Related Manuals for Feider Machines FM20V115-A
Summary of Contents for Feider Machines FM20V115-A
- Page 1 ORIGINAL INSTRUCTIONS >EN CORDLESS ANGLE GRINDER FM20V115-A USER GUIDE CAUTION: READ THE INSTRUCTIONS BEFORE USING THE MACHINE...
-
Page 2: Table Of Contents
CONCENTS INTENDED USE SAFETY INSTRUCTIONS SYMBOLES YOUR PRODUCT PACKAGE CONTENT LIST OPERATIONS CLEANING AND MAINTENANCE TECHNICAL DATA SERVICE DEPARTMENT STORAGE DISPOSAL DELARATION OF CONFORMITY WARRANTY PRODUCT FAILURE WARRANTY EXCLUSIONS... -
Page 3: Intended Use
1. INTENDED USE This machine is developed for grinding and roughing of metal and stone. With correct accessories the machine can also be used for brushing and sanding. It is not designed for commercial use. WARNING! For your own safety, read this manual and the general safety instructions carefully before using the appliance. - Page 4 b) Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.
- Page 5 NOTE The temperature „130 °C“ can be replaced by the temperature „265 °F“. g) Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.
- Page 6 l) Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control. m) Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.
- Page 7 ⚫ Before use, inspect the grinding disc for any damage. Do not use grinding discs which are cracked, ripped or otherwise damaged. ⚫ Before use, let the machine run idle for 30 seconds. ⚫ Immediately switch off the machine in case of abnormal vibrations or occurrence of another defect. Carefully inspect the machine and grinding disc before switching the machine on again.
-
Page 8: Symboles
Consult a physician. Fire hazard! Avoid short-circuiting the contacts of a detached battery. Do not incinerate the battery. Charger Only use the model of charger recommended. See the technical data. 3. SYMBOLS Conforms to relevant safety standards To reduce the risk of injury, the user must read and understand this manual before using this product. -
Page 9: Your Product
4. YOUR PRODUCT 1. Lock lever for protection guard 7. Guard 2. Spindle lock button 8. Grinding disc (not included) 3. Main handle 9. Speed adjuster 4. On/Off switch 10. Release button 5. Air vents 11. Battery pack (Not included) 6. -
Page 11: Package Content List
5. PACKAGE CONTENT LIST ◼ Remove all packaging materials. ◼ Remove remaining packaging and packing inserts (if included). ◼ Check that the package contents are complete. ◼ Check the appliance, the power cord, the power plug of charger and all accessories for transportation damage or not. - Page 12 The battery has approx 75% remaining charge. 2 LED(s) are lit: The battery has approx 50% remaining charge. 1 LED is lit: The battery will be empty soon, please recharge the battery. 6.2 CHARGER INDICATOR Indicator status Explanations and actions Ready for use The charger is connected to the mains and is ready for use;...
- Page 13 2. Turn the protective guard so that uncovered part of the disc is as far apart as possible from the hand on main handle (3). 3. Fix the protection guard by pushing the lock lever inwards (the protective guard should no longer be able to move).
-
Page 14: Cleaning And Maintenance
item. Maximum effect is achieved when the grinder is held at an angle of 15-30° in relation to the item. Move the grinder gently along the item. Give the grinder time to work. It is rarely necessary to press the disc hard against the surface to be worked. -
Page 15: Technical Data
8. TECHNICAL DATA Rated voltage (direct current) 20V d.c. Rotation speed 4000-8500/min Max. disc diameter: Ø 115mm Drive spindle thread: M 14 Battery type Recommendation of battery to use: Model: FBA20U2 or FBA20U4 20V d.c. 2Ah or 4Ah Charger type Recommendation of charger to use: Model: FFC20EU Input 220-240V~ 50/60Hz,0.6A max... -
Page 16: Disposal
BUILDER SAS 32, rue Aristide Bergès - ZI 31270 Cugnaux - France, declares that, Product: Angle Grinder 20V Trademark: Feider Model: FM20V115-A Serial number: 20211004469-20211004968 is in conformity with the essential requirements and other relevant provisions of the applicable European Directives, based on the application of European harmonized standards. -
Page 17: Warranty
13. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identifed as defective by the designated distributor. -
Page 18: Product Failure
14. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 19: Warranty Exclusions
15. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •... - Page 20 BUILDER SAS 32, rue Aristide Bergè s - ZI 31270 Cugnaux - France MADE IN PRC...