Specifications - Harman Kardon DPR 1001 Service Manual

Digital path audio/video receiver
Hide thumbs Also See for DPR 1001:
Table of Contents

Advertisement

Available languages

Available languages

AVR1001
DPR1001

SPECIFICATIONS

S/N RATIO,IHF-A
6
FILTER
Should be met by
8CH DIRECTInputs
Should be met by
8
CH DIRECTInputs
Should be met by
all Analog Stereo
Inputs
CHANNEL
Should be met by
SEPARATION:
all Analog Stereo
7
Zterm =
and 8 CH DIRECT
1KW/1000pF
Inputs
IHF-A FILTER
All Analog Stereo
and 8 CH DIRECT
Inputs
FUNCTION
CROSSTALK,
All Analog Stereo
8
(Measured on all
and 8 CH DIRECT
Channels)
Inputs
IHF-A FILTER
AM/FM Tuner
Input
8 CH DIRECT
8 CH DIRECT
Inputs
Inputs
FREQUENCY
FREQUENCY
9
9
RESPONSE
RESPONSE
All Analog Stereo
All Analog Stereo
Inputs
Inputs
CD
POWER
10
BANDWIDTH -
3dB
8 CH DIRECT
Inputs
Referred to 1W Out.Vol at max, all inputs terminatedw/
1kHz
1 Kohm. Should be measured with a 10 Hz-22 KHz BW,
Referred to Rated Output Power, Vol at max, all inputs
1kHz
left un-terminated. Should be measured with
a 10Hz-22 KHz BW, RMS noise reading
Referred to Rated Output Power, Vol at max, all inputs
1kHz
left un-terminated. Should be measured with
a 10Hz-22 KHz BW, RMS noise reading
Vol at Max, Gen amplitude adjusted to obtain R/O-3dB,
measured w/ AP's Xtalk mode. Driving every channel
100Hz
individually. Undriven channels should be terminated
w/1 kOhm.Use 10Hz-22KHz BW
Vol at Max, Gen amplitude adjusted to obtain R/O-3dB,
measured w/ AP's Xtalk mode. Driving every channel
1kHz
individually. Undriven channels should be terminated
w/ 1 kOhm.Use 10Hz-22KHz BW
Vol at Max, Gen amplitude adjusted to obtain R/O-3dB,
measured w/ AP's Xtalk mode. Driving every channel
10kHz
individually. Undriven channels should be terminated
w/ 1 kOhm.Use 10Hz-22KHz BW
Volume at Max. Apply Sinewave Signal Gen amplitude
to the tested input, to obtain R/O-3dB at the speaker
outputs.Record the output level as the reference output.
1 kHz
Then, scroll thru the other possible stereo inputs, and
measure the output level. Compute t
Volume at Max. Apply Sinewave Signal Gen amplitude
to the tested input, to obtain R/O-3dB at the speaker
10 kHz
outputs. Record the FL and FR speaker output level as
the reference output. Scroll thru other stereo inputs,
and measure the output level. Compute th
Apply an FM Stereo RF input thru a 50->75 ohm
dummy antenna (98 MHz carrier, 75 KHz modulation,
1 KHz tone, 72 dBuV level). Then set UUT to FM Stereo,
1 KHz
98 MHz. Set Volume control to 10 dB below Max.
Record the FL and FR speaker output level as the refere
To find the point in
To find the point in
the Frequency
the Frequency
Should be met with Volume at Max (50 mV input) Use
Response Curve,
Response Curve,
Should be met with Volume at Max (50 mV input) Use
where Output Level
where Output Level
falls by 3 dB,
falls by 3 dB,
referred to the 1
referred to the 1
To find the point in
To find the point in
the Frequency
the Frequency
Response Curve,
Response Curve,
Should be met with Volume at Max (50 mV input), and
Should be met with Volume at Max (50 mV input), and
where Output Level
where Output Level
also with Volume at 40 dB below Max (5 V input).
also with Volume at 40 dB below Max (5 V input).
falls by 3 dB,
falls by 3 dB,
referred to the 1
KHz point.
Tested at Stereo
Tested in Stereo Mode, at Stereo Rated Power -3dB.
Mode Rated Power
Find the Input Sinawave Frequency Point where THD
-3dB --> THD
increases to 0.6% . Record the Frequency.
0.6%
Tested at 8 CH
Tested in 8 CH DIRECT Mode, at 8CH DIRECT Rated
DIRECT Mode
Power -3dB. Find the Input Sinawave Frequency Point
Rated Power -3dB
where THD increases to 0.6% . Record the Frequency.
--> THD 0.6%
RMS noise reading
10Hz-500KHz BW
10Hz-500KHz BW
harman/kardon
dB
>55
>60
dB
>70
>75
dB
>80
>85
dB
>55
>60
dB
>60
>65
dB
>50
>60
dB
>70
>75
dB
> 55
>75
dB
> 75
>85
20 Hz-
20 Hz-
Hz
10 Hz-20 kHz
Hz
10 Hz-20 kHz
18K kHz
18K kHz
10 Hz-20
10 Hz-20
Hz
5 Hz-22 kHz
Hz
5 Hz-22 kHz
kHz
kHz
Hz~kHz
20-20kHz
20-22kHz
Hz~kHz
20-20kHz
20-22kHz
TAPE
CD
VID 1
VID 2
VID 3
VID 4
DVD
8 CH
TAPE
CD
VID 1
VID 2
VID 3
VID 4
DVD
ster eo
8 ch
ster eo
8 ch
ster eo
8 ch
ster eo
8 ch
ster eo
8 ch
Vol.max
Vol.max
input:50
input:50
mV
mV
STER
STER
EO
EO
8CH
8CH
STER
Vol.-40
EO
input:5V
8CH
TAPE
CD
VID 1
VID 2
VID 3
VID 4
DVD
7

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents