Page 1
LIUMB0B0A_eng-00 Instruction Manual for the use and the maintenance of battery and battery charger Original instructions Part E: MBM06MH rechargeable battery MBC12V battery charger...
Page 3
WHICH THE AUTEC CCS IS INTENDED TO BE INSTALLED, to perform an in-depth and accurate risk assessment to determine if the Autec CCS is suitable for operating a Machine in conditions of safety and operational effectiveness, taking into account the conditions...
Page 4
It is also the responsibility of the Manufacturer and of the design professionals of the Machine on which the Autec CCS is to be installed and used to be certain that the structure, condition, organization and markings of the Machine as installed at the facility is appropriate for and will allow for the safe and reliable use and control of the Machine through the Autec CCS interface.
Page 5
Laws, Regulations and Standards, even local, and that such Users and other Persons do in fact at all times operate or work with the Autec CCS safely and ONLY in compliance with Autec instructions and warnings and with all applicable Laws, Regulations and Standards, even local.
Conformity with standards ................. 12 Contacts and useful addresses ................. 13 Warranty ......................13 Technical assistance and spare parts ..............13 MBM06MH rechargeable battery ................14 Technical data ....................14 Plate ......................... 14 Warnings for use ....................15 First aid ......................16 Instructions for use ...................
(Part A) of the Manual provided with the CCS. Structure of the Instruction Manual The Manual for the use and maintenance of Autec CCSs consists of different parts, that altogether form the Manual; the Manual must be read carefully, understood and applied by the CCS's Owner, User and by all those Persons that, for any reasons, may operate with the CCS or with the Machine where it is installed.
Page 9
Autec CCS and of the Machine, system, device or Machinery system where the CCS is installed. The Manufacturer of the Machine on which the Autec CCS is installed, and the Owner and User of the Machine, must make sure that the Instruction Manual and all of its parts are included in the Instruction Manual of the Machine.
Caption and terminology Contact Autec if any of the instructions, symbols, warnings or images are not clear and understandable. In this part of the Manual, the terms listed below have the same meaning explained in the corresponding paragraph of the general part (Part A):...
Regulation for the storage of instructions are described in the paragraph with the same title in the general part: please refer to that part. Intellectual property Restrictions connected to intellectual property are described in the paragraph with the same title in the general part: please refer to that part. AUTEC LIUMB0B0A_eng-00...
Brief product presentation Battery and battery charger The object of this part of the Manual is the MBM06MH battery, that is meant to be used inside an Autec CCS's Remote station, and the corresponding MBC12V battery charger, that is needed to recharge it.
Contacts and useful addresses The CCSs are produced by Autec Srl – Via Pomaroli, 65 - 36030 Caldogno (VI) - Italy. You can find contacts for Autec, its distributors, dealers and authorized service centres on the website www.autecsafety.com. Warranty General warranty conditions are indicated both in the relevant sheet provided together with this documentation, and in the specific page on the website www.autecsafety.com.
MBM06MH rechargeable battery The MBM06MH rechargeable battery is used to provide power to Autec Remote stations with compatible battery housing (please check this in "Part C" of the Instruction Manual). Contacts Technical data plate Technical data Type Ni-MH Voltage 7.2V...
Do not charge, use or store the battery at temperatures exceeding the limits provided in paragraphs 3.1 and 3.6. The MBM06MH battery cannot be used by People with reduced physical, sensory or mental capabilities, and by children. Do not leave the battery under charge if the charge cycle does not end within the “Max.
The battery must be charged in the "SAFE AREA", i.e. without explosion-risk gases and/or dusts. Autec cannot be held responsible for any use that does not comply with the provisions and directions provided in the Manual, and for any damage that may result from improper, incorrect or irrational use of the battery.
Do not expose the battery to direct sunlight for a long time. Do not store flat batteries for a long time. After long idle periods, it may be needed to carry out several battery discharge/ charge cycles to achieve the best performance. AUTEC LIUMB0B0A_eng-00...
EU Directive 2006/66/EC and its amendments, and with local regulations. MBC12V battery charger The MBC12V battery charger is used to charge the MBM06MH rechargeable battery used in Autec CCSs. Power supply cable...
Technical, identification and approval data of battery charger MBC12V are provided in the plate on the front of the device where the signalling LEDs are. Plates must not be removed from their position: removal immediately voids the warranty. Plates must not be altered or damaged, contact Autec for replacement. AUTEC LIUMB0B0A_eng-00...
The MBC12V battery charger can be powered by a 12/24V battery, with a power supply unit equipped with safety isolating transformer or with the mains adapter provided by Autec. Never use the battery charger and/or the mains adapter if they are damaged.
(max. 4mm/0.16In diameter). It is also possible to fix the power supply cable so that it will not be torn: when fixing the device, place the cable as shown in the figure. 105mm (4.15In) AUTEC LIUMB0B0A_eng-00...
Autec cannot be held responsible for any use that does not comply with the provisions and directions provided in the Manual, and for any damage that may result from improper, incorrect or irrational use of the battery charger and/or of the mains adapter.
NOTE: do not force insertion. The battery slides easily into place and ensures that the positive (+) and negative (-) poles are correctly connected only if it is inserted with the plate facing the compartment, so that the battery's contacts match the battery charger 's contacts. AUTEC LIUMB0B0A_eng-00...
Disposal When disposing of a battery charger, its components must be managed as separate waste. When disposing of a battery charger, please comply with the provisions and/or the regulations in force in the country where it is used. LIUMB0B0A_eng-00 AUTEC...
Then charge the immediately when the battery is battery. inserted in the battery charger. If this problem occurs when a flat battery is inserted, it may be Replace the battery charger. assumed that the battery charger is damaged. AUTEC LIUMB0B0A_eng-00...
Page 26
Replace the battery charger or both, it may be assumed that the the battery. battery charger is damaged; otherwise the damage concerns one of the two batteries. LIUMB0B0A_eng-00 AUTEC...
Page 27
Replace the battery charger or both, it may be assumed that the the battery. battery charger is damaged; otherwise the damage concerns one of the two batteries. AUTEC LIUMB0B0A_eng-00...
Page 28
Via Pomaroli, 65 - 36030 Caldogno (VI) - Italy Tel. +39 0444 901000 - Fax +39 0444 901011 info@autecsafety.com - www.autecsafety.com MADE IN ITALY...
Need help?
Do you have a question about the MBM06MH and is the answer not in the manual?
Questions and answers