Subscribe to Our Youtube Channel
Related Manuals for Ferno MAX POWER
Summary of Contents for Ferno MAX POWER
- Page 1 Users’ Manual MAX POWER Ferno Slovakia s.r.o. February 2024, ver. 01 913 07 Bosaca 893 Slovakia Pub. No. 50-8409-001_01 Tel: + 421 (0) 32 7708 010, sales.sk@ferno.com...
-
Page 2: Table Of Contents
Contents 1. Disclaimer ..............................4 Technical specification ..........................4 2. Attaching and detaching the MAX Power (track) ……………………………………………………………………………………………………………5 3. Fold & Unfold MAX Power (track) ......................6 4. Adjust handle of the MAX Power ........................7 5. Power System ............................8 5.1. - Page 3 Max Power Ferno Slovakia 6.5.1 Main battery ..........................16 6.5.2 AA batteries ..........................17 6.6 Display: Fault Codes ..........................18 6.6.1 Using a chair with a fault ......................18 7 Additional PowerTraxx Information......................19 7.1 Interconnect Cord ..........................19 7.2 Calibrating the Paddles ........................20 7.2.1...
-
Page 4: Disclaimer
Untrained operators can cause injury or be injured. Permit only trained personnel to operate the PowerTraxx system. Ferno products meet the requirements of Medical Device Directive MDR 2017/745 as established by the European Union. The MAX POWER meets the following standards: •... -
Page 5: Attaching And Detaching The Max Power (Track)
Ferno Slovakia Max Power The MAX Power is compatible with the MAX Chair. 2. Attaching and detaching the MAX Power (track) When using the Max chair with the MAX Power: The chair features an attachable track to aid operators when ascending and descending stairs. -
Page 6: Fold & Unfold Max Power (Track)
Ferno Slovakia Max Power 3. Fold & Unfold MAX Power (track) The track aids in descending stairs. Do not unfold the track if the chair is not needed to descend stairs. To fold the track into the back of the chair, push the lever downwards as shown, until t h e track... -
Page 7: Adjust Handle Of The Max Power
4. Adjust handle of the MAX Power The MAX Power is fitted with an adjustable height handle. To adjust the handle, the operator must pull up on the red cable under the handle. This disengages the handle to slide up or down. When the desired position is reached the operator must release the cable. -
Page 8: Power System
5. Power System WARNING 5.1. PowerTraxx Components DO NOT OPEN MOTOR. No user-serviceable parts inside. Contact Ferno The PowerTraxx consists of the following components: for service ● CONTROL PANEL: The control panel is attached to the lift bar. It allows the operator to control the speed and direction of the belts and monitor the batteries and other aspects of the chair. -
Page 9: Main Battery
Note: The battery and charger instructions from Improper charging can cause injury or damage. Milwaukee supersede those in this manual. For Use only the Ferno-approved battery with the additional information, see the manuals provided chair, and charge only with the Ferno-approved with these components. -
Page 10: Using The Main Battery
Ferno Slovakia Max Power ● Typical charging time is about one hour. Actual charging time varies based on frequency of recharge, depth of discharge, and battery age. If a battery becomes deeply discharged, extend the charging time. ● Patient weight, extreme temperatures, and the combination of using the chair to go up and/or down stairs affect the amount of use available from each battery charge. -
Page 11: Main Battery Shutoff
Ferno Slovakia Max Power 5.2.4 Main Battery shutoff If the internal temperature of the battery becomes too high, the main battery will shut off to protect itself, and all powered chair motion stops. To verify the battery has overheated, press the test button on the battery. -
Page 12: Indicator Lights
Ferno Slovakia Max Power An adapter plug (not supplied) may be needed to adapt the charger plug for the outlet. Typical charging time is about one hour. If the batteries are deeply discharged, extend the charging time. Actual charging time may vary based on frequency of recharge, depth of discharge, and age of batteries. -
Page 13: Paddles
Ferno Slovakia Max Power To use the chair: 1. Press (ON). 2. Tap a paddle up or down to awaken the wireless controller. 3. Allow a few seconds for the wireless connection to be established. When the control panel and motor link, the motor will emit three audible beeps. -
Page 14: Control Panel
Ferno Slovakia Max Power Control Panel 6.1 Control Panel Overview The control-panel components are: ● Brake Button - The symbol on this button is a “Stop Sign” with a slash through it. ● Indicator Light - The light is illuminated red, green, or is not illuminated to provide feedback to the user. -
Page 15: Brake Button
Ferno Slovakia Max Power 6.2 Brake Button The brake prevents the belts from moving unless a paddle is pressed. By default, the brake is engaged when the system has power. To disengage or re-engage the brake, press the brake button on the control panel. -
Page 16: Mode Button
Ferno Slovakia Max Power 6.3 Mode Button The mode button is the Ferno logo Press and hold for four seconds to show the chair status on the display. The display will show the current voltage and amperage used by the power system, plus the revolutions per minute (RPM) of the motor. -
Page 17: Aa Batteries
Ferno Slovakia Max Power 6.5.2 AA batteries Two AA-size batteries power the control panel. If the AA battery warning icon ( ) appears in the upper right corner of the display, replace the AA batteries. Also, if there are no lights on the control panel and the paddles stop functioning, the AA batteries may need to be replaced. -
Page 18: Display: Fault Codes
If a fault occurs, the chair will stop functioning and the display will turn off. In all cases, contact EMSAR or your Ferno distributor for assistance. Control-Panel Fault (E1) – If there is a fault or damage to the control panel (such as a loose or cut wire), a warning triangle symbol and error code “E1”... -
Page 19: Additional Powertraxx Information
Ferno Slovakia Max Power 7. Additional PowerTraxx Information 7.1 Interconnect Cord The interconnect cord physically connects the control panel with the motor. It serves two purposes: ● (Optional) The interconnect cord can be connected permanently to bypass the wireless system. If you decide to use the interconnect cord permanently, arrange the cord so it will not be pinched by opening, closing, or using the chair. -
Page 20: Calibrating The Paddles
7. If you completed all steps properly, the display will show “Calibration OK!” Begin using the chair normally. 7.2.3 If the calibration fails Repeat Steps 1-7. Do not press the paddles until directed to, and press in the proper direction. If the paddles cannot be recalibrated, contact Ferno Technical Support for assistance. -
Page 21: Maintenance
Tel: + 421 (0) 32 7708 010 For service, maintenance and any questions regarding this, e-mail: sales.sk@ferno.com or any other FERNO product, please contact: As our policy is one of continuous Ferno Slovakia s.r.o. development FERNO Slovakia s.r.o. reserves the right to change the specifications without notice.
Need help?
Do you have a question about the MAX POWER and is the answer not in the manual?
Questions and answers