Page 1: Table Of Contents
WM6602AJ Full Automatic Washing Machine Contents Before using Names of the parts.....the 2 cover Safety precautions .......1 Introduction of the special functions..3 Installation and adjustment ....3 Install the water inlet hose....5 Using process Preparation before washing .....7 Put in the laundries ......8 Usage of the detergent .......9...
Page 2: Before Using
Ê ¹ Ó Ã Ö ® Ê ¹ Ó Ã Ö ® Ê ¹ Ó Ã Ö ® Ê ¹ Ó Ã Ö ® Before Using Before Using Names of the parts Honourable users, Thank you for choosing our products. Our products integrate high-tech, precision,frontier science.To facilitate using it, please read this manual carefully and operate this machine according to it.
Page 3: Safety Precautions
Before Using Before Using Safety precautions The power cord plug should be convenient Please plug the plug on special 220V-240V to be pluged in or pluged out with hand AC receptacle.Be sure to use single- phase while the washing machine runs normally. tow pins receptacle.Ensurethe earthing Be sure to pull the plug out and close the prong of the power receptacle is earthed...
Page 4 Before Using Before Using Do not stretch hands into the working Do not decompose, repair or alter the machine. It is dangerous even if the machine by yourself. rotation is slow. Take special care of the children.Do not let the children climb the washing machine.
Page 5: Introduction Of The Special Functions
Special functions Before Using Before Using "Hand scrub" wash: The drum and pulsator rotate in opposite directions to form a washing water flow similar to hand scrubbing movement, and meanwhile the drum inner wall also take a share in washing, which obviously increase the washing intensity.
Page 6: Usage Of The Drain Hose
Before Using Before Using How to change the direction of the drain hose 1.Lean the machine down gently with the front 3.Extend the drain hose from the left side. Push the surface facing the ground. Loosen the eight drain hose into the groove with hands. screws by a cross screwdriver.
Page 7: Install The Water Inlet Hose
Before Using Before Using Install the water inlet hose Confirm the water tap Water tap,not suitable Water tap,suitable Outlet end surface >10mm It is required that the front end shall be longer than 10mm. The outlet end surface of the tap shall be flat and smooth. If not please file it to avoid leakage.
Page 8: Connection Between The Water Inlet Hose And The Washing Machine
Before Using Before Using Connection between the water inlet hose and the washing machine 1.Do not take off the water absorption Nut of the water inlet hose cushion. Please check if the cushion is dropped or damaged before each usage. If it happens please contact our after-sale department immediately.
Page 9: Using Process
Using process Using process 1 Preparation before washing Preparation before washing 1.Connect the water inlet hose and open the water tap . 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe.
Page 10: Put In The Laundries
Using process Using process 2 Put in the laundries The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. One time washing quantity shall be lower than the rated capacity.
Page 11: Usage Of The Detergent
Using process Using process 3 Put in the detergent How to use the washing powder Direct dissolved in the machine 1.Fill water to "Low" water level. 2.Add the power. Run for 30 seconds Inlet box of the detergent to dissolve it completely. 3.Put in the laundries.
Page 12: Use The Operation Buttons
Using process Using process 4 Use the operation buttons Description of the function of the buttons Mode and meaning of the indicator light Flashing: indicate the running program On: indicate the program about to run, or indicate the selected mode "PROCEDURE"button Flashing rapidly: indicate abnormal condition STANDARD...
Page 13 To indicate remaining min. During program running. To indicate remaining reserved time (hrs) during reservation period. To indicate fault symbols for abnormal conditions (see page 16) Page 16 SURPLUS MIN WM6602AJ POWER START ON / OFF PAUSE RESERV ATION The N...
Page 14 Using process Using process Operating procedure and explanations for the buttons STANDARD SOAK JEANS WASH WM6602AJ GENTLE RINSE QUICK WASH POWER SPIN ON / OFF START WATER LEVEL PROGRAM PAUSE SELECTION SELECTION PROCEDURE RESERV SELECTION ATION 1 Press the "POWER ON/OFF" button to switch on...
Page 15: Water Level
Using process Using process Attention Even there's no water in the tub, the spinning will start after a certain period. laundries Do not use soak process for woolen Wash the laundries that are prone to lose colors separately from other laundries. The pulsator will not rotate unless the water is filled to selected water level.
Page 16: Close The Top Lid
Using process Using process Time list of each program (minute) Wash Rinse Spin Water Program Total time(min) (min) (min) (min) level Standard 1~10 Rinse twice,each about2 About 35~47 About 6 Jeans About 35~47 Rinse twice, each abut 2 1~10 About6 About 20 About 2 Gentle...
Page 17: Disposal After Washing
Using process Using process Disposal after washing After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. When washing, lint filter must be used After using, please clean it in time.
Page 18: Trouble Shooting Answer To Question
Trouble shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company.
Page 19: Packing List
Common phenomena Phenomena Explanation The spinning is intermittent when it starts. Balance the laundries to avoid slanting. Push the "Procedure selection" button to The program is setting the drain time. Some time is select "Spin", but it doesn't work. needed before it starts spinning. There may be some water flowing out of It is the water remained in the factory inspection of the drain hose in the first use of the machine.
Page 20: Specifications
Specification Specification Model WM6602AJ 220V-240V~ 50Hz Rated voltage frequency 6.0kg Rated washing / spinning capacity Water level/Water quantity (about) About 126L (High water level; Standard program) Max water consumption 0.03MPa-0.78MPa pressure 380W Rated washing power Rated spinning power 280W Weight...

Haier WM6602AJ User Manual

Quick Links

Related Manuals for Haier WM6602AJ

Summary of Contents for Haier WM6602AJ

Table of Contents