With Muir’s commitment to quality and use of superior materials and processes we know you will be pleased with your investment, and rest assured that through the correct installation, operation, and maintenance your new Muir Windlass will give you years of reliable performance.
Page 4
EASYWEIGH SERIES – CAPSTAN VC800 INTENDED USAGE This product is exclusively intended for the application as a mooring capstan and as agreed on at the time of quote and order. Any other or extended form of use does not comply with this definition of intended use. The intended use includes compliance with this documentation and other applicable documents to avoid malfunctions and damage in operation.
EASYWEIGH SERIES – CAPSTAN VC800 INSTALLATION INSTRUCTIONS Figure(i) Locate the capstan in a suitable position on the deck so there is no interference from other ropes or objects. Ensure that the rope has a clear lead to the capstan. Make sure that the capstan is in a position so that the rope source is as close to perpendicular as possible.
EASYWEIGH SERIES – CAPSTAN VC800 CAPSTAN LOCATION Capstans should generally be located near the aft quarter of the vessel close to bollards or cleats and appropriate fair leads. The capstan should be aligned so that the mooring ropes can easily lead from the fairlead on to the bottom of the capstan drum for ease of wrapping the rope around the drum 3 or 4 times.
EASYWEIGH SERIES – CAPSTAN VC800 Rotation : Windlasses may be wired for single or dual direction, using single or dual deck switches for raising or lowering. Alternatively, a remote-control solenoid packages with Toggle Switch, Hand Pendant or Auto Anchors are available. Solenoid Installation (Required for Deck Switches) We recommend that the solenoid is installed in an upright position, where it has minimal exposure to sea water and in...
Page 8
EASYWEIGH SERIES – CAPSTAN VC800 CAUTON: NOT TO BE USED AS WIRING DIAGRAMS BUILT TO LAST SINCE 1968 8...
If the line slips check the tension on the finger and increase spring tension. HYDRAULIC MOTOR Refer any problems with your hydraulic motor to a Muir service agent or Muir Hobart. FREEFALL MECHANISM (For Freefall Anchor Winches only) Check that the freefall plunger and spring can move freely.
Line Care (For Rope/Chain Gypsies only) Using the wrong type of line may cause the line to jam causing excessive line wear. Muir Windlasses are designed to run on a 3-strand nylon line (supplied by Muir) which has been specially treated with fabric softener to prevent it from hardening.
EASYWEIGH SERIES – CAPSTAN VC800 VC800 OPERATING INSTRUCTIONS Always keep well clear of the capstan drum when releasing or retrieving rope and/or WARNING: anchor chain. Keep fingers, hair, and clothing well clear when the windlass or capstan is in operation, particularly around areas where the rope and/or chain enters and leaves the capstan/gypsy.
EASYWEIGH SERIES – CAPSTAN VC800 OPERATING DIAGRAM To operate the capstan, wrap the rope around the drum 3 or 4 times and operate the switch while maintaining a load on the tail of the rope. When lifting light loads such as smaller anchors or sails, three or four turns around CAUTION: the Capstan is sufficient.
EASYWEIGH SERIES – CAPSTAN VC800 MAINTENANCE SCHEDULE INSTALLATION DATE PROCEDURE At Installation See page 4/5 Check all bolts are tight. 6 Months after installation Check Grease tape/anti-corrosion film on Motor /Gear drive Remove chain wheel, clean cones then fully grease and lubricate. 12 months after installation see Maintenance &...
Muir representative. • Muir shall not be responsible for failures due to products being used in applications that are not intended for or exceed the products performance specifications. • For warranty claim, defective product must be returned to Muir for inspection.
Page 18
EASYWEIGH SERIES – CAPSTAN VC800 SCAN FOR MUIR WARRANTY BUILT TO LAST SINCE 1968 18...
Page 19
EASYWEIGH SERIES – CAPSTAN VC800 NOTES ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. BUILT TO LAST SINCE 1968 19...
Page 20
EASYWEIGH SERIES – CAPSTAN VC800 NOTES ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. BUILT TO LAST SINCE 1968 22...
Page 21
Serial Number: Copyright 2023 Muir Engineering Group Pty Ltd. Muir reserves the right to alter specifications without notice. All rights reserved. While all care and attention has been taken in the preparation of this Manual, no responsibility shall be BUILT TO LAST SINCE 1968...
Need help?
Do you have a question about the EASYWEIGH VC800 and is the answer not in the manual?
Questions and answers