Advertisement
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
•
To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and
other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.
•
Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
•
Installation and service of luminaires should be performed by a qualified licensed electrician.
•
Maintenance of the luminaires should be performed by person(s) familiar with the luminaires' construction and operation
and any hazards involved. Regular fixture maintenance programs are recommended.
•
It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient
dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a solution of warm
water and any mild, non‐abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly
become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.
•
DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been
damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
•
Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
•
These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency
to meet in connection with installation, operation, or maintenance. Should further information be desired or should
particular problems arise which are not covered sufficiently for the purchaser's or owner's purposes, this matter should be
referred to Acuity Brands Lighting, Inc.
WARNING
RISK OF ELECTRIC SHOCK
Disconnect or turn off power before
installation or servicing.
Verify that supply voltage is correct by
comparing it with the luminaire label
information.
Make all electrical and grounded
connections in accordance with the National
Electrical Code (NEC) and any applicable
local code requirements.
All wiring connections should be capped
with UL approved recognized wire
connectors.
Install this kit only in the luminaires that has
the construction features and dimensions
shown in the drawings.
Do not alter, relocate or remove wiring,
lamp holders, power supply or any other
electrical component.
Do not make or alter any open holes in an
enclosure of wiring or electrical components
during kit installation.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
LED IMPORTANT SAFETY INSTRUCTIONS
Allow lamp/fixture to cool before handling.
Do not touch enclosure or light source.
Do not exceed maximum wattage marked on
luminaire label.
Follow all manufacturer's warnings,
recommendations and restrictions for: driver
type, burning position, mounting
locations/methods, replacement and
recycling.
Keep combustible and other materials that
can burn, away from lamp/lens.
Do not operate in close proximity to persons,
combustible materials or substances
affected by heat or drying.
WARNING
RISK OF BURN
CAUTION
RISK OF FIRE
IM-351-A
Advertisement
Table of Contents
Related Manuals for Acuity Brands Holophane ESPLANADE
Summary of Contents for Acuity Brands Holophane ESPLANADE
- Page 1 LED IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION • To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels. • Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions. • Installation and service of luminaires should be performed by a qualified licensed electrician. • Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards involved. Regular fixture maintenance programs are recommended. • It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a solution of warm water and any mild, non‐abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary. • DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced. •...
-
Page 2: Risk Of Injury
LED IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF INJURY Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance. Avoid direct eye exposure to the light source while it is on. CAUTION: RISK OF PRODUCT DAMAGE Never connect components under load. Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation. Unless individual product specifications deem otherwise: Never connect an LED product directly to a dimmer packs, occupancy sensors, timing devices, or other related control devices. LED fixtures must be powered directly off a switched circuit. Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for some volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or conduction cooling. Unless individual product specifications deem otherwise: Do not exceed fixtures maximum ambient temperature. Only use fixture in its intended location. LED products are Polarity Sensitive. Ensure proper Polarity before installation. Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of the unit. Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance. Some components inside the fixture may not be serviceable. In the unlikely event your unit may require service, stop using the unit immediately and contact an ABL representative for assistance. Always read the fixtures complete installation instructions prior to installation for any additional fixture specific warnings. Please see product specific installation instructions for additional warnings or any applicable FCC or other regulatory statements. -
Page 3: Installation
HOLOPHANE ® Pedestrian LED Installation and Luminaire Series Maintenance Retrofit Kit Manual AFTER INSTALLATION DELIVER THIS MANUAL TO OWNER ESPLANADE® MEMPHIS GR395, GR804A 1 INTRODUCTION CAUTION: 1.1 Product Description. THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A • LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION The fixture line is designed to operate LED light sources up to SHALL BE DETERMINDED BY CSA OR AUTHORITES HAVING... - Page 4 channel and the gasket alignment tab is inserted into the 2.2.4 Remove the refractor assembly from the electrical housing indentation on the LED mounting plate. See Figures 2 and 3. by loosening the wing nut, disengaging the closure bolt, and then swinging the refractor assembly open on the electrical housing 2.2.12 Place the door over the refractor flange and secure to the...
-
Page 5: Electrical Component Replacement
assembly closed, engage the closure bolt and tighten the wing nut 3.2 Electrical Component Replacement. securely. See Figure 4. 3.2.1 Wipe off exterior dirt and debris. 2.2.14 If the fixture has a skirt option, remove it from the original door and install it onto the retrofit door using the original screws. NOTE The entire fixture below the mounting assembly may be removed 2.2.15... -
Page 6: Limited Warranty And Limitation Of Liability
Figure 5 GR2203 4 Limited Warranty and Limitation of Liability The Holophane limited warranty and limitation of liability is published in the "Terms and Conditions" section of the current Holophane buyer's guide, and is available from your local Holophane sales representative. Failure to properly install this Unit will void all Warranties.
Need help?
Do you have a question about the Holophane ESPLANADE and is the answer not in the manual?
Questions and answers