Subscribe to Our Youtube Channel
Related Manuals for Truper VICO-55
Summary of Contents for Truper VICO-55
- Page 1 Manual Concrete 5.5 Hp vibrator Power Applies for: Code Model 103237 VICO-55 VICO-55 Read this manual thoroughly CAUTION before using the tool.
-
Page 2: Table Of Contents
Contents CAUTION Technical data Fuel requirements To gain the best performance of the tool, prolong the duty life, General safety warnings for the use of make the Warranty valid if power tools necessary, and to avoid hazards of fatal injuries please read and Safety warnings for the use of concrete understand this Manual before vibrators... -
Page 3: Technical Data
Technical data VICO-55 Code 103237 Description Concrete vibrator Engine power 5.5 Hp Maximum engine speed 3 600 RPM Vibration frequency 3 600 vibrations/min Displacement 163 cc (cm Fuel tank 0.92 gal Oil tank 0.13 gal Shaft length 19.6 ft Vibration head diameter 1.5"... - Page 4 General motor tool safety warnings Keep your work area clean, tidy and well lit. Wear adequate protective safety accessories. CAUTION CAUTION Cluttered and dark areas may cause accidents. Wear eye protection, dust mask, non-skid safety shoes, helmet and ear plugs. These safety gears reduce the risk Never use the tool in explosive areas or in the presence of injury.
-
Page 5: Safety Warnings For The Use Of Concrete Vibrators
Safety warnings for the use of concrete vibrators Fuel Handling • Never smoke near fuel or the refueling area, nor while operating the equipment. • To reduce the risk of fire or burns, handle fuel with care, as it is highly flammable. •... -
Page 6: Parts
Parts Fuel tank Exhaust Air filter cover Spark plug Oil fill Coupling for flexible hose drain connector plug Flexible hose Flexible hose connector Vibrating immersion head Chasis tubular Throttle Choke lever Fuel valve Pull cord handle Switch knob Oil fill Oil drain plug ENGLISH... -
Page 7: Assembly
Assembly Hose Connection • Take out the locking pin (A) from the coupling (B). • Insert the connection (C) of the flexible hose into the coupling. Make sure that the coupling jaws (B) align with those of the connection (C) for a proper assembly. •... -
Page 8: Fuel And Oil
Fuel and oil Oil Refilling (A) Fuel supply (B) • Place the equipment on a flat and level surface. • Place the equipment on a flat, level surface. • Unscrew and remove the oil filling cap. • Ensure the area around the fuel cap is clean and dry. •... -
Page 9: Start Up
Start up Start up CAUTION Before starting the engine, it is crucial to verify the following: • Ensure correct levels of gasoline and oil. • Confirm that the flexible hose is connected to the engine coupling and check the assembly bolt is securely in place. •... -
Page 10: Operation
Operation Proper concrete vibration ensures its compressive strength and the bond between the concrete and its reinforcing structure in slabs, beams, columns, and thin structures. It reduces concrete permeability and trapped air, resulting in a better finish, promoting mix uniformity, and enhancing concrete quality upon hardening. -
Page 11: Maintenance
Maintenance CAUTION • Regular and careful maintenance is • Do not alter safety devices. Check their proper essential to maintain optimal safety levels and functioning regularly. performance of the equipment. • Any worn or damaged parts must be replaced before •... -
Page 12: Fuel Filter
Maintenance Fuel filter Spark plug • The fuel filter plays a crucial role in preventing water or • Before you remove the spark plug (B), make sure to dust particles from entering the carburetor through the clean the area around the base of the spark plug to fuel tank. -
Page 13: Troubleshooting
Troubleshooting Problem Cause Solution The engine does not • The switch is off. • Turn on the switch. start. • There is not enough fuel. • Fill the fuel tank. • Oil level is too low or there is no oil. •... -
Page 14: Notes
Notes ENGLISH... -
Page 15: Authorized Service Centers
Authorized Service Centers In the event of any problem contacting a TRUPER Authorized Service Center, please see our webpage WWW.TRUPER.COM to get an updated list, or call our toll-free numbers 800 690-6990 or 800-018-7873 to get information about the nearest Service Center. -
Page 16: Warranty Policy
It includes the costs of transportation of the product that derive from its fulfillment of its service network. Phone number 800-018-7873. Made in China. Imported by Truper, S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257, Phone number 761 782 9100.
Need help?
Do you have a question about the VICO-55 and is the answer not in the manual?
Questions and answers