Acuity Brands AEL American Revolution 247 Series Installation Instructions

AMERICAN REVOLUTION POST TOP 247 LED SERIES
DISCONNECT POWER BEFORE RELAMPING OR WIRING THE FIXTURE.
HOUSING MUST BE GROUNDED TO REDUCE POTENTIAL OF ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION,
CUPOLA LENS CUPOLA LENS
ADJUST PHOTO- ADJUST PHOTO-
CONTROL BY LIFTING CONTROL BY LIFTING
& TURNING CUPOLA & TURNING CUPOLA
SIMULTANEOUSLY SIMULTANEOUSLY
HOOD HOOD
TRIGGER TRIGGER
LATCH LATCH
-OPTIONAL- -OPTIONAL-
LENS LENS
PANELS (4) PANELS (4)
NEMA NEMA
LABEL HERE LABEL HERE
-OPTIONAL- -OPTIONAL-
LADDER REST (2) LADDER REST (2)
-OPTIONAL- -OPTIONAL-
SET SCREWS (3) SET SCREWS (3)
FIGURE 1 FIGURE 1
CLOSED HOOD - STREET SIDE VIEW CLOSED HOOD - STREET SIDE VIEW
LENS LENS
PANELS (4) PANELS (4)
OPEN HOOD - TOP VIEW OPEN HOOD - TOP VIEW
DRAWING NO. A72881 REV A
American Electric Lighting a division of Acuity Lighting Group, Inc. Newark, OH
INSTALLATION INSTRUCTIONS
CONSULT LOCAL CODE AUTHORITY
CAUTION
LIFT UNIT OUT OF BOX BY BAG, NOT CUPOLA
!
CUPOLA CAP CUPOLA CAP
CUPOLA BASE CUPOLA BASE
CLOSURE CLOSURE
SCREW SCREW
BOSS BOSS
SCREW NOT SCREW NOT
SHOWN SHOWN
LOWER HOUSING LOWER HOUSING
MIN POLE OD 2.375" MIN POLE OD 2.375"
MAX POLE OD 3" MAX POLE OD 3"
FIGURE 2 FIGURE 2
(FRONT)
TM
WARNING
!
WARNING
!
CAUTION
!
1. TO OPEN THE FIXTURE, LOCATE THE CLOSURE SCREW. TO OPEN THE FIXTURE, LOCATE THE CLOSURE SCREW.
IT IS LOCATED ON THE STREET SIDE OF THE FIXTURE. IT IS LOCATED ON THE STREET SIDE OF THE FIXTURE.
(SEE FIGURE 1.) (SEE FIGURE 1.)
2. UNSCREW THE IS CAPTIVE CLOSURE SCREW. YOU WILL 2. UNSCREW THE IS CAPTIVE CLOSURE SCREW. YOU WILL
KNOW KNOW T THE SCREW HE SCREW IS IS COMPLETELY DISENGAGED FROM
THE HOOD WHEN THE HOOD
DOWN. DOWN.
3. OPEN THE HOOD. 3. OPEN THE HOOD.
4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE HOOD AND RE- 4. TO CLOSE THE FIXTURE, SIMPLY CLOSE THE
TIGHTEN THE CAPTIVE CLOSURE SCREW. TIGHTEN THE CAPTIVE CLOSURE SCREW.
NOTE FOR OPTIONAL TRIGGER LATCH: TO OPEN THE UNIT NOTE FOR OPTIONAL
SIMPLY PULL TRIGGER WITH YOU SIMPLY PULL
PUSHING UP ON THE HOOD WITH YOUR THUMBS. CLOSE PUSHING UP ON THE HOOD WITH YOUR
THE UNIT BY CLOSING THE HOOD AND PRESSING THE UNIT BY
UNTIL THE TRIGGER LATCH UNTIL THE TRIGGER
1. OPEN THE UNIT AND REMOVE THE STREET SIDE LENS. (SEE 1. OPEN THE UNIT AND REMOVE THE STREET SIDE LENS. (SEE
FIGURE 2). FIGURE 2).
2. LOCATE THE WIRING DIAGRAM ATTACHED TO THE 2. LOCATE THE WIRING DIAGRAM ATTACHED TO THE
INSIDE OF THE HOOD. INSIDE OF THE HOOD.
3. PULL UP THE TERMINAL BLOCK COVER. 3. PULL UP THE TERMINAL BLOCK COVER.
4. USING THE WIRING DIAGRAM AS A GUIDE, CONNECT 4. USING THE WIRING DIAGRAM AS A GUIDE, CONNECT
THE POWER SUPPLY LEADS TO TEH TERMINAL BLOCK. (SEE THE POWER SUPPLY LEADS TO TEH TERMINAL BLOCK. (SEE
FIGURE 2). FIGURE 2).
5. CONNECT THE GREEN OR BARE GROUND SUPPLY WIRE 5. CONNECT THE GREEN OR BARE GROUND SUPPLY WIRE
LOWER LOWER
HOUSING HOUSING
TO THE CASTING BY HOOKING IT AROUND THE HEAD OF TO THE CASTING BY HOOKING IT AROUND THE HEAD OF
THE GREEN GROUNDING SCREW, LOCATED BESIDE THE THE GREEN GROUNDING SCREW, LOCATED BESIDE THE
TERMINAL BLOCK, AND TIGHTENING THE SCREW TERMINAL BLOCK, AND TIGHTENING THE SCREW
SECURELY. SECURELY.
6. PUSH DOWN THE TERMINAL BLOCK COVER. 6. PUSH DOWN THE TERMINAL BLOCK COVER.
5. REINSTALL THE STREET SIDE LENS. 5. REINSTALL THE STREET SIDE LENS.
6. CLOSE THE UNIT. 6. CLOSE THE UNIT.
©2013 ACUITY LIGHTING GROUP, INC.
OPENING & CLOSING THE UNIT: OPENING & CLOSING THE UNIT:
COMPLETELY DISENGAGED FROM
WHEN THE SCREW CAN MOVE FREELY UP AND THE SCREW CAN MOVE FREELY UP AND
TRIGGER LATCH: TO OPEN THE UNIT
TRIGGER WITH YOUR INDEX FINGER WHILE INDEX FINGER WHILE
CLOSING THE HOOD AND PRESSING DOWN
LATCH ENGAGE. ENGAGE.

WIRING:

WIRING:
HOOD AND RE-
THUMBS. CLOSE
DOWN
PART NUMBER 057-70-72881