Related Manuals for Conair MAN EASYCUT CM7437SA
Summary of Contents for Conair MAN EASYCUT CM7437SA
- Page 1 THEEASYCUT TOOL TIPS for the clipping kit for easy at home hair cutting. CM7437SA...
- Page 2 HERE YOU ARE. RIGHT WHERE YOU NEED TO BE, MAN. FROM THE STREETS OF BROOKLYN, NEW YORK WE ARE CHANGE MAKERS & STYLE CREATORS. WE’VE FOUGHT OUR WAY INTO YOUR HANDS TO HELP YOU CRAFT A REPUTATION, NOT JUST ENGAGE IN SOME BRILLIANT GROOMING.
- Page 3 THE EASY CUT / TOOL TIPS CRAFT A REPUTATION, MY MAN...
-
Page 4: Important Safety Instructions
THE EASY CUT / TOOL TIPS IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, especially when children are present, basic safety instructions should always be followed, including the following: Polythene bags over product or package may be dangerous. To avoid danger of suffocation, keep this wrapper away from babies and children. - Page 5 Do not leave unattended when plugged in or switched on. Do not place on any heat sensitive surface. - Do not use any attachments other than those supplied by Conair Australia Pty Ltd. - Use this appliance only for its intended use as described within this instruction booklet.
- Page 6 THE EASY CUT / TOOL TIPS THE EASY CUT HEY MAN, IT’S CLIPPING TIME. The Easy Cut is the clipping kit for easy at home hair cutting. 1. Diamond sharpened blades 7. 6 cutting comb guides - 8. Barber comb grades #1, #2, #3, #4, #5, 2.
-
Page 7: Mains Operation
THE EASY CUT / TOOL TIPS PREPPING YOUR NEW TOOL MAINS OPERATION - Ensure your new clipper is switched off before plugging into a power outlet. - Plug your new clipper into a suitable power outlet and switch the product on by sliding the on/off switch to the ‘on’... - Page 8 THE EASY CUT / TOOL TIPS How to Adjust the Power Screw for Optimal Performance Follow these simple steps to adjust the power screw and get the best performance from your magnetic motor hair clipper: 1. Turn Off and Unplug the Clipper: Safety first! Always make sure your Fig.
-
Page 9: Before Using
THE EASY CUT / TOOL TIPS OILING THE BLADES To get the sharpest, most precise cut, it is highly recommended to oil the blades before each use. Using the oil supplied with your new clipper, unscrew the cap & cut off the very end of the plastic tube with a pair of scissors to release the oil. - Page 10 THE EASY CUT / TOOL TIPS ALIGNING THE BLADES 1. First you’ll need to remove the blades from your clipper. To remove the blades simply unscrew the two screws located on the back of the blade (see Fig.3). The two blades should then simply be removed from the clipper head. Keep the screws aside for reapplying the blades to the clipper head.
- Page 11 THE EASY CUT / TOOL TIPS Philips head screwdriver until secure. 5. The clipper is now suitable for use. EASY CLIPPING, YOUR WAY The Easy Cut features 6 cutting comb guides - grades #1, #2, #3, #4, #5, and #6 comb guides (3mm to 19mm) for cutting, shaping &...
- Page 12 THE EASY CUT / TOOL TIPS CLIPPING TIPS CHECK OUT CONAIRMAN.COM.AU FOR GROOMING TIPS & KNOW HOW TO LET YOU CRAFT A REPUTATION CREATING AN ALL-OVER EVEN CUT 1. Ensure the clipper is switched off. 2. Attach the desired cutting comb guide as required. 3.
- Page 13 THE EASY CUT / TOOL TIPS CREATING A SHORT BACK & SIDES LOOK, WITH LENGTH ON THE TOP 1. Ensure the clipper is switched off. 2. Attach the desired cutting comb guide as required. 3. Switch the clipper on – the blades will start to move. 4.
- Page 14 Always use the cleaning brush to clean the clipper head. NOTE: Do not attempt to repair or replace the blades. In the event that the blades become blunt or damaged, contact the Conair CustomerCare Line (Conair Customer Service).
- Page 15 1. In this warranty document (“Warranty Document”), “Conair”, “we” or “us” means: • Conair Australia Pty Limited (ABN 64 068 492 044) of The Equinox Centre, Suite 101, 18 Rodborough Rd, Frenchs Forest, NSW, 2086, in relation to products purchased in Australia; or Conair New Zealand Ltd of Conair New Zealand Limited, PO BOX 251159 Pakuranga, Auckland 2140, New Zealand in relation to products purchased in New Zealand.
- Page 16 11. Within the Standard Warranty Period, if your product suffers a defect in the materials or workmanship, Conair will either refund or replace your product, in our sole discretion, for no charge. 12. Under this Standard Warranty, we do not have to refund, repair or replace your product if the product’s defect or damage is a result of misuse, abuse, accident, act of God such as...
- Page 17 Conair distributor or reseller. For clarity, all warranties are only enforceable in Australia and New Zealand. 20. To the fullest extent permitted by law, Conair does not accept liability for: a) any loss or damage however suffered, caused by or arising out of any failure to use a product in accordance with Conair’s instruction booklet;...
- Page 18 25. Replacement parts may be available for your product. Contact us on the phone or email address provided for more details. Please provide your product name/model number details, date of purchase and part you require. CONTACT INFORMATION Conair Australia Pty Ltd PO Box 146 Terrey Hills NSW 2084 Customer Service Australia 1800 650 263 email: aus_info@conair.com...
- Page 19 ©2024 Conair Australia Pty. Ltd. Suite 101, 18 Rodborough Rd Frenchs Forest NSW 2086 Australia Conair New Zealand Limited PO BOX 251159 Pakuranga, Auckland 2140 New Zealand CONTACT US For advice & tips on your new ConairMan product email us on: aus_info@conair.com...
- Page 20 THE EASY CUT / TOOL TIPS CRAFT A REPUTATION, MY MAN IB-24/248...
Need help?
Do you have a question about the MAN EASYCUT CM7437SA and is the answer not in the manual?
Questions and answers