throttle control lever as shown in Figure 4.
- Page 4 g006810 Figure 7 1. Shifter lever 3. Adjustment slots 2. Equal distance g006802 Figure 9 1. 3/16 inch to 1/4 inch (4.7mm to 6.4mm) Installing and Adjusting the Wheel 2. Neutral lock/park brake latch 3. Drive linkage Drive Linkages Note: The neutral lock/park brake latch clearance For Pistol Grip Handles: should be checked where there is a slight upward Screw the threaded end of the drive linkages into the...
- Page 5 Locate two 5/16-18 x 1 3/4 inch hex capscrews and two 5/16-18 inch nyloc nuts in the bolt bag. Thread the drive lever linkage into the swivel located on the wheel drive idler arm. Thread the drive lever linkage in until the flat edge of the drive lever aligns with the bottom of the roller notch in the neutral lock/park brake latch when the 5/16-18 x 1 3/4 inch hex capscrew is inserted through the hole in the...
- Page 6 Checking Tire Pressure Check the tire pressure in the drive tires. Proper inflation for drive tires is 12-16 psi (83-110 kPa). Adjust the tire pressure within 12-16 psi (83-110 kPa) range to make the tire circumferences match as closely as possible. Greasing the Unit Note: The unit is not greased at the factory.
-
Page 7: Servicing The Engine
48 inch Deck Shown for Reference Only Servicing the Engine The engine is shipped with oil; check oil level and if necessary fill to the appropriate level. Exmark 4-Cycle Premium Engine Oil is recommended; refer to the Engine Owner's manual for an appropriate API rating and viscosity.
Need help?
Do you have a question about the METRO 402 Series and is the answer not in the manual?
Questions and answers