Asus AAEON SRG-AM62 User Manual
Asus AAEON SRG-AM62 User Manual

Asus AAEON SRG-AM62 User Manual

Iot gateway system
Table of Contents

Advertisement

Quick Links

SRG-AM62
IoT Gateway System
st
User's Manual 1
Ed
Last Updated: August 12, 2024

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AAEON SRG-AM62 and is the answer not in the manual?

Questions and answers

Summary of Contents for Asus AAEON SRG-AM62

  • Page 1 SRG-AM62 IoT Gateway System User’s Manual 1 Last Updated: August 12, 2024...
  • Page 2: Copyright Notice

    Copyright Notice This document is copyrighted, 2024. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer.
  • Page 3 Acknowledgement All other products’ name or trademarks are properties of their respective owners. Microsoft Windows® is a registered trademark of Microsoft Corp. ⚫ Texas Instruments™ and Sitara™ are trademarks of Texas Instruments ⚫ Arm® and Cortex® are registered trademarks of Arm Limited (or its ⚫...
  • Page 4 Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity SRG-AM62 ⚫ 2-pin 3.81mm Power Terminal Block w/Lock ⚫ 14-pin 2.54mm Phoenix plug in Connector/Lock ⚫ If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
  • Page 5 About this Document This User’s Manual contains all the essential information, such as detailed descriptions and explanations on the product’s hardware and software features (if any), its specifications, dimensions, jumper/connector settings/definitions, and driver installation instructions (if any), to facilitate users in setting up their product. Users may refer to the product page on AAEON.com for the latest version of this document.
  • Page 6 Safety Precautions Please read the following safety instructions carefully. It is advised that you keep this manual for future references All cautions and warnings on the device should be noted. Make sure the power source matches the power rating of the device. Position the power cord so that people cannot step on it.
  • Page 7 If any of the following situations arises, please the contact our service personnel: Damaged power cord or plug Liquid intrusion to the device iii. Exposure to moisture Device is not working as expected or in a manner as described in this manual The device is dropped or damaged Any obvious signs of damage displayed on the device...
  • Page 8 FCC Statement This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
  • Page 9 China RoHS Requirements (CN) 产品中有毒有害物质或元素名称及含量 AAEON System QO4-381 Rev.A0 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) 醚(PBDE) 印刷电路板 × ○ ○ ○ ○ ○ 及其电子组件 外部信号 × ○ ○ ○ ○ ○ 连接器及线材 外壳 ○...
  • Page 10 China RoHS Requirement (EN) Hazardous and Toxic Materials List AAEON System QO4-381 Rev.A0 Hazardous or Toxic Materials or Elements Component Name PCB and Components Wires & Connectors for Ext.Connections Chassis CPU & RAM HDD Drive LCD Module Optical Drive Touch Control Module Battery This form is prepared in compliance with the provisions of SJ/T 11364.
  • Page 11: Table Of Contents

    Table of Contents Chapter 1 - Product Specifications..................1 Specifications........................ 2 Function Block Diagram ..................... 4 Chapter 2 – Hardware Information ..................5 Dimensions ........................6 Jumpers and Connectors ..................8 List of Jumpers ......................10 2.3.1 LVDS VDD Power Selection (JP5 Pins 1, 3, 5) ..........10 2.3.2 LVDS Backlight Power Selection (JP5 Pins 2, 4, 6) ........
  • Page 12 2.4.16 USB 2.0 Port 1/Port 2 (CN142) ............... 29 2.4.17 RJ-45 LAN Port 1/Port 2 (CN145) ..............30 Chapter 3 - Product Setup and Configuration..............31 System Account Management ................32 3.1.1 Debug Console ....................32 3.1.2 Log In ........................37 I/O Control Command and Example ..............
  • Page 13 3.2.10.1 Enable LVDS Panel................... 47 3.2.10.2 Disable LVDS Panel.................. 47 3.2.11 LED Control ....................... 47 3.2.12 Watchdog Control (TPS3431SDRBR) ............48 3.2.12.1 Feed Dog Example Code ............... 48 3.2.12.2 Enable/Disable Watchdog ..............48 3.2.13 Unsupported Features ..................48 Wireless Control Command and Example ............49 3.3.1 CN12 4G SIM Card Module (EG25-G) ............
  • Page 14: Chapter 1 - Product Specifications

    Chapter 1 Chapter 1 - Product Specifications...
  • Page 15: Specifications

    Specifications System Processor Texas Instruments™ AM625/AM623 Sitara™ Quad-Core Arm® Cortex®-A53, 1.4 GHz Memory Type Onboard DDR4, up to 4GB Power Requirement DC 9V ~ 36V (Optional: 12V) Board Dimension 2.8” x 3.9” (72mm x 100mm) System Dimension 4.25" x 3.13" x 1.29" (108mm x 79.5mm x 33mm) Operating Temperature -40°F ~ 185°F (-40°C ~ 85°C) Optional:...
  • Page 16 Indicator Indicator Programmable LED Control x 3 Internal I/O Storage eMMC 5.1, 16GB (Optional: 32GB/64GB/128GB) TPM 2.0 (Optional) External I/O Ethernet Gigabit Ethernet x 2 (integrated RGMII) Audio Line Out x 1/Line In x 1/Mic In x 1 (by request) USB Port USB 2.0 x 2 (Host/Device by Image option x 1, default: Host, Host x...
  • Page 17: Function Block Diagram

    Function Block Diagram Chapter 1 – Product Specifications...
  • Page 18: Chapter 2 - Hardware Information

    Chapter 2 Chapter 2 – Hardware Information...
  • Page 19: Dimensions

    Dimensions System Chapter 2 – Hardware Information...
  • Page 20 Board Chapter 2 – Hardware Information...
  • Page 21: Jumpers And Connectors

    Jumpers and Connectors Component Side Chapter 2 – Hardware Information...
  • Page 22 Solder Side Chapter 2 – Hardware Information...
  • Page 23: List Of Jumpers

    List of Jumpers Jumpers allow users to manually customize system configurations to their suitable application needs. Please refer to the table below for all of the board’s jumpers that you can configure for your application Label Function JP5 (Pins 1, 3, 5) LVDS VDD Power Selection JP5 (Pins 2, 4, 6) LVDS Backlight Power Selection...
  • Page 24: Boot Selection (Jp6 Pins 2, 4, 6)

    2.3.3 Boot Selection (JP6 Pins 2, 4, 6) Chapter 2 – Hardware Information...
  • Page 25: List Of Connectors

    List of Connectors Please refer to the table below for all of the board’s connectors that you can configure for your application Label Function DC Power SPI/I2C/GPIO Connector CN12 Full-size Mini Card Slot CN13 Half-size Mini Card Slot CN14 RTC Battery Connector CN16 Micro SD Slot CN25...
  • Page 26: Dc Power (Cn1)

    2.4.1 DC Power (CN1) Pin Name Signal Type Signal Level DC_IN +9~36V / +12V Note 1: Wide range input voltage from +9V to +36V or +12V for specified version. Note 2: Please check the input voltage description on product label before inserting power.
  • Page 27: Full-Size Mini Card Slot (Cn12)

    Pin Name Signal Type Signal Level SPI0_CS0 +3.3V GPIO_16 +3.3V Note: Pitch = 1.27mm. 2.4.3 Full-size Mini Card Slot (CN12) Pin Name Signal Type Signal Level +3.3VSB +3.3V Chapter 2 – Hardware Information...
  • Page 28 Pin Name Signal Type Signal Level W_DISABLE1# (Note 1) +3.3V PERST1# +3.3V UART_TX +3.3V +3.3VSB +3.3V SMB1_CLK (Note 1) +3.3V UART_RX +3.3V SMB1_DATA (Note 1) +3.3V USB1_D- DIFF USB1_D+ DIFF +3.3VSB +3.3V +3.3VSB +3.3V Chapter 2 – Hardware Information...
  • Page 29: Half-Size Mini Card Slot (Cn13)

    Pin Name Signal Type Signal Level +3.3VSB +3.3V Note 1: The function is disabled by unmounted 0ohm jumper. W_DISABLE1#: R3232, SMB1_CLK: R328, SMB1_DATA: R326. Note 2: The driving current supports up to 2A. Note 3: For 4G full-size mini card. 2.4.4 Half-size Mini Card Slot (CN13) Pin Name...
  • Page 30 Pin Name Signal Type Signal Level W_DISABLE2# (Note 1) +3.3V PERST2# +3.3V +3.3VSB +3.3V SMB2_CLK (Note 1) +3.3V SMB2_DATA (Note 1) +3.3V USB2_D- DIFF USB2_D+ DIFF +3.3VSB +3.3V Chapter 2 – Hardware Information...
  • Page 31 Pin Name Signal Type Signal Level +3.3VSB +3.3V +3.3VSB +3.3V Chapter 2 – Hardware Information...
  • Page 32: Rtc Battery Connector (Cn14)

    Note 1: The function is disabled by unmount 0ohm jumper. W_DISABLE2#: R334, SMB2_CLK: R9237, SMB2_DATA: R9236 Note 2: The driving current supports up to 2A. Note 3: For WIFI / BT half-size mini card. 2.4.5 RTC Battery Connector (CN14) Pin Name Signal Type Signal Level +3.3V...
  • Page 33: Lvds Port Inverter/Backlight Connector (Cn25)

    Pin Name Signal Type Signal Level SD_CMD +3.3V SD_VDD +3.3V SD_CLK +3.3V SD_VSS SD_DAT0 +3.3V SD_DAT1 +3.3V 2.4.7 LVDS Port Inverter/Backlight Connector (CN25) Pin Name Signal Type Signal Level LVDS_BKL_ENABLE +3.3V LVDS_BKL_CONTROL LVDS_BLK_PWR +5V / +12V Note 1: LVDS/ LVDS_BLK_PWR can be set to +5V or +12V by JP5. Note 2: The driving current supports up to 2A.
  • Page 34: Lvds Connector (Cn26)

    2.4.8 LVDS Connector (CN26) Pin Name Signal Type Signal Level LVDS_BLK_ENABLE LVDS_BKL_CONTROL LVDS_VDD +3.3V / +5V LVDS_A_CLK- DIFF LVDS_A_CLK+ DIFF LVDS_VDD +3.3V / +5V LVDS_DA0- DIFF LVDS_DA0+ DIFF LVDS_DA1- DIFF LVDS_DA1+ DIFF LVDS_DA2- DIFF LVDS_DA2+ DIFF LVDS_DA3- DIFF LVDS_DA3+ DIFF DDC_DATA +3.3V DDC_CLK...
  • Page 35: Audio Port (Cn27)

    Pin Name Signal Type Signal Level LVDS_DB2- DIFF LVDS_DB2+ DIFF LVDS_DB3- DIFF LVDS_DB3+ DIFF LVDS_VDD +3.3V / +5V LVDS_B_CLK- DIFF LVDS_B_CLK+ DIFF Note 1: LVDS/ LVDS_VDD can be set to +3.3V or +5V by JP5. Note 2: The driving current supports up to 2A. 2.4.9 Audio Port (CN27) Pin Name...
  • Page 36: Debug Port (Cn30)

    Pin Name Signal Type Signal Level LINE_R_IN +3.3V +VDD_AUDIO +3.3V LINE_L_IN +3.3V 2.4.10 Debug Port (CN30) Pin Name Signal Type Signal Level +5VSB USB0_DN DIFF USB0_DP DIFF USB0_ID 3.3V Note: USB to UART (XR21V1410) debug port. Chapter 2 – Hardware Information...
  • Page 37: Com Port 1/Port 2 (Rs-232/422/485) (Cn70)

    2.4.11 COM Port 1/Port 2 (RS-232/422/485) (CN70) Pin Name Signal Type Signal Level ±9V / ±5V ±9V / ±5V DCD1 ±9V / ±5V DTR1 ±9V / ±5V CAN1_H / RST1 DIFF / OUT DIFF / ±9V / ±5V CAN1_L / CTS1 DIFF / IN DIFF / ±9V / ±5V ±9V / ±5V...
  • Page 38 COM Port 1 RS-485 Pin Name Signal Type Signal Level RS485_D- ±9V / ±5V RS485_D+ ±9V / ±5V COM Port 2 RS-422 Pin Name Signal Type Signal Level RS422_TX- ±9V / ±5V RS422_TX+ ±9V / ±5V RS422_RX+ ±9V / ±5V RS422_RX- ±9V / ±5V COM Port 2 RS-485...
  • Page 39: Com Port 3 (Rs-232/422/485) (Cn71)

    2.4.12 COM Port 3 (RS-232/422/485) (CN71) Pin Name Signal Type Signal Level DCD3 ±9V / ±5V ±9V / ±5V ±9V / ±5V DTR3 ±9V / ±5V DSR3 ±9V / ±5V RTS3 ±9V / ±5V CTS3 ±9V / ±5V ±9V / ±5V 2.4.13 COM Port 4 (RS-232/422/485) (CN72) Pin Name...
  • Page 40: Internal Usb 2.0 Port (Cn94)

    Pin Name Signal Type Signal Level DGND DSR4 ±9V / ±5V RTS4 ±9V / ±5V CTS4 ±9V / ±5V ±9V / ±5V 2.4.14 Internal USB 2.0 Port (CN94) Pin Name Signal Type Signal Level +5VSB USB3_DN DIFF USB3_DP DIFF Note: The driving current supports up to 2A. Chapter 2 –...
  • Page 41: Hdmi Port (Cn141)

    2.4.15 HDMI Port (CN141) Pin Name Signal Type Signal Level HDMI_TX2+ DIFF HDMI_TX2- DIFF HDMI_TX1+ DIFF HDMI_TX1- DIFF HDMI_TX0+ DIFF HDMI_TX0- DIFF HDMI_CLK+ DIFF HDMI_CLK- DIFF HDMI_CEC +3.3V HDMI_Utility +1,8V DDC_CLK DDC_DATA +V5S HDMI_HPD +1.8V Chapter 2 – Hardware Information...
  • Page 42: Usb 2.0 Port 1/Port 2 (Cn142)

    2.4.16 USB 2.0 Port 1/Port 2 (CN142) Pin Name Signal Type Signal Level +5VSB USB1_DN DIFF USB1_DP DIFF +5VSB USB2_DN DIFF USB2_DP DIFF Note 1: The driving current supports up to 2A. Chapter 2 – Hardware Information...
  • Page 43: Lan Port 1/Port 2 (Cn145)

    2.4.17 RJ-45 LAN Port 1/Port 2 (CN145) Pin Name Signal Type Signal Level LAN1_MDI0_P DIFF LAN1_MDI0_N DIFF LAN1_MDI1_P DIFF LAN1_MDI1_N DIFF LAN1_MDI2_P DIFF LAN1_MDI2_N DIFF LAN1_MDI3_P DIFF L_10 LAN1_MDI3_N DIFF LAN2_MDI0_P DIFF LAN2_MDI0_N DIFF LAN2_MDI1_P DIFF LAN2_MDI1_N DIFF LAN2_MDI2_P DIFF LAN2_MDI2_N DIFF LAN2_MDI3_P...
  • Page 44: Chapter 3 - Product Setup And Configuration

    Chapter 3 Chapter 3 - Product Setup and Configuration...
  • Page 45: System Account Management

    System Account Management 3.1.1 Debug Console When connecting a PC or laptop to the SRG/PICO-AM62, using PuTTY with Windows 10 is recommended. Users can download the software from the PuTTY website: Step 1: Download the PuTTY tools: https://www.putty.org/. Step 2: Set jumper (JP5) to 3-5 2-6 (default settings). Step 3: Set jumper (JP6) to 4-6 (default settings).
  • Page 46 Step 7: Open Device Manager and install xr21v1410 driver. Chapter 3 – Product Setup and Configuration...
  • Page 47 Chapter 3 – Product Setup and Configuration...
  • Page 48 Chapter 3 – Product Setup and Configuration...
  • Page 49 Step 8: Reboot your Windows PC and check COM port name. Step 9: Open PuTTY on pc and set COM port info Chapter 3 – Product Setup and Configuration...
  • Page 50: Log In

    3.1.2 Log In Log into the system using the below credentials. Login Settings Username root Password Pw#12345 I/O Control Command and Example 3.2.1 CN70: COM 1~COM 6 & CAN FD 1~2 Please refer to section 2.4.11 COM Port 1/Port 2 (RS 232/422/485) (CN70). 3.2.2 CAN FD Command example (can0 ->...
  • Page 51: Com 1~Com 4 Rs-232/422/485 & Com 5-Com 6 Ttl

    Result: 3.2.3 COM 1~COM 4 RS-232/422/485 & COM 5-COM 6 TTL 3.2.3.1 Mode Setting Table For COM 1 ~ COM 4 to work on F81439 (TTL to RS-232/422/485 transceiver), it must be set as follows: gpio high/low to switch signal modes. RS-485 RS-485 RS-232...
  • Page 52: Device Name Table

    COM 1 COM 2 COM 3 COM 4 Mode Pin 1 gpioset 1 gpioset 1 gpioset 0 gpioset 2 43=0/1 38=0/1 23=0/1 22=0/1 Mode Pin 2 gpioset 1 gpioset 1 gpioset 1 gpioset 2 41=0/1 40=0/1 33=0/1 30=0/1 Mode Pin 3 gpioset 1 gpioset 1 gpioset 1...
  • Page 53: Com 1 To Com 2 Using Rs-485 Mode (Python)

    3.2.3.3 COM 1 to COM 2 Using RS-485 Mode (Python) Command: python3 import serial comA = serial.Serial("/dev/ttyS3", 115200, timeout=1) comB = serial.Serial("/dev/ttyS7", 115200, timeout=1) data_len = comA.write(b'test string') data = comB.read(data_len) print(data) comA.close() comB.close() 3.2.4 CN71/CN72 RS-232/422/485 Please refer to section 2.4.12 COM Port 3 (RS-232/422/485) (CN71) and 2.4.13 COM Port 4 (RS-232/422/485) (CN72).
  • Page 54: Audio Settings

    3.2.5 Audio Settings Step 1: Open PulseAudio Volume Control app. Step 2: To switch the output to CN27 Audio or HDMI Audio, use the list on the right side of the music playback item. Chapter 3 – Product Setup and Configuration...
  • Page 55: Cautions

    The audio loopback function On/Off button allows you to loopback line in/mic in to line out. 3.2.5.1 Cautions You must initialize the graphics at boot time if you want to use the GUI interface software. If you connect the AM62 platform to the screen using an HDMI cable after it has already booted, you will have missed the initialization opportunity, and you won't see any GUI on the screen.
  • Page 56: Custom Button

    3.2.6 Custom Button Default function: Press SW2 for 5 seconds and the machine will reboot. You can edit the following script file to modify the functionality of this button. /usr/sbin/sw_gpio.sh 3.2.7 I2C/SPI/GPIO Interface (CN4) 3.2.7.1 CN4 Pin Define Table Please refer to section 2.4.2 SPI/I2C/GPIO Connector (CN4). 3.2.7.2 I2C Command Example Check the I2C device slave address on the bus (0x68).
  • Page 57: Spi Command Example

    3.2.7.3 SPI Command Example Recommended spi-pipe version: 1.0.2. Send \x90\x00\x00\x00\xFF\xFF to the SPI device with CS0. Command: printf '\x90\x00\x00\x00\xFF\xFF' | spi-pipe -d /dev/spidev1.0 -s 24000000 -b 6 -n 1 |hexdump -C 3.2.7.4 GPIO Command Example (gpio1_16) Command: gpioset 2 16=1 #high 3.3V gpioset 2 16=0 #low 0V 3.2.8 RTC (External and CPU Internal)
  • Page 58: Internal Rtc

    3.2.8.2 Internal RTC Command: hwclock -f /dev/rtc1 Result: 3.2.8.3 System Time Command: date Result: Chapter 3 – Product Setup and Configuration...
  • Page 59: Tpm (Npct75X)

    3.2.9 TPM (NPCT75x) Command: tpm2_selftest tpm2_getcap properties-fixed Result: Chapter 3 – Product Setup and Configuration...
  • Page 60: Lvds Panel Enable/Disable

    3.2.10 LVDS Panel Enable/Disable 3.2.10.1 Enable LVDS Panel Command: set_lvds_to_156_inches_panel.sh reboot Result: 3.2.10.2 Disable LVDS Panel Command: set_lvds_disable.sh reboot Result: 3.2.11 LED Control Command LED1 Power LED2 ON: gpioset 1 3=1 OFF: gpioset 1 3=0 LED3 ON: gpioset 1 4=1 OFF: gpioset 1 4=0 LED4 ON: gpioset 1 5=1...
  • Page 61: Watchdog Control (Tps3431Sdrbr)

    3.2.12 Watchdog Control (TPS3431SDRBR) 3.2.12.1 Feed Dog Example Code This code runs automatically at boot. If the dog is not fed within 77 seconds, the product will reset. The following example code will auto run by kernel aaeon.service Code path: /usr/sbin/hw_wdt_gpio.sh 3.2.12.2 Enable/Disable Watchdog...
  • Page 62: Wireless Control Command And Example

    Wireless Control Command and Example 3.3.1 CN12 4G SIM Card Module (EG25-G) Power on Mini Card (default: on) Command: gpioset 2 25=0 Result: Open wwan0 Tool: https://github.com/kmilo17pet/quectel-cm Command: /usr/sbin/quectel-cm/quectel-CM & Chapter 3 – Product Setup and Configuration...
  • Page 63: Cn13 Mini Card Bluetooth (Wpet-239Acn(Bt))

    Result: 3.3.2 CN13 Mini Card Bluetooth (WPET-239ACN(BT)) Power on Mini Card (default: on) Command: gpioset 2 25=0 Chapter 3 – Product Setup and Configuration...
  • Page 64 Result: Command to pair, connect Command: bluetoothctl power on agent off agent NoInputNoOutput default-agent pairable on Chapter 3 – Product Setup and Configuration...
  • Page 65 Scan on Please find the MAC address of the device to connect to in the log after scanning Pair <mac> Command: pair F4:73:35:75:CF:7B Chapter 3 – Product Setup and Configuration...
  • Page 66: Cn13 Mini Card Wi-Fi (Wpet-239Acn(Bt))

    Connect <mac> Command: connect F4:73:35:75:CF:7B Command: trust F4:73:35:75:CF:7B exit 3.3.3 CN13 Mini Card Wi-Fi (WPET-239ACN(BT)) Power on Mini Card (default: on) Command: gpioset 2 25=0 Result: Chapter 3 – Product Setup and Configuration...
  • Page 67 Open wlan0 Command: ifconfig wlan0 up Chapter 3 – Product Setup and Configuration...
  • Page 68 Result: Scan Wi-Fi name Command: iw wlan0 scan | grep 'AAEON-Wireless'(your WiFi name) Result: Save Wi-Fi name/password Command: wpa_passphrase AAEON-Wireless >> /tmp/wpa_wifi.conf Result: Initial Wi-Fi configuration Command: wpa_supplicant -B -i wlan0 -c /tmp/wpa_wifi.conf root Result: Chapter 3 – Product Setup and Configuration...
  • Page 69: Cn12 & Cn13 Mini Card Power On/Off Pin Control

    Link Wi-Fi Command: iw wlan0 link dhclient wlan0 Result: 3.3.4 CN12 & CN13 Mini Card Power On/Off Pin Control Power On Power Off gpioset 2 25=0 gpioset 2 25=1 3.3.5 CN12 & CN13 Pin 22 PERST# High/Low Pin Control Connector PERST# High PERST# Low CN12...
  • Page 70: Os Installation

    OS Installation 3.4.1 Flash SD Card Step 1: Use balenaEtcher to flash boot image to SD card. Step 2: Press SW2 and connect the power supply to start up the SD Card boot. Step 3: Flash eMMC Card - After booting with the SD Card, use the following commands to flash the image to the eMMC.
  • Page 71: Sd Card/Emmc Boot Mode

    Result: Please power up the pico-am62 again and boot using EMMC mode. 3.4.2 SD Card/EMMC Boot Mode Use SW2 status to choose SD Card/EMMC boot mode. SD Card Boot Mode eMMC Boot Mode Press SW2 Do not press SW2 Chapter 3 – Product Setup and Configuration...
  • Page 72: Check Os Version

    3.4.3 Check OS Version Command: cat /etc/aaeon-release Result: Chapter 3 – Product Setup and Configuration...
  • Page 73: Appendix A - Mating Connectors

    Appendix A Appendix A – Mating Connectors...
  • Page 74: List Of Mating Connectors And Cables

    List of Mating Connectors and Cables The following table lists mating connectors and available cables. Mating Connector Conn Available Function Cable P/N Label Vendor Model No. Cable DC Power DINKLE ECH381RM-02P-BK N/A SPI/I2C/GPIO Connector PINREX 232-92-04GBEM 4G Full-Size Mini Card 4G Module CN12 Quectel...

Table of Contents