Do you have a question about the CLBL530SC and is the answer not in the manual?
Questions and answers
Steve Healy
January 25, 2025
The “bottle cap” attached to the bottle adapter tube is cracked and broken. I need a replacement. No part number seen. What can I do?
1 comments:
Mr. Anderson
February 10, 2025
To obtain a replacement for the cracked "bottle cap" on the BRIO CLBL530SC bottle adapter tube, follow these steps:
1. Contact the vendor and follow their instructions for returning the defective part at your cost. 2. The vendor will inspect the returned part and inform you in writing whether the defect is covered under the Limited Warranty. 3. If the claim is approved, the vendor will replace the defective part at no charge.
Ensure that the issue is not due to misuse, alteration, or improper installation, as such cases are not covered under the warranty.
Safety Information WARNING: To reduce risk of injury and property damage, you must read this entire guide before assembling, installing and operating the dispenser. WARNING: This product dispenses water at very high temperatures. Failure to use properly can cause personal injury.
Intended Use This dispenser is intended to be used in household and similar applications such as: • Staff kitchen areas in shops, offices and other working environments • Farm houses • Hotels, motels and other residential-type environments • Bed-and-breakfast type environments •...
Operational Specifications You must use the dispenser within the following operational parameters to ensure safe, optimal performance. Model No . CLBL530SC Rated Voltage / Frequency 115 V ˜ 60 Hz Heating Power...
Installation 1 . Determine Installation Location IMPORTANT: If the dispenser has been resting on its side for a long period of time, place it in the upright position for approximately 12 hours before installing. Locate the dispenser on a hard and level surface in a cool shaded location near a grounded wall outlet. Position the back of the dispenser no closer than 8 in.
3 . Connect a Water Bottle IMPORTANT: To prevent dry heating, DO NOT turn on the heating and cooling switches until you complete the steps in this procedure. NOTE: The dispenser is compatible with 5-gallon water bottles only. Remove the plastic wrapping and cap from a new 5-gallon bottle of water (purchased separately).
Operation IMPORTANT: This unit has been tested and sanitized prior to packing and shipping. During transit, dust and odors can accumulate in the tank and lines. Dispense and dispose at least one quart of water prior to drinking any water. Turn on Heating and Cooling Switches IMPORTANT: Before you activate the heating and cooling switches, ensure a full bottle of water is installed and...
Change the Water Bottle CAUTION: Do not dispense water if the red change-bottle indicator light is flashing as you could empty the tanks and cause the dispenser to overheat. When the change bottle indicator light on the front of the dispenser flashes red, it is time to replace your empty water bottle with a new water bottle: Open the dispenser cabinet door and slide the empty bottle out of the cabinet.
Clean the Reservoirs The reservoirs should be cleaned every 3 to 4 months to remove mineral buildup and optimize dispenser performance. Gather the following supplies: • 200g (approx. 1.5 cups) citric acid crystals • Hot water • Large bucket or empty 5-gallon bottle •...
Warranty Brio (“Vendor”) warrants to the original purchaser of the Brio Water Coolers (the “Product”), and to no other person, that if the Product is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in the Product shall be free from defects in material and workmanship.
Need help?
Do you have a question about the CLBL530SC and is the answer not in the manual?
Questions and answers
The “bottle cap” attached to the bottle adapter tube is cracked and broken. I need a replacement. No part number seen. What can I do?
To obtain a replacement for the cracked "bottle cap" on the BRIO CLBL530SC bottle adapter tube, follow these steps:
1. Contact the vendor and follow their instructions for returning the defective part at your cost.
2. The vendor will inspect the returned part and inform you in writing whether the defect is covered under the Limited Warranty.
3. If the claim is approved, the vendor will replace the defective part at no charge.
Ensure that the issue is not due to misuse, alteration, or improper installation, as such cases are not covered under the warranty.
This answer is automatically generated