Advertisement
Quick Links
NI NI 9997
C Series Bus Bar Module
A l l t r a d e m a r k s , b r a n d n a m e s , a n d b r a n d s a p p e a r i n g h e r e i n a r e t h e p r o p e r t y o f t h e i r r e s p e c t i v e o w n e r s .
• C r i t i c a l a n d e x p e d i t e d s e r v i c e s
• I n s t o c k / R e a d y - t o - s h i p
Artisan Scientific Corporation dba Artisan Technology Group is not an affiliate, representative, or authorized distributor for any manufacturer listed herein.
Limited Availability
New From Surplus Stock
Buy Today!
https://www.artisantg.com/49426-1
• We b u y y o u r e x c e s s , u n d e r u t i l i z e d , a n d i d l e e q u i p me n t
• F u l l - s e r v i c e , i n d e p e n d e n t r e p a i r c e n t e r
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for National Instruments 9997
Summary of Contents for National Instruments 9997
- Page 1 NI NI 9997 C Series Bus Bar Module Limited Availability New From Surplus Stock Buy Today! https://www.artisantg.com/49426-1 A l l t r a d e m a r k s , b r a n d n a m e s , a n d b r a n d s a p p e a r i n g h e r e i n a r e t h e p r o p e r t y o f t h e i r r e s p e c t i v e o w n e r s .
- Page 2 GETTING STARTED GUIDE NI 9997 2-Channel, 11 A, C Series Busbar Module...
-
Page 3: Safety Guidelines
This document explains how to connect to the NI 9997. Before you begin, complete the software and Note hardware installation procedures in your chassis documentation. The guidelines in this document are specific to Note the NI 9997. The other components in the system might not meet the same safety ratings. -
Page 4: Safety Guidelines For Hazardous Voltages
LIVE (>42.4 Vpk/60 VDC), you must ensure that devices and circuits connected to the module are properly insulated from human contact. You must use the 6-position connector backshell kit (783804-01) NI 9997 Getting Started Guide | © National Instruments | 3... -
Page 5: Safety Guidelines For Hazardous Locations
Safety Guidelines for Hazardous Locations The NI 9997 is suitable for use in Class I, Division 2, Groups A, B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4 and Ex nA IIC T4 hazardous locations; and nonhazardous locations only. - Page 6 Zone 2 hazardous locations, in ambient temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI 9997 in Gas Group IIC hazardous locations, you must use the device in an NI chassis that has been evaluated as Ex nC IIC T4, Ex IIC T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.
-
Page 7: Electromagnetic Compatibility Guidelines
Furthermore, any changes or modifications to the product not expressly approved by National Instruments could void your authority to operate it under your local regulatory rules. 6 | ni.com | NI 9997 Getting Started Guide... -
Page 8: Special Conditions For Marine Applications
In addition, take precautions when designing, selecting, and installing measurement probes and cables to ensure that the desired EMC performance is attained. NI 9997 Getting Started Guide | © National Instruments | 7... -
Page 9: Preparing The Environment
Preparing the Environment Ensure that the environment in which you are using the NI 9997 meets the following specifications. Operating temperature -40 °C to 70 °C (IEC 60068-2-1, IEC 60068-2-2) Operating humidity 10% RH to 90% RH, (IEC 60068-2-78) noncondensing... - Page 10 NI 9997 Pinout Channel 0 Channel 1 NI 9997 Getting Started Guide | © National Instruments | 9...
-
Page 11: High-Vibration Application Connections
Use the 6-position connector backshell kit (783804-01). Busbar Configurations The following sections illustrate typical busbar configurations. Connecting Multiple Shields/Common Pins to Ground The NI 9997 simplifies wiring multiple shields to ground. 10 | ni.com | NI 9997 Getting Started Guide... - Page 12 Attach the ground of the separate C Series module to a terminal on a channel of the NI 9997. • Connect the shields to the remaining terminals on the channel. NI 9997 Getting Started Guide | © National Instruments | 11...
- Page 13 Connecting Multiple Modules to Device Common Device Device C Series Modules Channel 0 Isolation NI 9997 12 | ni.com | NI 9997 Getting Started Guide...
- Page 14 Connecting Multiple Devices to One External Power Supply Device 1 Device 2 Channel 0 Device 3 Device 4 Device 5 Isolation External Power Supply – Channel 1 NI 9997 NI 9997 Getting Started Guide | © National Instruments | 13...
- Page 15 NI 9997 Specifications The following specifications are typical for the range -40 °C to 70 °C unless otherwise noted. Do not operate the NI 9997 in a manner not Caution specified in this document. Product misuse can result in a hazard. You can compromise the safety protection built into the product if the product is damaged in any way.
-
Page 16: Physical Characteristics
0.22 N · m to 0.25 N · m terminals (1.95 lb · in. to 2.21 lb · in.) Wires per screw One wire per screw terminal; terminal two wires per screw terminal using a 2-wire ferrule NI 9997 Getting Started Guide | © National Instruments | 15... - Page 17 0.2 N · m (1.80 lb · in.) flanges Ferrules Single wire 0.25 mm to 1.50 mm (24 AWG to 16 AWG) Double wire 0.823 mm (18 AWG) maximum Weight 137 g (4.8 oz) 16 | ni.com | NI 9997 Getting Started Guide...
-
Page 18: Safety Voltages
Category II Withstand 3,000 Vrms, verified by a 5 s dielectric withstand test Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. NI 9997 Getting Started Guide | © National Instruments | 17... -
Page 19: Hazardous Locations
This category refers to local-level electrical distribution, such as that provided by a standard wall outlet, for example, 115 V for U.S. or 230 V for Europe. Do not connect the NI 9997 to signals or use Caution for measurements within Measurement Categories III or IV. -
Page 20: Safety And Hazardous Locations Standards
UL 60079-0; Ed 5, UL 60079-15; Ed 3 • CSA 60079-0:2011, CSA 60079-15:2012 For UL and other safety certifications, refer to Note the product label or the Online Product Certification section. NI 9997 Getting Started Guide | © National Instruments | 19... -
Page 21: Online Product Certification
To obtain product certifications and the DoC for this product, visit ni.com/ certification, search by model number or product line, and click the appropriate link in the Certification column. 20 | ni.com | NI 9997 Getting Started Guide... -
Page 22: Shock And Vibration
Refer to the manual for the chassis you are using for more information about meeting these specifications. Operating temperature -40 °C to 70 °C (IEC 60068-2-1, IEC 60068-2-2) Storage temperature -40 °C to 85 °C (IEC 60068-2-1, IEC 60068-2-2) NI 9997 Getting Started Guide | © National Instruments | 21... -
Page 23: Environmental Management
For additional environmental information, refer to the Minimize Our Environmental Impact web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document. 22 | ni.com | NI 9997 Getting Started Guide... -
Page 24: Worldwide Support And Services
China RoHS compliance, go to ni.com/environment/rohs_china Worldwide Support and Services The NI website is your complete resource for technical support. At ni.com/support, you have access to everything from NI 9997 Getting Started Guide | © National Instruments | 23... - Page 25 United States, create your service request at ni.com/support or dial 1 866 ASK MYNI (275 6964). For telephone support outside the United States, visit the Worldwide Offices section of 24 | ni.com | NI 9997 Getting Started Guide...
- Page 26 NI 9997 Getting Started Guide | © National Instruments | 25...
- Page 27 U.S. Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015. © 2014—2017 National Instruments. All rights reserved. 376997D-01 November 13, 2017...
Need help?
Do you have a question about the 9997 and is the answer not in the manual?
Questions and answers