Related Manuals for Feider Machines FM2030-1
Summary of Contents for Feider Machines FM2030-1
- Page 1 ORIGINAL INSTRUCTIONS INSTRUCTION MANUAL ANGLE GRINDER FM2030-1 READ THIS INSTRUCTIONS MANUAL BEFORE USE THE TOOL FEIDER 32, rue Aristide Bergès - ZI 31270 Cugnaux - France...
-
Page 2: Table Of Contents
CONTENTS 1. INSTRUCTIONS OF SECURITY 2. SYMBOLS 3. THE PRODUCT 4. USE 5. SERVICNG AND MAINTENANCE 6. DISPOSAL 7. CE DECLARATION 8.WA R R A N T Y 9.PRODUCT FAILURE 10.WARRANTY EXCLUSIONS... -
Page 3: Instructions Of Security
1. INSTRUCTIONS OF SECURITY WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 4 Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
- Page 5 Further safety instructions for all operations Kickback and Related Warnings Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the binding.
-
Page 6: Symbols
Additional safety warnings: a) Check that the maximum speed indicated on the grinding disc corresponds to the maximum speed of the machine. The speed of the machine must not exceed the value on the grinding disc. b) Make sure that the dimensions of the grinding disc correspond to the specifications of the machine. c) Make sure that the grinding disc has been mounted and fastened properly. -
Page 7: The Product
10. Wrench NOTE: the grinding disc is not supplied with this tool. You can buy disc in specialized stores. Ask your retailer for advice. 2) Technical data Model FM2030-1 Voltage 220-240V˜ 50Hz Power 2000W Rated speed in revolution per minute... -
Page 8: Use
Information The declared vibration total value has been measured in accordance with a standard test method and may be used for comparing one tool with another; The declared vibration total value may also be used in a preliminary assessment of exposure. Warning ... - Page 9 Installation of the auxiliary handle The auxiliary handle can be installed in 3 positions: top of the tool and both sides of the tool. The place where to install the auxiliary handle will depend of the position where you will use the tool. Install and screw firmly the handle with the provided wrench until it locks in place.
-
Page 10: Servicng And Maintenance
5.SERVICNG AND MAINTENANCE Keep your tool on a regular basis. This will keep your tool in good working order and extend its lifespan. Do not use abrasive or corrosive agents to clean the tool. These types of products damage your tool. Do not make any repairs by yourself. -
Page 11: Ce Declaration
FEIDER 32, rue Aristide Bergès - ZI 31270 Cugnaux - France Declare that the following tool: ANGLE GRINDER FM2030-1 Serial number: 20210726996-20210727295 20210727296-20210727595 Is in conformity with the requirements of the Directive Machine 2006/42/EC and to the followings Europeans Directives:... -
Page 12: Warranty
8. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 13: Product Failure
9. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 14: Warranty Exclusions
10. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...