Related Manuals for Feider Machines FM1125-A
Summary of Contents for Feider Machines FM1125-A
- Page 1 ORIGINAL INSTRUCTIONS >EN ANGLE GRINDER 1050W FM1125-A USE GUIDE CAUTION: Read the instructions before using the product.
-
Page 2: Table Of Contents
CONTENTS SAFETY INSTRUCTIONS PRODUCT DESCRIPTION SPECIFICATION REPLACEMENT OF PARTS AND MAINTENANCE DISPOSAL DECLARATION OF CONFORMITY WARRANTY PRODUCT FAILURE WARRANTY EXCLUSIONS... -
Page 3: General Power Tool Safety Warnings
1. SAFETY WARNINGS GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool"... -
Page 4: Safety Instructions For All Operations
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. -
Page 5: Further Safety Instructions For All Operations
power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time. -
Page 6: Additional Safety Instructions For Grinding And Cutting-Off Operations
Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback. e) Do not attach a saw chain woodcarving blade, segmented diamond wheel with a peripheral gap greater than 10mm or toothed saw blade. Such blades create frequent kickback and loss of control. ADDITIONAL SAFETY INSTRUCTIONS FOR GRINDING AND CUTTING-OFF OPERATIONS Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operation a) Use only wheel types that are specified for your power tool and the specific guard designed for the... -
Page 7: Product Description
workpiece causing poor control. b) When using a grinding wheel guard for cutting-off operating with the bonded abrasive wheels, there is an increased risk of exposure to emitted sparks and particles, as well as exposure to wheel fragments in the events of wheel burst. c) Only use the abrasive wheels which are recommended in this manual. -
Page 8: Specification
3. SPECIFICATION Rated voltage 230-240V~, 50Hz Rated power 1050W Rated no-load/ no: 11000/min Spindle thread Φ125mm Max. Disc diameter Degree of Protection: IPX0 Protection class: II (double insulation) Weight (without sander disc and dust collection box) 2,0 kg Noise emission value according to EN 62841-2-4 Sound pressure level L 87,8 dB(A), K= 3dB(A) Sound power level L... -
Page 9: Operation
1) Installation of the guard o Put the protective guard (6) in the correct position (see below Fig. 1). o Turn the guard to correct position (see below Fig. 2). o Screw it firmly the guard. (see below Fig. 3). Fig.1 Fig.2 Fig.3... -
Page 10: Replacement Of Parts And Maintenance
purposes, avoid tilting it in the cutting plane. The cutting wheel must have a clean cutting edge. A diamond cutting wheel is best used to cut hard stone. It is prohibited to use the machine on asbestos materials! o Never use a cutting wheel for rough grinding. Replace the disk (Fig.6) Beware –... -
Page 11: Disposal
o Store the tool in a clean, dry place, preferably in its box. o When transporting and storing, always put the protective cover on the blade. o The tool should be stored away from children and pets. o Avoid exposing the tool to direct sunlight. 6. -
Page 12: Warranty
8. WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. It can be extended by one year if the user subscribes to website of myswap. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. -
Page 13: Product Failure
9. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: • Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. •... -
Page 14: Warranty Exclusions
10. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •... - Page 15 BUILDER SAS 32, rue Aristide Bergès - ZI 31270 Cugnaux – France Made in PRC 2022...
Need help?
Do you have a question about the FM1125-A and is the answer not in the manual?
Questions and answers