Do you have a question about the SMARTWASH+ FH52000G and is the answer not in the manual?
Questions and answers
william McMillian
May 25, 2025
Dry only not working
1 comments:
Mr. Anderson
May 26, 2025
The Dry Only function on the Hoover FH52000G may not be working due to one or more of the following reasons:
1. The Dirty Water Tank is full or not properly secured. 2. The recovery nozzle is not installed correctly. 3. There is a blockage in the nozzle or hose. 4. The debris filter in the Dirty Water Tank is clogged. 5. The unit is not extracting water because the shut-off float in the Dirty Water Tank has been triggered.
Check and correct each of these issues to restore Dry Only function.
Tools and Accessories ........................8 Before You Begin Cleaning ......................9 Getting Started ..........................10 How to Assemble Your SmartWash™ Carpet Cleaner .............10 Using your SmartWash™ Carpet Cleaner .................11 Maintenance ..........................13 Hoover® Professional Series Solution Guide ................20 Troubleshooting ..........................21 Warranty ............................23 French .............................25 Spanish ............................49...
Page 4
• To Reduce the Risk of Fire and Electric Shock due to opening blocked; keep free of dust, lint, hair and internal component damage, use only HOOVER cleaning anything that may reduce air flow. fluid intended for use with this appliance. See the •...
GROUNDING INSTRUCTIONS: nominal 120-volt circuit and has a grounding plug that • Store appropriately indoors in a dry place. Do not expose looks like the plug (A) illustrated in Fig. 1. A temporary machine to freezing temperatures. This appliance must be grounded. If it should malfunction adapter (D) may be used to connect this plug to a 2-pole •...
FlexForce™ Cleaner Tank Handle PowerBrushes 2-in-1 Antimicrobial Tool* Water Accessory Mesh Tool Tank Hose Storage Bag Sample Bottle of Cleaning Solution *Tools and Accessories vary per model. Accessories not included with your model may be purchased separately by visiting Hoover.com...
A. The rubber nub insert is for un- pleasant stain removal and hygienic clean ups B. The bristle insert is for tough scrubbing power *Tools and Accessories vary per model. Accessories not included with your model may be purchased separately by visiting Hoover.com...
Pin up furniture skirts and draperies. flooring and to avoid potential slip hazard, after use (a) Use your Hoover carpet cleaner only if Pretreat spots and heavy traffic areas with do not leave the product on wood and laminate surfaces upholstery fabric is marked with a “W”...
Remove the cap and add Remove the cap and fill Wrap the power cord warm water to the top of with Hoover® Cleaning around the cord hooks for tank. Replace cap. Solution to the top of the convenient storage.
Using Your SmartWash™ Carpet Cleaner Unwrap the power cord and Step on the Power Pedal plug unit in an electrical to turn ON. outlet. Step on the Handle Release Pedal to recline the unit for cleaning position.
Page 12
Continue in this mode until little water is visibly passing through the nozzle. For best results, Hoover Slowly pull backward. The unit recommends rinsing the carpet will automatically dry your with clean water only. This carpets by extracting the water.
Maintenance How to Empty Place on a flat surface and Turn the cleaner off and unlatch Dirty Water Tank lid unplug from electrical to remove top of tank. outlet. Empty tank, rinse, wipe filter clean and allow to air dry. Grab the Dirty Water Tank handle and pull up to release.
Page 14
Continue using dry strokes until little water is visible passing through the nozzle. For best results, Hoover recommends rinsing carpet with water only. This removes residual carpet cleaning solution. Remove Solution Tank and repeat. For heavily soiled areas, repeat.
Page 15
Maintenance How to Remove and Clean Nozzle To prevent possible leaking, Rinse debris from Nozzle. Slide Nozzle forward to remove and empty Clean snap into position. Water Tank, Dirty Water Tank and Solution Tank. With handle in upright Position Nozzle onto foot, position, lift up on the making sure to align the Nozzle release then pull...
Maintenance How to Change and Clean Brushes HOW TO REMOVE HOW TO REPLACE Grab Side A and pull up At an angle, align side To prevent possible to remove. Repeat on the B on the brush to the leaking, remove Clean other brush.
Page 17
Unit may lose suction if not Read “Before You Begin Cleaning” instructions. closed properly. Be sure to check Hoover Cleaning Guide on page 20 and the cleaning code on your upholstery. Use your cleaner only on upholstery marked “W” or “W/S”.
Page 18
Tools and Accessories How to Attach Tools To ensure maximum Using your thumb, push performance and to protect forward and up on the latch your carpet, be sure to to remove tool. place the handle in the upright position while using the hose.
Page 19
You will also without pressing trigger. see the float rise and shut off suction Fill Solution Tank with Hoover® solution Overlap strokes by ½ inch to help at the same time. according to instructions.
For best results, use your Carpet Cleaner + Spot Treatment + Solutions. Hoover has a full line of Detergents and Spot Treatments to complement your Hoover carpet cleaner and the specific condition of your carpet. To prevent project interruption, keep Detergent on hand and store with your carpet cleaner.
Page 21
PLUS CARPET SOLUTIONS CLEAN PLUS™ CLEAN PLUS™ PET PLUS™ PET PLUS™ PRO PLUS™ CARPET WASHER DETERGENT SPOT SPRAY CARPET WASHER DETERGENT SPOT SPRAY CARPET WASHER DETERGENT Powerful cleaner for everyday dirt and Powerful spot spray for everyday Powerful cleaner enhanced with enzymes Powerful spot spray enhanced with Professional strength carpet &...
To reduce the risk of personal injury - Unplug before cleaning or servicing. WARNING To reduce risk of fire and electric shock due to internal component damage, use only Hoover cleaning products intended for use with the appliance as noted.
Page 23
PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION Cleaner won’t run 1. Not firmly plugged in 1. Plug unit in firmly. 2. No voltage in wall plug 2. Check fuse or breaker in home. 3. Blown fuse or tripped breaker 3. Replace fuse or reset breaker in home. 4.
SERVICE & WARRANTY SERVICE INFORMATION Remanufactured, refurbished, or reconditioned products have a limited warranty as determined by the retailer selling the product to you. This product is warranted against failure due to a defect in materials or workmanship from the date of original purchase. Proof of the original purchase date is needed to make a warranty request or claim.
Need help?
Do you have a question about the SMARTWASH+ FH52000G and is the answer not in the manual?
Questions and answers
Dry only not working
The Dry Only function on the Hoover FH52000G may not be working due to one or more of the following reasons:
1. The Dirty Water Tank is full or not properly secured.
2. The recovery nozzle is not installed correctly.
3. There is a blockage in the nozzle or hose.
4. The debris filter in the Dirty Water Tank is clogged.
5. The unit is not extracting water because the shut-off float in the Dirty Water Tank has been triggered.
Check and correct each of these issues to restore Dry Only function.
This answer is automatically generated