Roland V-Drums TD713 Setup Manual

TD713 Setup Guide TD713 Setup Guide
01 01
Checking the included items
As soon as you open the package, check to see that all items are included.
If anything is missing, please contact your dealer.
¹ V71 (drum sound module) x 1 ¹ Owner's Manual
¹ PD-14DSX (digital snare) x 1
– TD713 Setup Guide (this document)
¹ CY-18DR (digital ride) x 1
– V71 Quick Start
¹ VH-14D (digital hi-hat) x 1
– Roland Cloud Connect Setup Guide
¹ PDX-100 (tom 1, 2, 3, 4) x 4
– Roland Cloud Activation Card
¹ CY-14R-T (crash 1) x 1
– PD-14DSX Owner's Manual
¹ CY-16R-T (crash 2) x 1
– CY-18DR Owner's Manual
¹ MDH-STD (pad mount) x 1
– VH-14D Owner's Manual
¹ Drum Key x 1
– PDX-100 Owner's Manual
– CY-16R-T / CY-14C-T Owner's Manual
– CY-14R-T / CY-12C-T Owner's Manual
KD-12 (kick drum) MDS-Grand 2 (drum stand)
* When checking the items included * When checking the items included with
with the KD-12, refer to "KD-12 Owner's the MDS-Grand 2, refer to "MDS-Grand 2
Manual". Owner's Manual".
02 02
Assembling the drum stand (MDS-Grand 2)
Assemble the stand using the procedure described in "MDS-Grand 2 Owner's
Manual".
Cymbal mount Cymbal mount
Pad mount Pad mount
Sound module
mounting plate
Hand knob Hand knob
Hand knob Hand knob
1.5 m
Now you've finished the first half of the assembly process. Why not take a break?
05 05
Attaching the parts
* For details on each component, refer to the respective owner's manual.
Precautions regarding placement of this unit on a stand
Be sure to follow the instructions in the "TD713 Setup Guide" (this document) carefully when placing this
unit on a stand.
If it is not set up properly, you risk creating an unstable situation which could lead to the unit falling or the
stand toppling, and may result in injury.
Setting up the hi-hat (VH-14D)
Insert the plug of the connecting cable included with the
VH-14D into the DIGITAL TRIGGER OUT plug of the VH-14D.
Protector
Connection cable
Use the protector to lock the connection.
* While playing, the "¹" (round dot) marks on the top and
bottom cymbals should be lined up, as shown in the
illustration. The product may not work correctly if the
marks aren't lined up.
* Position the cymbals so that the Roland logo is on the
far side facing away from the player.
Attaching the drum sound module (V71)
Wide Wide
Narrow Narrow
Sound module Sound module
mounting plate mounting plate
Insert the mounting plate into the clamp, then turn the clamp
knob to secure the mounting plate.
Attach the cables to the stand with the cable tie.
*5100085666-02*
Time required Time required
: approx. : approx.
TD713
¹ Cables
– Dedicated Trigger
Cable (included with
MDS-Grand 2)
– Trigger cable (for
connecting tom 4) x 1
– Connecting Cable
x 3 (included with
PD-14DSX, CY-18DR
and VH-14D)
* V71, PD-14DSX, CY-18DR, VH-14D,
CY-14R-T and CY-16R-T accessories are in
the respective packing cartons.
* This package does not include a kick
pedal, a hi-hat stand, and a snare
stand. Use with a commercially
available kick pedal, hi-hat stand, and
snare stand.
Time required Time required
: approx. : approx.
MDH-STD MDH-STD
Cymbal mount Cymbal mount
Pad mount Pad mount
Attach the MDH-STD
(pad mount) included
with the TD713.
* Be sure the two pipes at the ends are no
more than 1.5 meters apart. Cause the stand
to fall over.
Attaching the crash cymbal (CY-14R-T / CY-16R-T) and ride cymbal (CY-18DR)
1. Position the cymbal so that the
convex portion of the cymbal
mount is aligned with the
concave portion of the bottom of
the cymbal.
2. Tighten the cymbal nut to obtain
an appropriate amount of sway.
CR1 (BOW/EDGE) CR1 (BOW/EDGE)
CY-14R-T CY-14R-T
(HI-HAT) (HI-HAT)
VH-14D VH-14D
V71 V71
Mounting the snare (PD-14DSX) on a snare stand
1. Insert the plug of the
The PD-14DSX can only be used with a The PD-14DSX can only be used with a
commercially available snare stand. commercially available snare stand.
connecting cable included
with the PD-14DSX into
the DIGITAL TRIGGER OUT
plug of the PD-14DSX.
* Make sure that the snare stand
you are using is able to support a
14-inch shell.
03 03
Assembling the hi-hat (VH-14D)
40 40
Assemble the hi-hat using the procedure described in "VH-14D Owner's Manual".
min. min.
1. Place the bottom cymbal on the hi-hat
stand with the cymbal rod passing through
the bottom cymbal hole.
2.
Pass the ends of the clamp through the
grooves in the metal portion of the bottom
cymbal, then while strongly pulling the
clamp downward, secure it with the drum
key.
30 30
min. min.
04 04
Assembling the kick drum (KD-12)
Assemble the kick drum using the procedure described in "KD-12 Owner's Manual".
NOTE
During assembly, take care that the weight of the kick drum does not pinch your hand or foot.
Take care not to pinch your fingers.
1. With the unit assembled, 2.
loosen the leg fastener
knob, adjust the angle of
the leg and then tighten
the leg fastener knob.
Using a drum key, to adjust
the length of the rods so that
the left and right are the same
length.
Leg fastener knob Leg fastener knob
Rod
* Use the cymbal nut and felt washer
that are included with the drum stand.
Cymbal nut Cymbal nut
Felt washer Felt washer
"Roland" logo on the farther side, "Roland" logo on the farther side,
as viewed from the player as viewed from the player
Convex portion Convex portion
(RIDE) (RIDE)
CY-18DR CY-18DR
T2 T2
T1 T1
PDX-100 PDX-100
PDX-100 PDX-100
T3 T3
PDX-100 PDX-100
KIK KIK
(SNARE) (SNARE)
KD-12 KD-12
PD-14DSX PD-14DSX
Adjusting the kick drum (KD-12)
1.
Adjust the tip of the legs (spike/
rubber) appropriately for the
surface on which you're placing
the KD-12.
Spike Soft floor
Protector Protector
V-Drums mat (TDM series),
carpet, etc.
Rubber
Hard floor
Connection cable Connection cable
Wood flooring, concrete, etc.
If you loosen the foot nut and rotate the
foot to raise it, the spike will be exposed.
Use the protector to Use the protector to
Tighten the foot nut to secure the
lock the connection. lock the connection.
position of the foot.
3. Connect the link cables A/B on the top
cymbal to the link jacks A/B of the bottom
cymbal.
View from the side
Cable in Cable in
back back
Hi-hat stand felt
(or rubber)
* Don't pull the link cables too hard when assembling
this product.
* Make sure that both the top cymbal and bottom
cymbal can be opened and closed smoothly.
Pull down and Pull down and
tighten with the tighten with the
drum key. drum key.
Clamp Clamp
Attach the kick pedal. Using a felt beater
Adjust the rod length so that
the kick pedal touches the floor.
1. To protect the batter
head pad face, be sure to
apply the included kick
drum patch to the pad
face.
Rod Rod
When using a non-felt beater,
you can keep using the pad
normally with the patch still on.
Bottom face of kick pedal fully Bottom face of kick pedal fully
touches the floor touches the floor
Refer to the "KD-12 Owner's
Manual" for details on how to apply
the included anti-slip sheet.
3. Insert the plug of the connection
cable into the CY-18DR's DIGITAL
TRIGGER OUT connector.
Attaching the tom (PDX-100)
CR2 (BOW/EDGE) CR2 (BOW/EDGE)
CY-16R-T CY-16R-T
T4 T4
PDX-100 PDX-100
Exposing the spike Exposing the spike Tightening the foot nut Tightening the foot nut
Foot nut Foot nut
Foot Foot
Spike Spike
* The tip of the spike is sharp; handle it
with care.
* Using the spike leg tips on wood flooring
may damage the floor; the rubber leg tips
should be used on wood flooring.
2.
Adjust the beater position.
Adjust the length of the beater so that the
beater strikes the center of the pad face.
Assembly and connections
150
Time required
: approx. min.
10 10
Time required Time required
: approx. : approx. min. min.
Cable in Cable in
front front
10 10
Time required Time required
: approx. : approx. min. min.
* If you wish to remove the marks
(adhesive) that remain after you
peel off the patch, wipe them
off with a cloth and rubbing
alcohol.
* Do not use rubbing alcohol
on any other parts besides the
batter head pad face. Using
rubbing alcohol on plastic
or wooden parts may cause
discoloration or damage.
50 50
Time required Time required
: approx. : approx. min. min.
Protector
Connection cable
DIGITAL TRIGGER OUT connector
Use the protector to
lock the connection.
Loosen Loosen
Tighten Tighten
Rod Rod
Using double kick pedals
The KD-12 can also be used with a twin
(double kick) pedal.
Adjust the striking points of the two beaters
so that they are at equal distances to the left
and right of the center of the head.
Refer to the "KD-12 Owner's Manual" for
details.