Table of Contents Introduction Preset Tuning Changing Devices Safety Information RDS Operation Macro Programming Unpacking RDS Tuning Punch-Through Configuration Front Panel Controls RDS Display Options EzSet Configuration Rear Panel Connections Program Search Renaming Main Remote Control Functions Programming the Remote Resetting the Remote Zone II Remote Control Functions Preprogrammed Code Entry...
With the purchase of a Harman Kardon Dolby Headphone circuitry creates an amazing different one (Audio only) in a second room. DPR 1005 you are about to begin many years of sense of openness with headphones. Two-chan- Complete control over volume is possible with a listening enjoyment.
Verify Line Voltage Before Use the 6/8-channel direct inputs for use potential for safety hazards, place the unit on Your DPR 1005 has been designed for use with with DVD-Audio or SACD players, a firm and level surface. When placing the 220-240-Volt AC current.
Front Panel Controls Main Power Switch Set Button Surround Mode Indicators System Power Control Preset Station Selector Speaker/Channel Input Indicators Power Indicator Button Digital Select Button Headphone Jack Input Source Selector Channel Select Button Surround Mode Group Selector RDS Selector Volume Control Speaker Selector Delay Adjust Selector...
Page 6
Front Panel Controls Surround Mode Selector: Press this RDS Select Button: Press this button to dis- Speaker/Channel Input Indicators: These button to cycle through the individual surround play the various messages that are part of the RDS indicators are multipurpose, indicating either the modes available after the Surround Mode data system of the DPR’s tuner.
Rear Panel Connections AC OUTLETS ~230V/50Hz UNSWITCHED / 100W MAX SWITCHED / 50W MAX AM Antenna Center Speaker Outputs Video 3 Video Inputs FM Antenna Surround Speaker Outputs Video 2 Video Inputs Tape Inputs Switched AC Accessory Outlet Optical Digital Inputs Tape Outputs Unswitched AC Accessory Outlet Coaxial Digital Inputs...
Page 8
Video 1 Audio Inputs: Connect these jacks remote controlled devices. Connect this jack to to the PLAY/OUT audio jacks on a VCR or other the “IR IN” jack on Harman Kardon or other audio or video source. compatible equipment. Video 1 Audio Outputs: Connect these Remote IR Input: If the DPR’s front-panel...
Page 9
Preamp Outputs: Connect these jacks to RS-232 Port: This jack may be used to con- an optional, external power amplifier for appli- trol the DPR 1005 over a bi-directional RS-232 cations where higher power is desired. serial control link to a compatible computer or programmable remote control system.
Main Remote Control Functions Power Off Button IR Transmitter Window LCD Information Display Power On Button Input Selectors AVR Selector AM/FM Tuner Select 6-Channel/8-Channel Direct Input Test Button Sleep Button Surround Mode Selector Night Mode Channel Select Button Dim Button Navigation Button Set Button Digital Select...
Page 11
DPR’s remote is shipped from the factory to oper- remind you that the DPR is still turned on. The to the 6-Channel Direct Inputs or the ate the DPR and most Harman Kardon CD or DVD blue accent lighting inside the volume control 8-Channel Direct Inputs (the input players and cassette decks.
Page 12
Main Remote Control Functions Tuning Up/Down: When the tuner is in use, Stereo Mode Selector: Press this button Delay Select Button: This button selects these buttons will tune up or down through the to select a stereo playback mode. When the but- adjustments to the A/V Sync Delay and the indi- selected frequency band.
Page 13
EzSet function to quickly and accurately the tone mode settings, enabling adjustment of calibrate the DPR 1005’s output levels. When the the bass and treble boost/cut. You may also use button is pressed you will then need to select...
Power Off: When used in the room where Disc Skip: Press this button to change TAPE the DPR is located, press this button to place the discs on compatible Harman Kardon CD or DVD unit in Standby. When it is used in a remote TUNING changers.
Installation and Connections After unpacking the unit, and placing it on a solid 7. Connect the front, center and surround 8. Connections to a subwoofer are normally surface capable of supporting its weight, you will speaker outputs to the respective made via a line level audio connection from the need to make the connections to your audio and speakers.
If the adapter plugs are not labeled in For the connections described above your video video inputs on the DPR 1005, the factory default that way, pay attention to the signal flow direc- device needs RCA (cinch) connectors or/and S-...
Page 17
Installation and Connections Important Note for the Use of Black Black SCART-Cinch Adapters: Figure 1: Yellow Yellow When video sources are connected to the TV SCART/Cinch-Adapter for directly with a SCART cable, specific control playback; signals apart from Audio/Video signals will be signal flow: SCART ¡...
Terminate the wiring at the receiver end to distance from the DPR to the remote room, three a standard RJ-45 jack in compliance with the The DPR 1005 is designed for flexible use with options are available for audio connection: instructions furnished with the A-BUS module.
Installation and Connections The Unswitched outlet will receive power Depending on the specifics of your room Center Front Speaker as long as the unit is plugged into a powered AC acoustics and the type of speakers in use, you outlet and the Main Power Switch is on.
To maintian the unit's safety rating, but particularly with projectors, constant display of DO NOT substitute the power cord for one The DPR 1005 features an advanced memory sys- a static image such as these menus or video game with lower current capacity.
Page 21
23. name is entered, up to a maximum of fourteen channel is in use. The DPR 1005’s Auto Polling characters. When using the full-OSD system to make the feature allows you to avoid losing the audio feed...
System Configuration line gives you the opportunity to pointing to the TONE line on the menu and press If your speakers match the factory default setting select which type of signal is directed to the Navigation Button so that of 8 ohms, no further adjustment is needed, Record Output jacks (associated with the is highlighted in reverse video.
Page 23
System Configuration Notes: as most listeners do not need to have individual- line at the bottom of this menu so • When "Independent" is selected for the speak- ized speaker settings. However, some listeners, that only those inputs where the analog bypass is er settings (see below), they need to be made particularly those with full-range front speakers desired will be routed in this fashion, while other...
Page 24
System Configuration When is selected, with all digital sur- 8. Press the Buttons on the remote to The factory default setting for all speaker posi- round modes low-frequency surround channel select the option that best describes your system. tions is 100Hz. If that setting is acceptable for all sounds will be sent to the Fronts when Sub is channels, then no adjustments are needed and The choices available for the subwoofer position...
System Configuration Since the crossover point commonly used in the 10. When all speaker selections have been made, As an example, in the Figure below, all speakers creation of the LFE channel is 120Hz, we press the Button until the cursor is next are set for “large, ”...
Page 26
Logic 7 mode enables the center channel sound more broadly into the BACK TO MASTER MENU to continue the Harman Kardon’s exclusive Logic 7 processing to left and right channels. A higher number (up to setup process. create fully enveloping, multichannel surround “7”) produces a tighter center channel...
System Configuration On the menu, the selection choices a group. This feature is called A/V Sync Delay; it and then pressing the Set STEREO made with the Buttons on the remote allows you to compensate for delays to the video Button .
Figure 7a Using EzSet • The channel position being adjusted will flash Harman Kardon’s exclusive EzSet remote makes it in the Speaker/Channel Input Indicators To adjust the Night mode setting, make certain . If the test noise is heard from a channel possible to quickly and accurately set the DPR’s...
System Configuration NOTE: The subwoofer output is not adjusted each speaker is connected to the correct output 2. Press the Navigation Button once to when the test tone is in use. To adjust the sub- terminal. change the bottom line of the remote’s LCD woofer output you must use an external source, display to read as shown...
Page 30
System Configuration IMPORTANT NOTE: The Output level adjust- ment made will be effective for all inputs, but only for the actual surround mode selected. To be effective for any other mode select that mode (with any input) and repeat the level adjustment described above.
Logic 7 Cinema Exclusive to Harman Kardon for AV receivers, Logic 7 is an advanced mode that extracts the Delay time not adjustable Logic 7 Music...
Page 32
Operation Surround Mode Chart MODE FEATURES DELAY TIME RANGE DTS Neo:6 Cinema These two modes are available when any analog source is playing to create a six-channel Delay time not adjustable DTS Neo:6 Music surround presentation from conventional Matrix-encoded and traditional Stereo sources. Select the Cinema version of Neo:6 when a program with any type of analog Matrix surround encoding is present.
Operation Basic Operation display will dim to one half brightness when the 6-Channel/8-Channel Direct Input Sleep function is programmed. To cancel the Sleep Once you have completed the setup and configu- • There are two input choices available for use function, press and hold the Sleep Button ration of the DPR, it is simple to operate and with sources such as a DVD-Audio or SACD player...
Dolby Pro scroll through the list of available modes. times until the desired setting ( Logic II Music mode or Harman Kardon’s ) appears in the on-screen Note that the Dolby Digital, Dolby Digital EX, DTS...
DPR. Contact decoder chip, replacing the monolithic digital PCM (Pulse Code Modulation) is the non- com- your Harman Kardon dealer for additional details. filters used in conventional DACs, will enable pressed digital audio system used for compact...
Operation Selecting a Digital Source present, the DPR uses a variety of indicators to let speaker configuration is set to show the presence To utilize either digital mode you must have you know what type of signal is present. This will of subwoofer.
(Matrix decoded with outputs of the source to the DPR 1005, with the NEO:6, LOGIC 7 or 7 CH Stereo), but no letters digital audio input set as the default following inside will light as the unit will not receive an the steps shown on page 21.
Figure 10 In addition to the rear panel outputs, the DPR channels using the Volume Control offers Harman Kardon’s exclusive configurable When the menu appears, the internal test tone front panel output jack feature. For easy connec- will be turned off. This will allow you to use your...
Operation With Stereo and VMAx modes the adjustment Memory Backup procedure described above is the only way to trim This product is equipped with a memory backup the output level, e.g. to match the Stereo or system that preserves tuner presets and system VMAx level with other modes.
Advanced Features The DPR is equipped with a number of advanced Front-Panel-Display Fade Display Brightness features that add extra flexibility to the unit’s In normal operation, the front-panel displays and The DPR’s front panel Main Information operation. While it is not necessary to use these indicators remain on at full brightness, although Display is set at a default brightness level...
Advanced Features Turn On Volume Level Semi-OSD Settings Full-OSD Time Out Adjustment menu system is used to As is the case with most audio/video receivers, The semi-OSD system places one line messages simplify the setup and adjustment of the DPR when the DPR is turned on, it will always return at the lower third of the video display screen using a series of on-screen menus.
8-Channel Direct Inputs in the is capable of sending one source to a second able through the Harman Kardon Web Site at remote zone, as long as the Dolby Pro Logic IIx zone in the house while separate source is lis- www.harmankardon.com.
DPR, you may use the main remote control Set Button , and then press the or any remote programmed with Harman Kardon To activate the feed to the remote room, press Navigation Button until the desired input codes.
Multiroom Operation 4. Stations may also be tuned directly by press- Preset Tuning ing the Direct button , and then pressing Using the remote, up to 30 stations may be the Numeric Keys that correspond to the stored in the DPR’s memory for easy recall using station’s frequency.
Tuner Operation RDS Operation Some RDS stations may not include some of • : Country Music these additional features. If the data required The DPR is equipped with RDS (Radio Data • : National Music for the selected mode is not being transmitted, System), which brings a wide range of informa- the Main Information Display will show...
(PVR) such as TiVo and Replay are pro- may be programmed into the DPR 1005 remote (Figure 21), if your device has turned off, press grammed by selecting VCR as the device. For...
Programming the Remote Although the DPR remote is preprogrammed corner of the LCD display’s top line to remind 11. When pressing the “1” button does not turn with an extensive library of codes for many major you that the remote is working even though the device being programmed back on, brands, it is also possible that you may have you may not see anything happening to the...
Programming the Remote of the LCD screen, as shown in Figure 26. 8. Continue to hold the button on the original Changing Devices Press the Set Button to begin the remote until the DPR’s display changes In the factory default settings, the DPR remote is process of learning commands from another again.
Programming the Remote In this case we will select “TV,” and show how (Figure 21), press the Set Button , and bottom line of the LCD screen, as shown in to change it to take on the codes for operating then skip to Step 9.
Programming the Remote 7. The next display (Figure 42) and the subse- appear in the remote’s LCD display. Macros 2. The remote’s message (Figure MAIN MENU quent screens are where the actual macro programmed into one of the four discrete 16), will appear in the LCD display and the programming take place.
Page 51
Programming the Remote Volume Punch-Through red. Press the Navigation Buttons P U N C H - T H R O U G H Follow these steps to enable the Volume until appears on the bot- PUNCH-THROUGH - A V R Up/Down and Mute controls from one device to tom line of the LCD screen, as shown in Figure Figure 51...
To restore the EzSet feature to normal operation, Figure 59 repeat the procedure outlined above, except that Harman Kardon’s patented EzSet feature makes 4. The next display screen (Figure 60) is where in step #3 you should press the it easier than ever to calibrate the output levels...
Programming the Remote Renaming 6. To enter the new name, press the Numeric Notes on Renaming Devices: Keys . The letters above the numbered • To move the cursor to the right or left of the While the names given to the buttons and inputs buttons indicate which letter or symbol will display during the renaming process, press the on the DPR represent recognizable categories of...
Programming the Remote lower line of the LCD. When the desired device 8. After you enter the first letter of the new Resetting the Remote name appears, press the Set Button device name, there are three options for Depending on the way in which the remote has entering the next character: been programmed, there may be a situation S E L E C T A D E V I C E...
Page 55
Programming the Remote Additional Notes on Configuring and • When the batteries approach a level below Operating the Remote: which the remote will not function, the • When the remote is being programmed, it will remote’s LCD screen will display a automatically time-out if no button is pressed warning as shown in Figure LOW BATTERY...
• Amplifier is in protection mode • Contact your local Harman Kardon service center due to internal problems No sound from surround or • Incorrect surround mode • Select a mode other than Stereo center speakers •...
Height measurement includes feet and chassis. All features and specifications are subject to change without notice. Harman Kardon and Power for the Digital Revolution are registered trademarks of Harman International Industries, Incorporated. is a trademark of Harman International Industries, Inc.