Sentera Controls SIG-M-2 Mounting And Operating Instructions
Internet gateway
Hide thumbs
Also See for SIG-M-2:
- User manual (4 pages) ,
- User manual (14 pages) ,
- User manual (14 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Sentera Controls SIG-M-2
Summary of Contents for Sentera Controls SIG-M-2
- Page 1 SIG-M-2 SENTERA INTERNET GATEWAY Mounting and operating instructions...
-
Page 2: Table Of Contents
PRODUCT DESCRIPTION ARTICLE CODES INTENDED AREA OF USE TECHNICAL DATA STANDARDS WIRING AND CONNECTIONS MOUNTING INSTRUCTIONS IN STEPS VERIFICATION OF THE INSTALLATION INSTRUCTIONS TRANSPORT AND STORAGE WARRANTY AND RESTRICTIONS MAINTENANCE MIW-SIG-M-2-EN-000 - 30 / 09 / 2021 2 - 10 www.sentera.eu... -
Page 3: Safety And Precautions
In case there are any questions that are not answered, please contact your technical support or consult a professional. MIW-SIG-M-2-EN-000 - 30 / 09 / 2021 3 - 10 www.sentera.eu... -
Page 4: Product Description
SIG-M-2 Internet Gateway connects a single Sentera device or a network of devices with the Internet in order to configure or monitor them via SenteraWeb. The SIG-M-2 makes wireless or wired connection with the Internet router. The unit has two Modbus RTU channels - a Master channel to communicate with the connected Slave devices and a Slave channel to make the unit accessible for a Master controller or a BMS. -
Page 5: Wiring And Connections
The unit needs to be supplied via one of the RJ45 connectors or via the terminal NO T E block. Do not connect the device via more than one RJ45 connectors and the terminal block simultaneously! MIW-SIG-M-2-EN-000 - 30 / 09 / 2021 5 - 10 www.sentera.eu back to the table of contents... -
Page 6: Mounting Instructions In Steps
The unit needs PoM (24 VDC). So either the Slave or Master channel must be powered with 24 VDC. ATTENTION Do NOT connect both circuits with PoM 24 VDC power supply simultaneously! MIW-SIG-M-2-EN-000 - 30 / 09 / 2021 6 - 10 www.sentera.eu back to the table of contents... - Page 7 Master Slave n Slave 2 NO T E Connect the NBT terminator only in the two most distant units on the network line! MIW-SIG-M-2-EN-000 - 30 / 09 / 2021 7 - 10 www.sentera.eu back to the table of contents...
- Page 8 You should NOT press this button in any other cases! Fig. 5 Wi-Fi reset tact switch 1 - Wi-Fi reset 2 - For button developers only MIW-SIG-M-2-EN-000 - 30 / 09 / 2021 8 - 10 www.sentera.eu back to the table of contents...
-
Page 9: Verification Of The Installation Instructions
In case of heavy pollution, clean with a non-aggressive product. In these circumstances the unit should be disconnected from the supply. Pay attention that no fluids enter the unit. Only reconnect it to the supply when it is completely dry. MIW-SIG-M-2-EN-000 - 30 / 09 / 2021 9 - 10 www.sentera.eu... -
Page 10: Miw-Sig-M-2-En-000 - 30 / 09 / 2021 Www.sentera.eu
SIG-M-2 SENTERA INTERNET GATEWAY MIW-SIG-M-2-EN-000 - 30 / 09 / 2021 10 - 10 www.sentera.eu back to the table of contents...
Need help?
Do you have a question about the SIG-M-2 and is the answer not in the manual?
Questions and answers