Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kwikset HALO SELECT
Summary of Contents for Kwikset HALO SELECT
- Page 1 English 53861-001 Rev 01 Installation and Reference Guide...
- Page 2 Welcome to the Kwikset family! This guide will get you up and running with your new Halo Select. If you have any issues, please visit our kwikset.com/support support center: or call us at 1-800-327-5625.
-
Page 3: Getting Started
Getting started For an interactive version of this installation guide, please download the Kwikset app: kwikset.com/app... - Page 5 Table of contents Parts in the box ..........4 Required tools ..........5 Installation ............7 Download the app ........17 Reference guide ..........19...
-
Page 6: Parts In The Box
Parts in the box Exterior assembly Interior assembly Interior cover 03809 Latch Batteries 46780 Door sensor magnet Strike... -
Page 7: Required Tools
Required 64844 tools Mounting plate 52502 Keys Phillips head SmartKey™ screwdriver Ruler tool No electric drills... -
Page 8: Installation
Installation... - Page 9 Measure door thickness 1-3/4” to 2” (44mm - 51mm) If door thickness is greater than 2” (51mm) contact Kwikset customer service at 1-800-327-5625. Your installation will require a thick door installation kit.
- Page 10 Your new lock will only support a door thickness 2-1/8” of 1-3/4” to 2” (44mm to (54mm) 51mm) and a door bore hole diameter of 2-1/8” (54mm). If drilling a new door, use the supplied template and instructions available at: kwikset.com/doorprep...
-
Page 11: Install The Latch
Install the latch Extend the latch bolt. If your door requires a drive-in latch, please contact Kwikset at 1-800-327-5625. UP is on top. 03809* (2X) If the D-shaped hole is not centered in the bore hole, rotate the latch face to extend the latch. - Page 12 Install the strike and sensor magnet DOOR JAMB 46780* (4X) 1" (25 mm) *Install the longer hole depth screws closest to the door jamb. Peel the liner Place magnet from magnet. above the Press strike. 3/4” firmly Ensure (20mm) for 10 surface is seconds.
- Page 13 Install the exterior assembly [OUTSIDE] Cable goes under the latch.
- Page 14 [INSIDE] [INSIDE] Keep parallel to the door edge Tighten the screws evenly. Tighten the screws evenly. DO NOT over-tighten. 64844 64844 (2X) (2X) [OUTSIDE] Route the cable Insert the key and through the bottom test the latch. If the hole of the mounting latch does not extend plate.
- Page 15 Install the interior assembly Remove the interior cover from the interior assembly. Make sure to remove the battery pack before installing interior assembly. Press down on tab to release the battery pack, and pull out. If the turnpiece is not pointing up, rotate the turnpiece until it’s in a vertical position.
- Page 16 Connect the cable. Ensure a tight cable connection. Secure the interior assembly onto the mounting plate. Lay cable flat inside the bottom of the interior housing. 52502 (2X) Ensure the spindle fully engages with the turnpiece shaft. Ensure cable remains [INSIDE] connected.
- Page 17 Install batteries and battery pack With the door open, install the battery pack. NOTE: Lock must be installed on the door Insert (4) AA batteries (included) before inserting the batteries. into the battery tray. Ensure correct polarity. Use new, non-rechargeable alkaline batteries only.
- Page 18 Download the Kwikset app & create an account to complete set up...
- Page 19 Follow the set up instructions in the Kwikset app to complete your lock set up. kwikset.com/app The Kwikset app is needed to use this lock. If this lock was professionally installed (or installed by someone other than the homeowner), make sure...
-
Page 20: Reference Guide
Reference Guide... - Page 21 Locked Unlocked To unlock your door, enter your access To lock your door, press the lock icon. code. The bolt will retract, then the The bolt will extend, then the screen screen will display the Unlocked LED will display the Locked LED Indicator Indicator and play the unlocked tone.
- Page 22 SmartKey® Re-key Re-key the lock to work with your existing key by following the SmartKey® Re-key instructions. NOTE: If Auto-Lock is enabled, remove the battery pack before re-keying your lock.
- Page 23 Exterior LED Indicators Amber: Green: Alternating Red flashing: Locked Unlocked Lock Jammed Red: Red: Red: Lockout Low Battery Invalid Credentials...
- Page 24 Interior Status LED Indicators Amber Green Slow Blinking: Slow Blinking: Locked Unlocked Blinking: Low Battery...
-
Page 25: Factory Reset
• reset lock settings to default • you have lost your phone • lock will show as o ine in the Kwikset App • you are troubleshooting the • lock will be deactivated and lock will need to be set up as new 1. - Page 26 3. After 30 seconds, the Status LED 4. Press the Programming Button light will flash RED and lock will once within 5 seconds of the beep. Release the Programming Status LED light displaying RED to Button. confirm factory reset. Status 5.
-
Page 27: Troubleshooting
Halo Select at a Glance Exterior Interior (cover removed) Connectivity Icon Warning Icon Battery Status Icon Button A Keypad Pairing Programming Button Checkmark Button Icon Lock Keyway Icon SmartKey™ tool access Troubleshooting If you have any issues, please visit our kwikset.com/support... -
Page 28: Important Safeguards
Important Safeguards 1.. Read all instructions in their entirety. 5. If using the Auto-Lock features, make sure you have your smartphone or standard key with you 2. Familiarize yourself with all warning and to prevent locking yourself out. caution statements. 6.
Need help?
Do you have a question about the HALO SELECT and is the answer not in the manual?
Questions and answers