INSTANT HOT/COLD WATER DISPENSER CONTROL PANEL DESCRIPTION °C WARM AMBIENT TDS OUT TDS IN COOLING LOCK TEMP COLD DISPENSE WATER FILTER LIFESPAN INDICATOR DECREASE WATER TEMP OR VOL TEMP/VOL INDICATOR COOLING FUNCTION HOT WATER SELECTION VOLUME SELECTION INTERNAL COLD TANK WATER SHORTAGE INDICATOR CHILDLOCK PITCHER WATER SHORTAGE INDICATOR TEMP SELECTION...
• novita Instant Hot Water Dispenser W16 is meant for use in municipally treated water but NOT water that is microbiologically unsafe and unknown. • Individuals requiring water of a certain microbiological standard should consult the advice of their doctors or practitioners in regard to the usage of W16.
INSTANT HOT/COLD WATER DISPENSER SETTING UP Place the unit on a stable and level surface with proximity to a power supply for setting up. • There should be 20 cm clearance between the wall and by the sides of the unit for proper ventilation. •...
INSTANT HOT/COLD WATER DISPENSER Connect the power plug to the power supply and power on. Unit produce a “beep” sound and the LED display sceeen illuminates. The unit setting up is completed! NOTE ! When E8 error code appears together with blinking , it indicates that the Filter Refer Step 2 - 6 connector is not properly plugged in.
INSTANT HOT/COLD WATER DISPENSER PREPARING THE UNIT FOR TRANSPORTATION Turn off the power supply and disconnect the power plug. Lift up the source tank cover. Remove the source tank and empty the water. Lift up the purified pitcher and empty the water. Press un-lock, follwed by Press and hold the dispensing button for 5 seconds to activate internal flushing.
INSTANT HOT/COLD WATER DISPENSER USING THE INSTANT HOT/COLD RO WATER DISPENSER 1. CHILDLOCK (APPLICABLE FOR WARM AND HOT WATER) Childlock is activated by default as a safety feature and its corresponding indicator illuminates. Touch the childlock button to deactivate before selecting warm or hot water. •...
Page 10
INSTANT HOT/COLD WATER DISPENSER 8. INCREASE TEMPERATURE OR VOLUME Touch the increase button to increase the temperature or volume by 1 level. Selected temperature or volume will be indicated on the display screen. 9. DECREASE TEMPERATURE OR VOLUME Touch the decrease button to decrease the temperature or volume by 1 level.
Page 11
Please standby a new set of Filter. Please replace with a new set of HydroRO / HydroRO Filter. Scan QR Code to purchase the replacement filter from novita eStore. REMOVING EXHAUSTED FILTERS Remove source water tank cover first. Push and silde the filter cover upwards to detach it from connecting catch then lift it up.
Page 12
INSTANT HOT/COLD WATER DISPENSER INSTALLING NEW FILTERS INSTANT HOT/COLD RO WATER DISPENSER 4-STAGE HYDRO-RO+™ FILTRATION SYSTEM 12 MONTHS FILTER REPLACEMENT PACK W16F THIS PACK INCLUDES: ∙ 1x Pre-Carbon Filter ∙ 1x Hydro-RO+™ Filtration System Remove the new filter plastic wrap remove the filter cap cover. Recommended Filter Replacement: 3,600 Litres* / 12 Months (For Optimun Performance) *Based on average 10 litres a day usage...
INSTANT HOT/COLD WATER DISPENSER 3 sec 10 min Discard Wait for reverse When full osmosis indicator to stop illuminating 1. The water is now ready for consumption! After completing the pre-rinse, unit will start water Discard 3 tanks of purified water to complete the filter commissioning procedures.
Page 14
INSTANT HOT/COLD WATER DISPENSER 2. PITCHER Remove the pitcher and empty the content. Prepare a solution mixture of 50% white vinegar and 50% clean tap water and soak it inside the pitcher for 15 minutes to remove any possible minerals scaling or deposits. Rinse Drain and discard the soaked solution mixture.
Servicing should only be conducted Always use room temperature or tap DO NOT use mirco-biologically by professional service technicians water for filtration. unsafe water. from novita. 45º 20cm 20cm DO NOT tilt the unit more than Allow adequate clearance and space DO NOT move or incline the unit forty-five (45º) degrees during...
Page 16
INSTANT HOT/COLD WATER DISPENSER SAFETY PRECAUTIONS Stable & Level Surface Keep the unit away from direct DO NOT place any heavy objects on Always place the unit on a stable and sunlight or any heat source. top of the unit. level surface.
Always remember to MAINTAIN and REPLACE the filter according to its stipulated maintenance or exhaustion date. Ensure that the filter and all parts of novita Instant Hot/Cold RO Water Dispenser W16 are not cracked or damaged at all times. When damaged, the water purification process is compromised and the water might hence be unfit for consumption.
• Ensure that power plug is connected snugly. connection is loose. • Power plug or cord is damaged. • Turn OFF power and bring unit to novita Customer Care Centre for diagnosis. • Power cut-off. • Check power source & contact a qualified...
INSTANT HOT/COLD WATER DISPENSER TECHNICAL SPECIFICATIONS Product Name: Instant Hot / Cold RO Water Dispenser Model Name: Heater Power Consumption: 2160 Watts Cooling Power Consumption: 65 Watts Rated Voltage/Frequency: 220 - 240 V / 50 Hz Net Weight: 10 Kg Dimension (W x D x H): 414 mm x 233 mm x 425 mm Source Water Tank Capacity:...
MINIMUM DOWNTIME Understanding that time is of the essence, for each servicing or repair, novita guarantees that we will only take up to 7 working days to get your product up and ready for collection. OPTIONAL HOME DELIVERY Time and convenience might not always be in the advantage of customers, hence, for a nominal fee of $12 one-way and $24 two-ways, customer can choose to use our delivery service instead of bringing in the product themselves.
This limited warranty is void if the serial number on the Product had been removed, erased, defaced, altered, tampered or is illegible. novita will repair or replace this product at their option and at no charge with new or reconditioned parts or Product if found to be defective during the limited warranty period specified above.
Need help?
Do you have a question about the W16 and is the answer not in the manual?
Questions and answers