Page 1
THE PROFESSIONAL SIDE BURNER Use and Care Guide MODELS: BGB131 BGB132 BGB131-BI BGB132-BI...
Page 2
A MESSAGE TO OUR CUSTOMERS We are glad that you selected the Professional Side Burner by DCS. Because this appliance contains features not found on any other burner, we recommend that you read this entire booklet before your first use. Keep it in a handy place as it has answers to questions that may occur during future use.
SAFETY PRACTICES AND PRECAUTIONS SIDE BURNER 131/132 SIDE MOUNT MODEL INSTALLATION SIDE BURNER BUILT-IN MODEL INSTALLATION GAS REQUIREMENTS Natural Gas Hook-up...8 LP Gas Hook-up...9 LP Tank Requirements ... 9 LEAK TESTING AND LIGHTING INSTRUCTION Lighting Instructions ...10 Match Lighting...11 FINAL CHECKLIST ...12...
Should the burner go out during use, turn off the gas valve and wait 5 minutes before attempting to relight. Always follow the lighting instructions. Never lean over a lit burner. Never cook without the drip pan in place, pushed all the way to the rear of the burner box. Use only in well ventilated areas.
3. The Professional Side Burner heats unevenly. 4. The burner(s) make popping noises. Do not attempt to disconnect any gas connections while your burner is in use, or the gas supply is on. When the Professional Side Burner is stored indoors the gas supply must be disconnected and, if using an LP gas cylinder, the cylinder must be stored outdoors in a well-ventilated area.
Page 6
SIDE BURNER 131/132 SIDE MOUNT MODEL INSTALLATION 15 -3/4" 10-3/8" " 12- 3/4 " IGNITION BURNER 3/8" " Standard construction MODEL BGB131 BGB132 2" X 2" opening for gas supply line 26- 3/4" 10-3/8" " 23- 3/4" REAR IGNITION FRONT 3/8" "...
SIDE BURNER BUILT-IN MODEL INSTALLATION INSTALLATION OF SIDE BURNER BUILT-IN: All BGB131-BI and BGB132-BI models can be installed in combustible enclosure with zero clearance from the back, side and bottom. A minimum of 6” from the back and sides must be...
Page 8
14 -3/4" 10-1/16" " 11- 3/4" Standard construction 2" X 2" opening for gas supply line note: the deck is not required Dual Side Burner 25- 1/2" " 22- 1/8" 25- 1/2" 12" MODEL BGB131-BI 12" BGB132-BI 22-3/8" 10- 1/16" 10-1/16"...
Gas conversion kits are available from the factory. When ordering, have the model number, and the type of gas (natural or LP) which you need. Total gas consumption of the Professional Side Burner with burner(s) on “HIGH”: Table 1 below. MODEL...
Side Burner uses the LP regulator from adjoining grill. Apply joint compound to the threaded end of the Side Burner gas inlet and tighten the adapter to the pipe. Assemble the 24” and 30” hoses to the 3/8” flare tee, as shown in Fig.04.
Do not use the Professional Side Burner if the odor of gas is present. Turn the control knob to “OFF” , then turn off the gas supply. If using LP, is there gas in the tank? Always keep your face and body as far away from the burner as possible when lighting.
LIGHTING INSTRUCTIONS MATCH LIGHTING Hold a fireplace lit match near the burner ports, turn the control knob counterclockwise to “HI” . Move your hand immediately once the burner is lit. Rotate the control knob to the desired setting. Note: If you are using propane gas, a slight...
SIDE BURNER GRATE The side burner grate is porcelain enamel over cast iron for durability. To avoid burns do not clean a hot grate. They may be wiped while in place with hot, soapy water, rinsed and wiped dry thoroughly.
Check the burner for obstructions or dirt. See Fig. 09. Check for proper gas supply or wrong gas. Is the Side Burner in a dusty area? Move to less dusty area if possible. Is the fuel hose bent or kinked? See Fig. 03 and Fig. 04.
SINGLE SIDE BURNER PARTS LIST FOR BGB131 & BGB131-BI NOTE: Part list typical for BGB131 & BGB131-BI models. Illustration shows BGB131-BI model. ITEM DESCRIPTION BURNER COVER PULL HANDLE RUBBER BUMPER TOP GRATE BK D BURNER CAP PORT RING ASSEMBLY VENTURI...
DOUBLE SIDE BURNER PARTS LIST NOTE: Part list typical for BGB132 & BGB132-BI models. Illustration shows BGB132-BI model. ITEM DESCRIPTION BURNER COVER PULL HANDLE RUBBER BUMPER TOP GRATE BK D BURNER CAP PORT RING ASSEMBLY VENTURI BASE D BURNER PLATE SUPPORT BURNER...
SINGLE & DOUBLE SIDE BURNER WIRING DIAGRAM SINGLE SIDE BURNER SPARK ELECTRODE (P/N 12224) (Switch is built into module) BATTERY TERMINAL IGNITION MODULE 1.5 VOLT (P/N 16566) ALKALINE BATTERY P/N 16567) SPARK ELECTRODE (P/N 12224) NOTE: HIGH VOLTAGE AT TERMINALS...
LENGTH OF WARRANTY DCS warrants all other Side Burner components parts and labor to the original purchaser to be free of factory defects in material and workmanship for a period of one (1) year from the original date of purchase. This does not apply if the unit was subjected to other than normal residential use.
SERVICE HOW TO OBTAIN SERVICE: For warranty service, please contact your local service provider or DCS Customer Care Center at (888) 281-5698, Monday thru Friday, 6 am- 4:30 pm PST. Before you call, please have the following information ready: Model Number (located on the inside of the left side of the appliance)
Page 22
5800 Skylab Road, Huntington Beach, CA 92647 Tel: 714.372.7000 • Fax: 714.372.7001 Customer Service: (888) 281.5698 www.dcsappliances.com As product improvement is an ongoing process at DCS, we reserve the right to change specifications or design without notice. Part No. 17712 Rev. B...