Related Manuals for Feider Machines FMDP
Summary of Contents for Feider Machines FMDP
- Page 1 ORIGINAL INSTRUCTIONS Instruction manual Air Die Grinder FMDP WARNING: READ THE FOLLOWING INSTRUCTIONS BEFORE USE THIS TOOL. BUILDER SAS 32, rue Aristide Bergès - ZI 31270 Cugnaux – France MADE IN PRC...
-
Page 2: General Safety Rules
ORIGINAL INSTRUCTIONS 1. General safety rules Read and understand the safety instructions before installing, operating, repairing, maintaining, changing accessories on, or working near the die grinder. Failure to do so can result in serious bodily injury. - Only qualified and trained operators should install, adjust or use the die grinder. - Do not modify this die grinder. - Page 3 ORIGINAL INSTRUCTIONS - Avoid direct contact with the inserted tool during and after use as it can be hot or sharp. - The maximum operating speed of the inserted tool shall equal or exceed the rated speed marked on the tool. - Never mount a grinding wheel, cut-off wheel or router cutter on a die grinder.
-
Page 4: Important Safety Rules
ORIGINAL INSTRUCTIONS - Hold the tool with a light but safe grip, taking account of the required hand reaction forces, because the risk from vibration is generally greater when the grip force is higher. - An improperly mounted or damaged inserted tool can cause excessive vibration levels. Additional safety instructions for pneumatic power tools - Air under pressure can cause severe injury: - always shut off air supply, drain hose of air pressure and disconnect tool from air supply when not in... -
Page 5: Technical Data
ORIGINAL INSTRUCTIONS 3. Technical Data Grinder cap..……………………………………………………………………………………1/4”(6mm) Free speed………………………………………………………………………………………25,000rpm Avg.air consumption……………………………………………………………………………85.5 l/min Operating pressure……………………………………………………………………………...6.3bar Air inlet size……………………………………………………………………………………..1/4” Air hose…………………………………………………………………………………………3/8”ID Weight …………………………………………………………………………………………..0.32kg A weighted sound pressure level…………………………………………………………… 82.8dB(A) Sound power level……………………………………………………………………………93.8 dB(A) Vibration in the handle……………………………………………………………….……….. 0.9m/s 4. Operating Instruction Description .Lever lock throttle for safety. -
Page 6: Loading And Operation
ORIGINAL INSTRUCTIONS through the male fitting in the tool housing. 5. Loading and operation Ensure you read, understand and apply safety instructions before use. Connect the tool to the air hose. Press the trigger to operate the tool. The flow of air may be regulated by adjusting flow valve at the base of the handle. Ensure the air supply is clean and does not exceed 90psi while operating the tool. - Page 7 ORIGINAL INSTRUCTIONS immediately, or serious personal injury could result. Only a qualified persons or an authorized service center can perform repairs or replacement of tool. Disconnect tool from air supply before attempting repair or adjustment. When replacing O-rings or Cylinder, lubricate with air tool oil before assembly.
-
Page 8: Exploding View
ORIGINAL INSTRUCTIONS 8. Exploding view Parts Parts Parts Parts Description Description Description Description Chuck nut Gasket Trigger O-ring Chuck Rotor lining O-ring Noise reduction Front sheath Rotor Screw cap plate Chuck seat Rotor blade Air inlet plug wrench Lock ring Cylinder O-ring wrench... - Page 9 BUILDER SAS ZI, 32 RUE ARISTIDE BERGES – 312070 CUGNAUX – FRANCE Declare that this machine: Die Grinder Model: FMDP Serial number: 20200618669-20200618728 Is in conformity with the directive « machine » 2006/42/CE based on EC type-examination of Name, address and identification number of the notified body: TÜV Rheinland LGA Products GmbH Tillystrasse 2, 90431 Nürnberg, Germany 0197...
-
Page 10: Warranty
11. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 11: Product Failure
12. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 12: Warranty Exclusions
13. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...