Table of Contents
Advertisement
Quick Links
Installation Instructions
Sintesis™ Chiller Louvered Panel
Kit Selection and Installation
RTAF
Model Numbers:
RTAF150
RTAF170
RTAF180
RTAF200
This document applies to service offering applications only.
Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of
heating, ventilating, and air-conditioning equipment can be hazardous and requires specific knowledge and training.
Improperly installed, adjusted or altered equipment by an unqualified person could result in death or serious injury.
When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that are
attached to the equipment.
August 2023
RTAF215
RTAF230
RTAF250
SAFETY WARNING
SO-SVN018A-EN
Advertisement
Table of Contents
Related Manuals for Trane Sintesis RTAF Series
Summary of Contents for Trane Sintesis RTAF Series
- Page 1 Installation Instructions Sintesis™ Chiller Louvered Panel Kit Selection and Installation RTAF Model Numbers: RTAF150 RTAF215 RTAF170 RTAF230 RTAF180 RTAF250 RTAF200 This document applies to service offering applications only. SAFETY WARNING Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air-conditioning equipment can be hazardous and requires specific knowledge and training.
-
Page 2: Warnings, Cautions, And Notices
When working with or around hazardous chemicals, these compounds have the same potential impact to the ALWAYS refer to the appropriate SDS and OSHA/GHS environment. Trane advocates the responsible handling of all (Global Harmonized System of Classification and refrigerants. Labeling of Chemicals) guidelines for information on... -
Page 3: Revision History
Copyright This document and the information in it are the property of Trane, and may not be used or reproduced in whole or in part without written permission. Trane reserves the right to revise this publication at any time, and to make changes to its content without obligation to notify any person of such revision or change. -
Page 4: Pre-Installation
Pre-Installation Introduction Table 3. Kit number KIT17977 The following instructions show the kit selection and Component installation of the Sintesis™ RTAF louvered panels. Part Component Description 57227970001 BRACKET; SIDE; RTAF LOUVER OPT Kit Selection X25020604010 SCREW; HEX HD CAP THD ROLL M8 x 16MM 572280880001 BRACKET;... -
Page 5: Installation
Installation NOTICE WARNING Equipment Damage! Hazardous Voltage! Using an impact gun when installing plastic louvers Failure to disconnect power before servicing could could result in equipment damage. Do NOT use an result in death or serious injury. impact gun when installing plastic louvers. Disconnect all electric power, including remote disconnects before servicing. - Page 6 Installation Figure 2. RTAF louvered panels 2. Install left end side louver bracket (Figure 2, Item 3) and right end side louver bracket (Figure 2, Item 4) in between the connector post bracket and corner posts on both sides of unit with four M8 x 16mm screws (Figure 2, Item 2).
- Page 7 Installation Figure 4. RTAF louvered panels 5. Install side louver panels on both sides of unit (Figure Item 7) with six 6 MM thread roller screws (Figure 4, Item 8). Bottom two holes in base rail may need to be drilled if not present (5.2 mm).
- Page 8 Installation Figure 6. RTAF louvered panels NOTICE Equipment Damage! Using an impact gun when installing plastic louvers could result in equipment damage. Do NOT use an impact gun when installing plastic louvers. 8. Position lower louvers (Figure 6, Item 11) beneath upper side panel and secure with four M8 x 16mm screws (Figure 6, Item 2) on the top of the lower panel.
- Page 9 Installation Figure 7. RTAF louvered panels 12. Set both upper end louvers (Figure 7, Item 13 and 14) in 14. Install both upper end louver panels with nine M8 x 16mm place using the weld studs on the control panel as a guide. screws (Figure 7, Item 2).
- Page 10 Installation 15. Install back louver bracket (Figure 8, Item 15) between corner posts opposite the control panel end with four M8 x 16mm screws (Figure 8, Item 2). Figure 9. RTAF louvered panels 16. Install back panel (Figure 9, Item 16) with nine M8 x 16mm screws (Figure 9, Item 2) on left side.
- Page 11 Installation 18. Install two S type clips (Figure 10, Item 6) in square holes on the top end cross member channel. Figure 11. RTAF louvered panels 19. Hang upper louver (Figure 11, Item 9) off of S type clips. Figure 12. RTAF louvered panels 20.
- Page 12 For more information, please visit trane.com or tranetechnologies.com. Trane has a policy of continuous product and product data improvement and reserves the right to change design and specifications without notice. We are committed to using environmentally conscious print practices.
Need help?
Do you have a question about the Sintesis RTAF Series and is the answer not in the manual?
Questions and answers