Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Junker JS65X00EAE
Summary of Contents for Junker JS65X00EAE
- Page 1 Dishwasher JS65X00EAE Information for Use...
-
Page 2: Table Of Contents
Table of contents 1 Safety ........... 4 8.6 Cutlery basket ...... 23 1.1 General information.... 4 8.7 Basket heights...... 23 1.2 Intended use...... 4 9 Before using for the first time .. 24 1.3 Restriction on user group.. 4 9.1 Performing the initial config- 1.4 Safe installation ...... - Page 3 14.7 Terminate programme... 34 14.8 Switching off appliance .. 34 15 Basic settings...... 35 15.1 Overview of the basic set- tings........ 35 15.2 Changing basic settings.. 37 16 Cleaning and servicing ... 38 16.1 Cleaning the tub .... 38 16.2 Cleaning products .... 38 16.3 Tips on appliance care..
-
Page 4: Safety
en Safety 1 Safety Observe the following safety instructions. 1.1 General information Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe ¡ for future reference or for the next owner. Do not connect the appliance if it has been damaged in transit. ¡... - Page 5 Safety en WARNING ‒ Risk of electric shock! Incorrect installation is dangerous. Connect and operate the appliance only in accordance with the ▶ specifications on the rating plate. Always use the supplied power cable for the new appliance. ▶ Connect the appliance to a power supply with alternating cur- ▶...
-
Page 6: Safe Use
en Safety Contact between the appliance and installation lines may lead to a defect in these lines, e.g. gas pipes and power lines. Gas from a corroded gas pipe can ignite. A damaged power line can cause a short circuit. Check that there is a distance of at least 5 cm between the ap- ▶... - Page 7 Safety en Highly caustic alkaline or highly acidic cleaning agents in conjunc- tion with aluminium parts in the interior of the appliance may cause explosions. Never use highly caustic alkaline or highly acidic cleaning ▶ agents, in particular commercial or industrial products, in con- junction with aluminium parts (e.g.
-
Page 8: Damaged Appliance
en Safety 1.6 Damaged appliance WARNING ‒ Risk of electric shock! If the appliance or the power cord is damaged, this is dangerous. Never operate a damaged appliance. ▶ Never operate an appliance with a cracked or fractured surface. ▶ Never pull on the power cord to unplug the appliance. Always ▶... - Page 9 Safety en WARNING ‒ Risk of harm to health! Children can lock themselves in the appliance, thereby putting their lives at risk. With redundant appliances, unplug the power cord. Then cut ▶ through the cord and damage the lock on the appliance door beyond repair so that the appliance door will no longer close.
-
Page 10: Preventing Material Damage
en Preventing material damage Modified or damaged water hoses Preventing material damage 2 Preventing material may result in material damage and damage to the appliance. damage Never kink, crush, modify or cut ▶ through water hoses. Preventing material damage 2.1 Safe installation Only use the water hoses supplied ▶... -
Page 11: Environmental Protection And Saving Energy
Environmental protection and saving energy en So as not to scratch the finish on 3.3 AquaSensor ▶ the appliance, do not use sponges The AquaSensor is an optical meas- with a rough surface or abrasive uring device (light barrier) which cleaning agents. measures the turbidity of the washing To prevent corrosion, do not use ▶... -
Page 12: Installation And Connection
en Installation and connection installing it under a continuous work- Installation and connection 4 Installation and con- top that is securely connected to ad- jacent cabinets. nection Follow the safety instructions. To ensure proper operation, connect → Page 4 Installation and connection the appliance to the power and water Follow the instructions for electrical supply correctly. -
Page 13: Drinking Water Connection
Installation and connection en 4.4 Drinking water connec- tion Connect your appliance to a drinking water connection. Installing the drinking water connection Note If you are replacing the appliance, ¡ you must use a new water supply hose. Consult the installation instructions supplied for the steps required here. -
Page 14: Familiarising Yourself With Your Appliance
en Familiarising yourself with your appliance Familiarising yourself with your appliance 5 Familiarising yourself with your appliance Familiarising yourself with your appliance 5.1 Appliance You can find an overview of the parts of your appliance here. Rating plate Rating plate with E number and FD num- ber → Page 59. - Page 15 Familiarising yourself with your appliance en Detergent dispenser Add detergent to the detergent dispenser. → "Detergent", Page 28 Bottom basket Bottom basket → Page 22 Dispenser for special salt Add special salt to the dispenser for spe- cial salt. → "Water softening system", Page 24 Lower spray arm The lower spray arm washes the table- ware in the bottom basket.
-
Page 16: Controls
en Familiarising yourself with your appliance 5.2 Controls You can use the control panel to configure all functions of your appliance and to obtain information about the operating status. With some buttons you can perform different functions. ON/OFF button and reset Switching on the appliance button → Page 33 Switching off the appliance... -
Page 17: Programmes
Familiarising yourself with your appliance en button If you press for approx. 3 seconds, you can open the basic set- tings. → "Changing basic settings", Page 37 Start button Starting the programme → Page 34 Programme buttons and addi- Programmes tional functions → "Programmes", Page 18 Additional functions → "Additional functions", Page 20 Timer programming Setting timer programming... - Page 18 en Programmes Programmes 6 Programmes You can find an overview of the pro- ted. The running time will change if Programmes grammes that can be selected here. the rinse aid system is switched off Different programmes, which can be or rinse aid needs to be added. found on the control panel of your The consumption values can be appliance, are available depending...
-
Page 19: Information For Test Institutes
Programmes en Programme Programme se- quence Tableware: Time-optimised: Mixed tableware and cutlery Cleaning 65 °C ¡ ¡ 1 hr Programme Level of soiling: Intermediate rinse ¡ Common household food rem- Final rinse 69 °C ¡ ¡ nants lightly dried on ¡ Tableware: Cold rinsing: All types of dishes Pre-Rinse ¡... -
Page 20: Additional Functions
en Additional functions Additional functions 7 Additional functions You can find an overview of the additional functions that can be selected here. Additional functions Different additional functions, which can be found on the control panel of your appliance, are available depending on the appliance configuration. You can se- lect certain additional functions depending on the programme. -
Page 21: Features
Features en Press in the levers on the right and Features 8 Features left on the outside of the basket. You can find an overview of the pos- Features sible features of your appliance and how to use them here. These features depend on the model of your appliance. -
Page 22: Knife Shelf
en Features 8.2 Knife shelf 8.4 Bottom basket Use the shelf for knives and long Arrange pans and plates in the bot- items of cutlery. tom basket. Cutlery basket 8.3 Etagere Large plates up to a diameter of 31 cm can be arranged in the bottom Use the cutlery shelf and space un- basket as shown. -
Page 23: Folding Prongs
Features en Push the lever forwards and fold 8.5 Folding prongs down the prongs . Use the folding prongs to position tableware securely, e.g. plates. To use the prongs again, fold them back up. The prongs audibly click into posi- You can fold the prongs down to po- tion. -
Page 24: Before Using For The First Time
en Before using for the first time Level Top basket Bottom basket 3 max. ø 27 cm 25 cm Start the Programme with the Before using for the first time 9 Before using for the highest cleaning temperature without tableware. first time To remove any marks from water Before using for the first time or other residues, we recommend... -
Page 25: Setting The Water Softening System
Water softening system en Water hardness Hardness range mmol/l Setting value °E 21 - 26 Hard 3.0 - 3.7 27 - 38 Hard 3.8 - 5.4 39 - 62 Hard 5.5 - 8.9 Note: Set the water hardness determ- gramme starts. The consumption of ined on your appliance. -
Page 26: Switching Off The Water Softening System
en Water softening system Note: Only use special salt for The water hardness is 0 - 8 °E. ¡ dishwashers. You do not need to use special Do not use salt tablets. salt. Do not use table salt. Press . Add the special salt to the dis- To open the basic settings, press penser. -
Page 27: Rinse Aid System
Rinse aid system en Add rinse aid up to the max mark. Additional power consump- 0.05 tion in kWh The consumption values specified are laboratory measurements determ- ined in accordance with the currently applicable standard using the Eco 50° programme and with the factory value of the water hardness set to 16 - 20 °E. -
Page 28: Switching The Rinse Aid System Off
en Detergent To save the settings, press starch and remove protein. Oxygen- for 3 seconds. based bleaching agents are generally used to remove coloured marks, e.g. tea or ketchup. 11.3 Switching the rinse aid system off Note: Follow the manufacturer's in- structions for each detergent. If you find the rinse aid refill indicator Tip: Suitable detergents are available irritating, e.g. -
Page 29: Unsuitable Detergents
Detergent en With powder and liquid detergent the 12.3 Information on deter- dosage can be individually adjusted gents to the level of soiling of the table- ware. Follow the instructions on detergents For better washing and drying results in everyday use. and to avoid damage to the appli- Detergents marked as "organic"... - Page 30 en Tableware Add the detergent to the dry deter- Close the lid of the detergent dis- gent dispenser. penser. 50 ml 25 ml 15 ml If you are using tablets, one is The lid clicks into position. enough. Insert the tablets in a hori- The detergent dispenser will open zontal position.
-
Page 31: Tableware
Tableware en 13.1 Damage to glass and Cause Recommenda- tion tableware Highly caustic al- If you are using Only put glasses and china in the kaline or highly highly caustic al- dishwasher if it is marked as dish- acidic cleaning kaline or highly washer-safe by the manufacturer. - Page 32 en Tableware allowing steam to escape and water To save resources, do not pre- to leak out around the door. This rinse tableware under running wa- could damage your kitchen units. ter. Observe the following when arran- ging tableware: – Put heavily soiled tableware in the bottom basket, e.g.
-
Page 33: Removing Tableware
Basic operation en 13.3 Removing tableware 14.2 Setting a programme To adjust the washing programme to WARNING the soiling level of the tableware, se- Risk of injury! lect a suitable programme. Hot tableware can cause burns to the skin. When hot, tableware is sensitive Press the right programme button. -
Page 34: Starting The Programme
en Basic operation 14.5 Starting the programme 14.7 Terminate programme Press . To end a programme early or to ▶ switch from a programme that has The programme has ended when already started, you will need to can- the display shows "0h:00m". cel it first. Notes Open the appliance door. -
Page 35: Basic Settings
Basic settings en Basic settings 15 Basic settings You can configure the basic settings for your appliance to meet your needs. Basic settings 15.1 Overview of the basic settings The basic settings depend on the features of your appliance. Basic setting Display text Selection Description Water hardness H00 - H07... - Page 36 en Basic settings Basic setting Display text Selection Description InfoLight I00 - I01 Switch InfoLight on or off. While the programme is run- ning, a spot of light is pro- jected onto the floor below the appliance door. This light will not be visible if the appli- ance is installed at eye level with the cabinet front fitted flush.
-
Page 37: Changing Basic Settings
Basic settings en Basic setting Display text Selection Description Automatic door o00 - o02 Activate or deactivate auto- opening matic opening of the appli- ance door during the drying phase. If the function has been ac- tivated, the running time may increase. -
Page 38: Cleaning And Servicing
en Cleaning and servicing 16.2 Cleaning products Cleaning and servicing 16 Cleaning and servi- Only use suitable cleaning products cing to clean your appliance. → "Safe use", Page 10 To keep your appliance working effi- Cleaning and servicing ciently for a long time, it is important 16.3 Tips on appliance care to clean and maintain it carefully. -
Page 39: Filter System
Cleaning and servicing en To ensure optimum cleaning perform- Pour the machine cleaner into the ance, the programme doses the de- detergent dispenser until it is filled tergents independently of each an- completely. other during the relevant cleaning Do not place any additional ma- phase. -
Page 40: Cleaning Spray Arms
en Cleaning and servicing Turn the coarse filter anticlockwise Carefully clean the rim of dirt and remove the filter system . between the coarse and the fine fil- ter. Check that no foreign objects ‒ Re-assemble the filter system. fall into the sump. Make sure that the locking catches on the coarse filter click into posi- tion. - Page 41 Cleaning and servicing en Pull up the lower spray arm to re- move. Check the outlet nozzles on the spray arms for blockages under running water and remove any for- eign bodies. Insert the lower spray arm. The spray arm clicks into position. Insert the upper spray arm and screw it firmly in place.
-
Page 42: Troubleshooting
en Troubleshooting Troubleshooting 17 Troubleshooting You can rectify minor faults on your appliance yourself. Read the troubleshoot- Troubleshooting ing information before contacting after-sales service. This will avoid unneces- sary costs. WARNING Risk of electric shock! Incorrect repairs are dangerous. Repairs to the appliance should only be carried out by trained specialist ▶... - Page 43 Troubleshooting en Fault Cause and troubleshooting Appliance door opens Use size 4X30 bolts to adjust the door gap. ▶ too wide at the end of The bolts are included in the scope of supply. the programme. If you use bolts that are too long, this can deactiv- ate the function of automatic door opening.
- Page 44 en Troubleshooting Fault Cause and troubleshooting E:32-00 will light up Pull out the mains plug. alternately or indicator Turn off the water tap. for water supply lights Unscrew the water connection. Remove the filter from the inlet hose Clean the filter. Re-insert the filter in the inlet hose.
- Page 45 Troubleshooting en Fault Cause and troubleshooting E:61-03 will light up Not an appliance fault. Siphon connection is still alternately. Water is closed or the wastewater hose is kinked or blocked. not drained. Check the connection to the siphon and open if ne- cessary.
- Page 46 en Troubleshooting Fault Cause and troubleshooting A different error code A technical fault is present. appears in the display Press window. Unplug the appliance or switch off the fuse. Wait at least 2 minutes. E:01-00 to E:90-10 Insert the mains plug of the appliance in a socket or switch on the fuse.
- Page 47 Troubleshooting en Fault Cause and troubleshooting Tableware is not dry. Activate Extra Dry. ▶ Tableware removed too early or drying process not yet ended. Wait until the programme ends. Only remove tableware 30 minutes after the pro- gramme has ended. Rinse aid used has a limited drying performance. Use a name-brand rinse aid.
-
Page 48: Cleaning Spray Arms", Page
en Troubleshooting Fault Cause and troubleshooting Remnants of food on Arrange tableware so that it does not obstruct ▶ tableware. spray arm rotation. Spray arm nozzles are blocked. Clean the Spray arms → Page 40. ▶ Filters are soiled. Clean the filters. ▶ → "Cleaning filters", Page 39 Filters are inserted incorrectly and/or not engaged. - Page 49 Troubleshooting en Fault Cause and troubleshooting Detergent residue in Lid of the detergent dispenser is blocked by items of the appliance tableware parts and will not open. Arrange tableware in the top basket tableware so the tab collecting tray is not obstructed by table- ware.
- Page 50 en Troubleshooting Fault Cause and troubleshooting Wipeable or water-sol- Special salt dispenser is not screwed tight. uble coatings are Screw the special salt dispenser tight. ▶ present inside the ap- pliance or on the door. Stubborn white coat- Detergent substances are deposited there. These ings are present on coatings cannot generally be removed with chemicals.
- Page 51 Troubleshooting en Fault Cause and troubleshooting Coloured coatings The formation of films is due to substances contained (blue, yellow, brown) in vegetables (cabbage, celery, potatoes, noodles, that are difficult or im- etc.) or tap water (manganese). possible to remove Clean the appliance. ▶...
- Page 52 en Troubleshooting Fault Cause and troubleshooting Removable streaks Amount of rinse aid to be dispensed is set too high. are present on Set the rinse aid system to a lower setting. ▶ glasses, glassware → "Setting the amount of rinse aid", Page 27 with a metallic appear- No rinse aid has been added.
- Page 53 Troubleshooting en Fault Cause and troubleshooting Rust spots on cutlery. Remove any spilled special salt from the tub. Screw the cap of the special salt dispenser on tight. Detergent residue is Spray arms were blocked by tableware so detergent present in the deter- was not rinsed out.
- Page 54 en Troubleshooting Fault Cause and troubleshooting Water is left in the ap- Filter system or area under the filters is blocked. pliance at the end of Clean the Filters → Page 39. the programme. Clean the Wastewater pump → Page 57. Programme has not yet ended. Wait until the programme ends or cancel the pro- ▶...
- Page 55 Troubleshooting en Fault Cause and troubleshooting All LEDs lit up or A software update is possibly installing. flashing. Wait until the software update has been installed. This process can take approx. 30 minutes. If the appliance is not ready to use after 30 minutes, perform a reset.
- Page 56 en Troubleshooting Fault Cause and troubleshooting Knocking or rattling With a small load the water jets directly strike against noise. the tub. Distribute the tableware evenly. ▶ Load the appliance with more tableware. ▶ Light items of tableware move about during the wash cycle.
-
Page 57: Clean Wastewater Pump
Transportation, storage and disposal en Insert the pump cover and press 17.1 Clean wastewater pump down . Large remnants of food or foreign bodies can block the waste water pump. As soon as the rinsing water no longer drains properly, the waste water pump must be cleaned. -
Page 58: Protect Appliance From Frost
en Customer Service 18.2 Protect appliance from 18.4 Disposing of old appli- frost ance If there is a risk of frost where the ap- Valuable raw materials can be re- pliance will be standing, e.g. in a holi- used by recycling. day home, empty the appliance com- pletely. -
Page 59: Product Number (E-Nr.), Production Number (Fd) And Consecutive Numbering (Z-Nr.)
Customer Service en Customer Service for a period of at least 10 years from the date on which your appliance was placed on the market within the European Eco- nomic Area. Note: Under the terms of the manu- facturer's warranty the use of Cus- tomer Service is free of charge. -
Page 60: Technical Specifications
en Technical specifications Technical specifications 20 Technical specifications Technical specifications Weight Max.: 60 kg Voltage 220 - 240 V, 50 Hz or 60 Hz Power rating 2000 - 2400 W Fuse 10 - 16 A Water pressure min. 50 kPa (0.5 bar) ¡ max. 1000 kPa (10 bar) ¡ Inlet rate Min. 10 l/min Water temperature Cold water. -
Page 61: Declaration Of Conformity
A detailed Declaration of Conformity BSH Hausgeräte GmbH hereby de- Declaration of Conformity can be found online at www.junker- clares that the appliance conforms to home.com/uk among the additional the essential requirements and other documents on the product page for relevant provisions of Directive your appliance. - Page 64 Valid within Great Britain: Imported to Great Britain by Nobilia GB Ltd. Kingsway Business Park OL16 4UG Rochdale Great Britain BSH Hausgeräte GmbH 650 V5 Carl-Wery-Straße 34 81739 München, GERMANY *9001878043* 9001878043 040313...
Need help?
Do you have a question about the JS65X00EAE and is the answer not in the manual?
Questions and answers