Operating Video Components - JVC RX-DP15BC Instructions Manual

Audio/video control receiver
Hide thumbs Also See for RX-DP15BC:
Table of Contents

Advertisement

Operating Video Components

IMPORTANT:
To operate JVC's video components using this remote control:
• You need to connect JVC's video components through the AV
COMPU LINK jacks (see page 68) in addition to the connections
using cables with RCA pin plugs (see pages 13 to 15).
• Some JVC VCRs can accept two types of control signals—remote
codes "A" and "B." Before using this remote control, make sure that
the remote control code of the VCR connected to the VCR 1 IN
jacks is set to code "A."
– When another JVC VCR is connected to the VCR 2 IN and VIDEO
jacks, set its remote control code to code "B." (This remote control
cannot emit the control signals of code "B.")
• To operate the video component(s) using the remote control:
– Aim the remote control directly at the remote sensor on each
component, not on the receiver.
• To operate the video component(s) using the RF signals emitted
from this remote control, the IR signal transmitter and the RF rod
antenna must be connected to this receiver.
– Place the IR signal transmitter so that it is aimed at the remote
sensor(s) on the target video component(s).
– The RF signal-reachable distance may differ depending on the
operating conditions and circumstances.
– The IR signal transmitter can send signals from a distance of 3 m.
When using the remote control:
– Set the ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector to "ZONE 1"
or "ZONE 2" correctly.
LEARN
TRANSMIT
ZONE 1
ZONE 2
– Set the TV operation mode selector to "TV" or
"CATV/DBS" properly.
To operate TV, set it to "TV."
– Check the indication shown on the remote's display
when you press a button—this indicates the remote
control operation mode together with multi-room operation mode
(either ZONE 1 or ZONE 2) for a while.
– The CONTROL button can change the remote control operation
mode without changing the source.
Each time you press the button, the remote control operation mode
changes in the sequence—VCR1 = TAPE = CDR = CD DISC = (back
to the beginning).
LEARN
TRANSMIT
STANDBY
ON
ZONE 1
ZONE 2
ZONE 1
ZONE 2
TV/CATV/DBS
VCR 1
ON/OFF
ON/OFF
STANDBY/ON
STANDBY/ON
ZONE 1
Ex. When you press VCR1
with ZONE 1/ZONE 2
(LEARN/TRANSMIT)
selector set to "ZONE 1."
73
LEARN
TRANSMIT
ZONE 1
ZONE 2
TV
CATV/
DBS
LEARN
TRANSMIT
STANDBY
ON
ZONE 1
ZONE 2
ZONE 1
ZONE 2
TV/CATV/DBS
VCR 1
ON/OFF
ON/OFF
STANDBY/ON
STANDBY/ON
ZONE 2
Ex. When you press VCR1
with ZONE 1/ZONE 2
(LEARN/TRANSMIT)
selector set to "ZONE 2."
VCR (VCR connected to the VCR 1 jacks)
You can always perform the following operations:
VCR 1
(STANDBY/ON): Turns on or off the VCR.
After pressing VCR 1 or selecting "VCR1" by pressing CONTROL
repeatedly, you can perform the following operations on the VCR:
1 – 9, 0
: Selects the TV channels on the VCR.
PLAY
: Starts playing.
REW
: Rewinds a tape.
FF
: Fast-winds a tape.
STOP
: Stops operations.
PAUSE
: Pauses playing. To release, press PLAY.
¶ REC
: Press this button together with the PLAY button
to start recording (only for Zone 1 operations).
Press this button together with the PAUSE button
to enter recording pause (only for Zone 1
operations).
CHANNEL +/– : Changes the TV channels on the VCR.
DVD player
After pressing DVD (or DVD MULTI: only for Zone 1 operations),
you can perform the following operations on the DVD player:
1 – 10, 0, +10 : Selects the DVD titles or the chapters.
PLAY
: Starts playing.
4
: Returns to the beginning of the current (or
previous) chapter.
¢
: Skips to the beginning of the next chapter.
STOP
: Stops playing.
PAUSE
: Stops playing temporarily. To release, press
PLAY.
After pressing DVD MENU, these
buttons can be used for the DVD
menu operations.
Note:
Refer also to the manual supplied for your DVD player (and the
instruction supplied for the discs).
TV
You can always perform the following operations (with the TV
operation mode selector set to "TV"):
TV/CATV/DBS
(STANDBY/ON)
: Turns on or off the TV.
TV VOL +/–
: Adjusts the volume.
TV/VIDEO
: Sets the input mode (either TV or VIDEO).
After pressing TV/DBS (with the TV operation mode selector set to
"TV"), you can perform the following operations on a TV:
CHANNEL +/– : Changes the channels.
1 – 9, 0, 100+ : Selects the channels.
RETURN
: Alternates between the previously selected
channel and the current channel.
SET
DVD
MENU

Advertisement

Table of Contents
loading

This manual is also suitable for:

Rx-dp15bjRx-dp15b

Table of Contents