Advertisement
Advertisement
Table of Contents
Related Manuals for Donaldson BOFA PrintPRO Oracle DS
Summary of Contents for Donaldson BOFA PrintPRO Oracle DS
- Page 1 PrintPRO Oracle DS USER MANUAL...
- Page 2 Contents Overview of your extraction system (front) Overview of your extraction system (back) Overview of the control panel Important safety notes Safety labels Unpacking the and unit placement Connecting to power supply Turning extractor on / Adjusting airflow Cleaning the unit Filter replacement Consumables spares &...
- Page 3 Overview Control Panel Power switch HEPA Filter Pre Filter Filter clamp handle Lockable Castors Door Catches...
- Page 4 Overview Interface cable entry Motor cooling intake cowl Mains power cable entry Exhaust Outlet Air Inlet ports...
- Page 5 Overview...
-
Page 6: Safety Instructions
Important Safety Instructions To reduce the risk of fire, electric shock or injury: Always isolate the system from the mains power supply before removing the pump/motor access panel. 2. Use only as described in this manual. Connect the system to a properly grounded outlet. Important safety notes Concerning symbols used on the extraction unit and referred Dangers to eyes, breathing and skin... - Page 7 Serial Number Label Safety Instructions Warning and Information labels The following list details labels used on your PrintPro Oracle DS unit. Location: Next to mains inlet. Meaning: This label contains a variety of information about Goggles, Gloves & Mask Label the extraction unit, including.
- Page 8 Safety Instructions Packaging Removal & Unit Placement Before installation, check the extraction unit for damage. All packaging must be removed before the unit is connected to the power supply. Please read all instructions in this manual before using this extractor. 1.
-
Page 9: Installation
Installation Connection to Power Supply Please follow the specification at the rear of this manual when selecting the power supply outlet for the PrintPro Oracle DS system, ensure the power supply is suitable before connecting the system. Check the Integrity of the electrical power cable, if the supply cord is damaged the extraction unit should not be connected to the mains. -
Page 10: Operation
Operation Increase Airflow Turning extraction unit On Press the main switch to the “On” position (Refer to section 1 for switch location) by depressing the ‘I’ side of the switch. Decrease Airflow Setting the desired airflow Flashing LEDs The PrintPro Oracle DS features autoflow controls. This enables the user to set the required airflow rate. -
Page 11: Maintenance
no longer removes fume efficiently. Maintenance It is recommended that a spare set of filters are kept on site to avoid prolonged unit unavailability. Part numbers for replacement filters can be found on the filters fitted in your system. To prevent overheating, units should not be run with a Maintenance UK blocked filter condition, or with dust obstruction of Inlets / Outlets. - Page 12 Filter removal Maintenance To remove and replace the Pre filter follow the procedure detailed below. Isolate the electrical supply to the extractor Undo the catches on the front of the unit and open the door. The filter assembly is removed by rotating the lever Filter Replacement below the filter through 180 to lower the filter...
- Page 13 Replacing the Carbon Filter element Where fitted, the carbon filter element is the uppermost section of the filter assembly Replacing the Hydrophobic HEPA Filter element (no The carbon filter element should be lifted from the carbon filter fitted) assembly. To remove and replace the Hydrophobic HEPA filter follow Replacing the Hydrophobic HEPA Filter element the procedure detailed below.
-
Page 14: Replacement Parts
Filter disposal Replacement Parts The DS Range of filters are manufactured from non-toxic materials. Filters are not re-usable, cleaning used filters is not recommended. The method of disposal of the used filters depends on the material deposited on them. For your guidance Consumable Spares Deposit Comment... -
Page 15: System Specifications
System Specifications Unit: PrintPro Oracle DS Capacity: 380m /h 223cfm Weight: 54.5Kg (120lbs) Motor: Centrifugal Fan Output: 1100w Electrical supply: 115-230V Hertz: 50/60Hz Full Load Current: 12.5A Noise Level: Below 60dB (A) (at typical operating speed) Size: Metric (mm) Imperial (inches) Height 32.2... -
Page 16: Contact Information
Contact Information BOFA Headquarters 19-20 Balena Close Creekmoor industrial Estate Poole Dorset BH17 7DU Phone: +44 (0) 1202 699 444 BOFA Americas 303 S.Madison Street Staunton Illnois 62088 Phone: +1 (618) 205 5007 BOFA International GmbH Sudring 62 D-21465 Wentorf bei Hamburg Germany Phone: +49 (0) 40 7393735-15...
Need help?
Do you have a question about the BOFA PrintPRO Oracle DS and is the answer not in the manual?
Questions and answers