Advertisement
Quick Links
BEFORE YOU START
• To ensure the installation and erection of your Stratco Handi-Saver Shed proceeds smoothly, you should confirm that all the
components and materials listed in this installation guide have been supplied.
• Carefully read this installation guide to familiarise yourself with all the steps involved and ensure that you have the correct tools
and equipment for the job.
• There are different types of screws used. Ensure the correct type of screw is being used at each location.
• Do not traverse the roof of the Stratco Handi-Saver Shed.
• Use heavy gloves and safety glasses when handling steel and never attempt to install a shed in windy conditions.
FLOORING PREPARATION
The installer is responsible for ensuring the slab or concrete pads are sufficient to support the shed and sustain wind loading.
Do not directly anchor your shed to pavers.
Option 1 - Before building the shed, pour a base that is larger than the area by at least 200mm in each direction. The base should
be poured so the concrete outside the shed floor area slopes away from the shed to help prevent water from entering the shed.
Option 2 - Substantial concrete pads may be used at each anchor location as an alternative to a complete concrete floor. It is
recommended pads are minimum Ø250mm x 400mm deep, embedded into a firm natural soil base.
TOOLS AND HARDWARE REQUIRED
• Cordless Drill
• 5/16 Hex-head & PH2 Phillips-head Bit
• 3.5mm & 5mm Steel Drill Bit
• 10mm Masonry Drill Bit
• Adjustable Spanner
• Tin Snips (Optional)
HANDI-SAVER
• Rivet Gun
• Tape Measure
• Ladder/ Step Ladder
• Trestles/ Table
• Safety Gloves
• Safety Glasses
HANDI SAVER SHED INSTALLATION GUIDE
SHED
®
Advertisement
Related Manuals for Stratco HANDI-SAVER SHED
Summary of Contents for Stratco HANDI-SAVER SHED
- Page 1 BEFORE YOU START • To ensure the installation and erection of your Stratco Handi-Saver Shed proceeds smoothly, you should confirm that all the components and materials listed in this installation guide have been supplied. • Carefully read this installation guide to familiarise yourself with all the steps involved and ensure that you have the correct tools and equipment for the job.
- Page 2 HANDI-SAVER INSTALLATION GUIDE COMPONENTS Door Frame & Door Shroud Wall Channel 2 x 1840mm Door Frame Vertical 4 x 700mm Wall Channel (Short) 2 x 750mm Door Frame Horizontal 4 x 1400mm Wall Channel (Long) 1 x 760mm Door Shroud Flashing (Front &...
- Page 3 SHORT WALL ASSEMBLY Wall Channels have three pilot holes in each end. Fasten through the pilot holes of each end first, then fasten the Note: The ‘Sheet Crest’, as referenced throughout this guide, middle screws secondly. refers to the curved top faces of the sheet. Sheet Crest Fasten through Fasten middle...
- Page 4 HANDI-SAVER INSTALLATION GUIDE Ensuring the Door Jamb is up against the Corner Sheet, FRONT WALL ASSEMBLY fasten a 10x16 Hex-Head Screw through the Wall Channels Fit two Wall Channels (Long) over the ends of the Split Front (Long) and into the Door Jamb at both ends. Corner Sheet.
- Page 5 At the corner where the Wall Assemblies fit together, fit a Fit the corner end of the Short Wall Assembly over the lap Corner Bracket. The Corner Bracket fits over the Wall end of the Long Wall Assembly. Channels at the top. Short Wall Assembly Long Wall Assembly Wall Channel...
- Page 6 HANDI-SAVER INSTALLATION GUIDE Fit a Corner Bracket over the Wall Channels at the bottom Fit a Corner Bracket over the Wall Channels at the top corner. corner. Fasten the Corner Bracket to the Wall Channels Fasten the Corner Bracket to the Wall Channels through the through the pilot holes using four 10x16 Hex-Head Screws.
- Page 7 Fit a Corner Bracket over the Wall Channels at the bottom corner. Fasten the Corner Bracket to the Wall Channel (Short) through the pilot holes using two 10x16 Hex- Head Screws. Corner Bracket 10x16 Hex-Head Screw Front Wall Assembly FIGURE 4.12 Fit the Door Shroud into the door opening.
-
Page 8: Door Assembly
HANDI-SAVER INSTALLATION GUIDE DOOR ASSEMBLY Turn the door over so that the underside is facing up. Loosely fit the three Door Braces into the Door Assembly. The Door Fit the Horizontal and Vertical Door Frames over the Door Brace ends fit inside the Door Frames. Sheet. - Page 9 Drill two 3.5mm holes through each Door Brace and into Stand the Door on it’s side so that the Padbolt Mount Plate is the Door Sheet. Ensure holes are drilled into every third located against the ground. Position one Hinge onto the sheet pan.
- Page 10 HANDI-SAVER INSTALLATION GUIDE DOOR FITMENT Using the marks from the previous step as a guide, position a Door Jamb Bracket in place. The Door Jamb can be rotated Note: the door can open from the middle or end of the shed to fit the Door Jamb Bracket inbetween the Wall Sheet and depending on preference.
- Page 11 Hang the door in place, ensuring a 5mm gap between the Position the left Door Jamb to achieve a 5mm gap between bottom of the Door and the Door Shroud. Using the Hinge the Door Jamb and Door Frame. Fasten a 10x16 Hex-Head holes as a guide, drill one 5mm hole into the Door Jamb and Screw through the Corner Bracket and into the Door Jamb install a 4.8mm Rivet for both Hinges.
-
Page 12: Roof Assembly
HANDI-SAVER INSTALLATION GUIDE Install the Padbolt to the Mount Plate using four 10x16 Fit a Flashing (Left & Right) and a Flashing (Front & Rear) onto Wafer-Head Screws. Ensure the Padbolt body sits flush to the Roof Sheet. Drill a 3.5mm hole and fasten a 3.2mm the Door edge. - Page 13 FIGURE 8.1 FIGURE 8.2 « SCAN THIS QR CODE TO FIND A STRATCO NEAR YOU 1300 155 155 stratco.com.au All brands and logos/images accompanied by ® or ™ are trade marks of Stratco (Australia) Pty Limited. ® Copyright May 2023...
Need help?
Do you have a question about the HANDI-SAVER SHED and is the answer not in the manual?
Questions and answers