Related Manuals for Clarke VAC KING CVAC18V10
Summary of Contents for Clarke VAC KING CVAC18V10
- Page 1 20V 10L WET/DRY CORDLESS VACUUM CLEANER MODEL NO: CVAC18V10 PART NO: 6471102 OPERATING & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS DL0124...
-
Page 2: Specification
0 - 30 Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 3: Safety Precautions
9. NEVER use this cleaner if any part is damaged. Have it inspected and repaired by your CLARKE dealer. DO NOT use if the battery or the cleaner itself, is in poor condition.. 10. ALWAYS take care when a long hose is required in the work area as it presents a trip hazard. -
Page 4: Battery Safety
20. DO NOT attempt to repair or modify the cleaner charger or battery. DO NOT attempt any electrical repair yourself. Consult a qualified electrician or the CLARKE Service Department on 020 8988 7400. BATTERY SAFETY 1. Only use batteries and charger supplied with the cleaner. - Page 5 INVENTORY OF COMPONENTS No Description No Description On/Off Switch Brush Nozzle Carrying Handle Crevice Nozzle Flexible Plastic Hose Dry HEPA Filter Top Cover Wet Sponge Filter Tank Battery Charger Battery Compartment 4Ah Battery Suction Port 4 x Wheels (Not Shown) Triangle Nozzle Parts &...
-
Page 6: Environmental Protection
BATTERY CHARGER ELECTRICAL CONNECTIONS WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE CHARGER TO THE MAINS SUPPLY. Before switching the battery charger on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This battery charger is designed to operate on 230VAC 50Hz. -
Page 7: Preparation For Use
PREPARATION FOR USE WARNING: BEFORE USING THE VACUUM CLEANER, MAKE SURE THAT YOU HAVE READ AND UNDERSTOOD THE SAFETY INSTRUCTIONS UNPACKING & ASSEMBLY With the vacuum cleaner removed from the packaging, remove the components from within the tank. Lay them out and check for shortages and that no damage was suffered in transit. - Page 8 3. Insert the plastic hose into the required brush/nozzle and push in until it is a tight fit, brush nozzle shown FITTING/CHANGING THE FILTERS Filters are essential to ensure that dust or foreign matter does not enter the motor compartment which would reduce motor efficiency and eventually cause serious damage.
-
Page 9: Battery Installation
BATTERY INSTALLATION 1. Lift the battery compartment lid. 2. Slide the battery into the compartment, with the release clip on the outside. 3. Before use, make sure the compartment lid is firmly clipped down in place. 4. To check how much power is in the battery, press the power indicator button on the end of the battery. - Page 10 3. Make sure the hose is fixed to the suction port (see page 7) 4. Make sure that the motor housing is seated on top of the tank and the clips are locked in place, one on each side. 5. Switch on and start work. NOTE: The machine should be positioned on a firm, level surface, specially when...
-
Page 11: Troubleshooting
Battery is not well Check if there is any power charged left in the battery; or charge battery. Motor breakdown Take the cleaner to your CLARKE dealer for repair. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 12: Maintenance
MAINTENANCE WARNING: TAKE OUT THE BATTERY BEFORE DOING ANY MAINTENANCE WORK. IF PROPER CARE IS TAKEN TO MAINTAIN YOUR CLEANER, MOTOR MAINTENANCE IS UNNECESSARY. CLEANING YOUR FILTERS 1. Take the filter off the machine (see pages 8) 2. Wash the filters with water only, at 40°C max. 3. -
Page 13: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 14: Component Parts List
GUARANTEE This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for its intended purpose. -
Page 15: Component Parts
COMPONENT PARTS Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the VAC KING CVAC18V10 and is the answer not in the manual?
Questions and answers