Advertisement
104cm
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
SERGIO CHAISE CORNER
ITEM CODE 81190/81191/81192
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Amart Furniture SERGIO 81190
Summary of Contents for Amart Furniture SERGIO 81190
- Page 1 ASSEMBLY INSTRUCTION SERGIO CHAISE CORNER ITEM CODE 81190/81191/81192 Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia. For any assistance with assembly or for missing parts please phone Amart Furniture, Customer Service Free call 1800 351 084 104cm Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia. For any assistance with assembly or for missing parts please phone Amart Furniture, Customer Service Free call 1800 351 084...
-
Page 2: Pre-Assembly Preparation
PRE‐ASSEMBLY PREPARATION Before you start: Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product Take care when lifting. Product should be assembled as near as possible to the point of use Ensure that you have all required contents for complete assembly Always read the assembly instructions carefully before beginning assembly. - Page 3 Step1: Locate the recliner power pack which is fixed on the mechanism at the bottom of left hand facing recliner. Power Parts Connection Transformer cable Transformer Power cable Power Pack Transformer Power cable Transformer cable 1pcs 1pcs 1pcs Step2: Keep back rest in an upright position then slide receivers into steel mechanism posts at seat of the left hand facing recliner, Press both sides of the back firmly into place to ensure it is fully locked. Receiver at bottom of back rest Mechanism post at rear of seat slide receiver into post...
- Page 4 Step3: Carefully locate and remove the Console Sofa Feet and the Console Power Cord from the zipper underneath the Console piece. Keep the Console Power Cord to the side, keeping note this is for the console. Plastic foot Console Power Cord 4pcs 1pcs Step4: Screw the 4 x Console Feet into the pre‐drilled holes in the botom of the console by turning them in a clockwise direction to tighten. Turn the plastic round feet clockwise to tighten...
- Page 5 Step5: Locate the recliner power pack which is fixed on the mechanism at the bottom of armless recliner. Power Parts Connection Transformer Power cable Power Pack Transformer Power cable 1pcs 1pcs Step6: Keep back rest in an upright position then slide receivers into steel mechanism posts at seat of the Armless Recliner, Press both sides of the back firmly into place to ensure it is fully locked. Receiver at bottom of back rest Mechanism post at rear of seat slide receiver into post...
- Page 6 Step7: Carefully locate and remove the Wedge Sofa Feet from the zipper underneath the Wedge piece. Plastic foot 5pcs Step8: Secure the 5 x plastic feet provided to the bottom of the Wedge piece, turning in clockwise direction to tighten. Turn the plastic round feet clockwise to tighten...
- Page 7 Step9: Carefully locate and remove the Armless Chair Sofa Feet from the zipper underneath Armless Chair seat. Plastic foot 4pcs Step10: Secure the 4 x plastic feet provided onto each corner of the Armless Chair Seat by placing the feet in the pre‐drilled holes and turning the feet in a clockwise direction to tighten. Turn the plastic round feet clockwise to tighten...
- Page 8 Step11: Carefully locate and remove the Sofa Feet and Power Cord from the zipper underneath the Armless Chair with drop‐down table piece. Keep the Power Cord to the side, keeping note this is for the Armless Chair with drop‐ down table. Plastic foot Console Power Cord 4pcs 1pcs Step12: Secure the 4 x plastic feet provided onto each corner of the Armless Chair Seat by placing the feet in the pre‐drilled holes and turning the feet in a clockwise direction to tighten. Turn the plastic round feet clockwise to tighten...
- Page 9 Step13: Locate and remove the right hand facing chaise sofa feet box that is placed inside the zipper pocket underneath the chaise seat. Using the M8X60 bolts and washers, screw the sqaured feet into the pre‐drilled holes in each corner at bottom of the chaise using a screwdriver. Bolt M8X60 Washer 5pcs 5pcs Support foot Side foot 1pcs 5pcs Arm Side Step14: Screw rounded supporting chaise foot into the middle pre‐drilled hole by turning the foot in a clockwise direction to tighten. Armless Side Arm Side Turn the support leg clockwise tighten. ...
-
Page 10: Safety Note
Step15: Connect 7 pieces from right to left. Begin with the right hand facing chaise, then armless chairs, then wedge seat, then armless recliner, then console, then left hand facing recliner. Slide the base clips together then press the front and rear sides to ensure the clips are connected all the way to the bottom. *Note: the armless chairs and console can be swapped around.* Left Right 7th PCS 1st PCS Step16: Plug the left hand facing recliner power pack (refer to step 1) into the back socket of the left hand facing recliner. SAFETY NOTE: PLEASE ENSURE THAT ALL ELECTRICAL CORDS AND CABLES ARE CLEAR OF THE FRAME AND MECHANISM. A FAILURE TO DO SO MAY SEVER YOUR POWER CORD RESULTING IN SERIOUS INJURY OR DEATH. - Page 11 Step17: Plug console power cord into the socket at the back panel of console. SAFETY NOTE: PLEASE ENSURE THAT ALL ELECTRICAL CORDS AND CABLES ARE CLEAR OF THE FRAME AND MECHANISM. A FAILURE TO DO SO MAY SEVER YOUR POWER CORD RESULTING IN SERIOUS INJURY OR DEATH. Step18: Connect Armless recliner power pack (refer to step 5) with the plug covered by back flip. SAFETY NOTE: PLEASE ENSURE THAT ALL ELECTRICAL CORDS AND CABLES ARE CLEAR OF THE FRAME AND MECHANISM. A FAILURE TO DO SO MAY SEVER YOUR POWER CORD RESULTING IN SERIOUS INJURY OR DEATH.
- Page 12 Step19: Plug power cord into the socket at the back panel of Armless Chair with drop‐down table piece. SAFETY NOTE: PLEASE ENSURE THAT ALL ELECTRICAL CORDS AND CABLES ARE CLEAR OF THE FRAME AND MECHANISM. A FAILURE TO DO SO MAY SEVER YOUR POWER CORD RESULTING IN SERIOUS INJURY OR DEATH.
-
Page 14: Care And Maintenance
CARE AND MAINTENANCE FABRIC CARE REGULAR CARE: PROTECT FROM DIRECT SUNLIGHT. VACUUM REGULARLY USING LOW SUCTION. ROTATE REVERSIBLE CUSHIONS REGULARLY. CLEANING: DO NOT REMOVE CUSHION COVERS FOR SEPARATE CLEANING EVEN THOUGH THEY HAVE ZIPPERS. DO NOT WASH DO NOT DRY CLEAN DO NOT SHAMPOO CLEAN CLEAN WITH HOT‐WATER EXTRACTION MACHINE. (HOT) PROFESSIONAL CLEANING RECOMMENDED. DO NOT USE DISHWASHING OR LAUNDRY DETERGENTS. USE ONLY UPHOLSTERY DETERGENTS DO NOT WET FILLING DRY IN SHADE AWAY FROM DIRECT HEAT AND SUNLIGHT ALLOW TO DRY THOROUGHLY BEFORE RE‐USE SPOT CLEANING: DO NOT RUB DO NOT SPOT CLEAN WITH ANY SOLVENT. TREAT SPILLS AND STAINS AS SOON AS POSSIBLE. GENTLY SCRAPE ANY SOIL OR MOP ANY LIQUID FROM THE SURFACE OF THE FABRIC. APPLY PROPREITARY CLEANING AGENTS STRICTLY ACCORDING TO INSTRUCTIONS TO REMOVE THE RESIDUE OF THE SPILL. DO NOT SATURATE THE FABRIC OR INTERIOR WITH WATER OR OTHER CLEANING LIQUIDS. WARNING: APPLY ONLY WATER‐BASED SOIL RESIST (FABRIC PROTECTION) TREATMENTS. DO NOT USE AEROSOL PRODUCTS.
Need help?
Do you have a question about the SERGIO 81190 and is the answer not in the manual?
Questions and answers