Advertisement
BEFORE YOU BEGIN
BEFORE YOU BEGIN
·
Observe all local plumbing and building codes.
·
Prior to installation, unpack the new lavatory and inspect it
for damage. Return the lavatory to its protective carton
until you are ready to install it.
·
These instructions are for installing the lavatory to wood
frame construction. For other installation, supply suitable
bracing and fastening devices of sufficient size and strength.
·
The walls and floor must be square, plumb, and level.
CAUTION:
Lavatory must be installed with either the
pedestal or half pedestal. It must not be installed alone.
·
Kohler lavatory is made according to American National
Standard that it can match the American lavatory fittings.
Any other lavatory fittings may not fit for kohler lavatory.
ROUGHING-IN
(S) Supply (Based on 305mm (12") riser which may require
cutting).
K-2017T-1/-4, K-11341T-1/-4=254mm (10");
K-2017T-8, K-11341T-8=356mm (14").
(T) Pop-up drain typically 356mm (14"); drain typically 333mm
(13-1/8").
Fixture dimensions are nominal and conform to tolerances in
ASME Standard A112.19.2M.
(T)
DN 15 HOT
1037277-T01-A
K-2017T-1/K-11341T-1
610
45
35
464
(S)
102
DN 15 COLD
32 OUTLET
VITREOUS CHINA HALF PEDESTAL LAVATORY
·
·
·
·
·
(S)
(
K-2017T-1/-4, K-11341T-1/-4=254mm (10")
K-2017T-8, K-11341T-8=356mm (14")
(T)
A112.19.2M
K-2017T-4/K-11341T-4
76
188
479
K-2017T-8/K-11341T-8
10
128
214
(S)
14 D. ANCHOR
HOLESIN
869
LAVATORY
528137
-1-
INSTALLATION INSTRUCTIONS
VITREOUS CHINA PEDESTAL LAVATORY
305mm
356mm
102
32
102 102
35
35
108
ã
ã
Copyright Kohler China Ltd., 2004
K-2017T-1/-4/-8
K-11341T-1/-4/-8
)
333mm
(ASME)
UNIT: mm
Fig. #1
1
, 2004
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kohler FOLIO K-11341T-1
Summary of Contents for Kohler FOLIO K-11341T-1
- Page 1 · Kohler lavatory is made according to American National Standard that it can match the American lavatory fittings. Any other lavatory fittings may not fit for kohler lavatory. ROUGHING-IN (S) Supply (Based on 305mm (12") riser which may require 305mm cutting).
-
Page 2: Tools And Materials Required
K-11341T-1/4/8 Fig. #2 TOOLS AND MATERIALS REQUIRED (Not Supplied) · · Level · · Drill with assorted bits · · 14mm 14mm(9/16") Wrench · · Tape measure · · Framing square · · Channel lock pliers · · 203mm Socket wrench with 203mm (8") extension & assorted sockets MATERIALS REQUIRED (Not Supplied) ·... -
Page 3: Installations
INSTALLATIONS INSTALLATION K-2017T-1/- K-2017T-1/-4/-8 4/-8 Ridge Leveling Pads Ridge · · Rough-in the supplies and the drain piping. Leveling Pads NOTE: The supply stop handles Ridge 76mm cannot extend more than 76mm (3") from the finished wall when in the Leveling Pads open position. - Page 4 · · Position the pedestal mounting hole over the hole in the floor. Screw · Secure the pedestal to the floor · with the screw and washer. Tighten Pedestal the screw until it is snug. For masonry applications, use suitable anchor.
- Page 5 · · Mark the centerline (along the hanger) on the wall and set the Bolts Finished Wall lavatory on the hanger along the centerline, then level the lavatory. · · Mark the mounting holes on the wall, then remove the lavatory carefully.
-
Page 6: Important Consumer Information
LIMITED ONE-YEAR WARRANTY Plumbing Fixtures and Fittings Limited One-year Warranty Kohler plumbing fixtures and fittings are warranted to be free of manufacturing defects. This product is warranted for one year from date of purchase. Kohler China will be responsible for any problems caused by manufacturing defects provided with the invoice.
Need help?
Do you have a question about the FOLIO K-11341T-1 and is the answer not in the manual?
Questions and answers