Page 1 Fertilizer Spreader Pro-Force Dry Spreader ® Models 1150, 1250, 1350, 1450, 1650, 1850, 2050, 2250 & 2650 Serial Number B39840100 & Higher Part No. 414342...
Page 2: Foreword
— Introduction Pro-Force Dry Spreader Foreword This symbol identifies important safety messages. When you see it, read the message that follows and be alert to the possibility of personal injury. Remember, safety instructions stated in this manual are for your protection. Read them care- fully and follow them closely when working around or using this machine.
Page 3: Product Information
— Introduction Pro-Force Dry Spreader Product Information When ordering parts or when requesting further information or assistance, always give the following information: • Machine name • Model • Serial number All products manufactured by Unverferth Mfg. Co., Inc. are warranted to be free from ma- terial and workmanship defects for one full year from time of consumer delivery.
Page 4: Table Of Contents
— Introduction Pro-Force Dry Spreader Table of Contents Introduction Foreword ..............................2 Product Information ..........................3 Section I Safety General Hazard Information ........................1-2 Safety Decals ............................1-3 Following Safety Instructions ........................1-5 Before Servicing or Operating ....................... 1-6 During Operation ............................ 1-7 Before Transporting..........................
Page 5 — Introduction Pro-Force Dry Spreader Table of Contents Section II Set Up Pre-Delivery Checklist ........................2-2 Fin Assembly Location ........................2-3 Spinner Disc Set Up ......................... 2-4 Dealer Set Up ........................... 2-5 1450 Pull-Type Sideboards and End Caps Installation.............. 2-5 Fenders Installation (Optional) ....................
Page 6 — Introduction Pro-Force Dry Spreader Table of Contents Section III Operation Preparing Dry Spreader ........................3-2 Hardware ............................. 3-2 Hydraulic System ........................3-2 Lubrication ..........................3-2 Transporting ............................3-3 Spreader Start Up Procedure ......................3-4 Spinner Disc Adjustments ......................... 3-5 Spread Test Procedure .......................
Page 7 — Introduction Pro-Force Dry Spreader Table of Contents Section IV Maintenance Lubrication ............................4-2 Chain Tension ............................ 4-6 Gearbox Removal and Oil Change ....................4-8 Dry Spreader Maintenance ........................ 4-9 Seasonal Storage ........................4-9 Purging Hydraulic System ......................4-10 Setting Hydraulic System Flow ....................4-10 Jack Shaft Disassembly and Replacement ..................
Page 8 — Introduction Pro-Force Dry Spreader Table of Contents Section V Parts Please visit www.unverferth.com/parts/ for the most current parts listing. Decals ..................................5-2 Touch-Up Paint ................................5-5 Inverted “V” & Cross Brace Assembly Components ....................5-6 Stainless Steel Box Sideboard Extension Components ...................5-8 Ladder Assembly With Full Float Fenders ......................5-10 Fender, Mudflap &...
Page 9: Section I
— Safety Pro-Force Dry Spreader Section I Safety General Hazard Information ......................1-2 Safety Decals ..........................1-3 Following Safety Instructions ......................1-5 Before Servicing or Operating ......................1-6 During Operation ..........................1-7 Before Transporting ......................... 1-7 During Transport ..........................1-7 Pressurized Oil ..........................
Page 10: General Hazard Information
— Safety Pro-Force Dry Spreader General Hazard Information No accident-prevention program can be successful without the wholehearted cooperation of the person who is directly responsible for the operation of the equipment. A large number of accidents can be prevented only by the operator anticipating the result before the accident is caused and doing something about it.
Page 11: Safety Decals
— Safety Pro-Force Dry Spreader Safety Decals • REPLACE LOST, DAMAGED, PAINTED, OR UNREADABLE DECALS IMMEDIATELY. IF PARTS THAT HAVE DECALS ARE REPLACED, ALSO MAKE SURE TO INSTALL NEW DECALS. THESE DECALS INFORM AND REMIND THE OPERATOR WITH OPERATIONAL INFORMATION AND SAFETY MESSAGES. Part No. Part No. Part No. 95445 9003476 9009170...
Page 12 — Safety Pro-Force Dry Spreader Safety Decals (continued) Part No. 95445 Part No. TA1-906109-0 Part No. PF1234-051 Part No. 9010131 Part No. PF1234-050 Part No. PF1234-052 Part No. TA1-906109-0 Rear Right Hand View Part No. 95445...
Page 13: Following Safety Instructions
— Safety Pro-Force Dry Spreader Following Safety Instructions • Read and understand this operator’s manual before operating. • All machinery should be operated only by trained and authorized personnel. • To prevent machine damage, use only attachments and service parts approved by the manu- facturer.
Page 14: Before Servicing Or Operating
— Safety Pro-Force Dry Spreader Before Servicing or Operating • Avoid working under an implement; however, if it becomes absolutely unavoidable, make sure the implement is safely blocked. • Ensure that all applicable safety decals are installed and legible. • When working around the implement, be careful not to be cut by sharp edges.
Page 15: During Operation
— Safety Pro-Force Dry Spreader During Operation • Comply with all laws and product label directions governing safe product application. • Regulate speed to working conditions. Maintain complete control at all times. • Never service or lubricate equipment when in operation. •...
Page 16: Pressurized Oil
— Safety Pro-Force Dry Spreader Pressurized Oil • Relieve the hydraulic system of all pressure before adjusting or servicing. See chassis operator’s manual for procedure to relieve pressure. • High-pressure fluids can penetrate the skin and cause serious injury or death. Leaks of high-pressure fluids may not be visible.
Page 17: Fertilizer & Chemical Hazards
— Safety Pro-Force Dry Spreader Fertilizer and Chemical Hazards • Always wear personal protective equipment when working with or near fertilizers and/or chemi- cals. This equipment includes, but is not limited to: protective eye wear, gloves, shoes, socks, long-sleeved shirt, and long pants. Additional protection may be required for many types of fertilizers and/or chemicals.
Page 18: Preparing For Emergencies
— Safety Pro-Force Dry Spreader Preparing for Emergencies • Keep a first aid kit and properly rated fire extinguisher nearby. • Keep emergency numbers for fire, rescue, and poison control personnel near the phone. Wearing Protective Equipment • Wear clothing and personal protective equipment appropriate for the job. •...
Page 19: Set Up
— Set Up Pro-Force Dry Spreader Section II Set Up Pre-Delivery Checklist ........................ 2-2 Fin Assembly Location ....................... 2-3 Spinner Disc Set Up ........................2-4 Dealer Set Up ..........................2-5 1450 Pull-Type Sideboards and End Caps Installation ............2-5 Fenders Installation (Optional) ..................... 2-8 Lift Lug Procedure &...
Page 20: Pre-Delivery Checklist
— Set Up Pro-Force Dry Spreader Pre-Delivery Checklist After the cart has been completely assembled, use the following checklist and inspect the cart. Check off each item as it is found satisfactory or after proper adjustment is made. o Check toolbox for controller, if ordered. See “Rate Control Module (RCM) Spreader Set Up”...
Page 21: Fin Assembly Location
— Set Up Pro-Force Dry Spreader Fin Assembly Location NOTE: Left-hand fins rotate clockwise and right-fins rotate counter-clockwise. NOTE: Verify the fin position in both the inner and outer three holes as shown in FIG. 2-1. FIG. 2-1 Fin Position Fin Position Top View...
Page 22: Spinner Disc Set Up
— Set Up Pro-Force Dry Spreader Spinner Disc Set Up • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN WHILE SERVICING IMPLEMENT. • KEEP HANDS CLEAR OF PINCH POINT AREAS. • FALLING OBJECTS CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT WORK UNDER THE MACHINE AT ANY TIME WHILE BEING HOISTED.
Page 23: Dealer Set Up
— Set Up Pro-Force Dry Spreader Dealer Set Up 1450 Pull-Type Sideboards Installation • TO PREVENT PERSONAL INJURY OR DEATH ALWAYS ENSURE THAT THERE ARE PEOPLE WHO REMAIN OUTSIDE THE DRY SPREADER TO ASSIST THE PERSON WORKING INSIDE, AND THAT ALL SAFE WORKPLACE PRACTICES ARE FOLLOWED. THERE IS RESTRICTED MOBILITY AND LIMITED EXIT PATHS WHEN WORKING INSIDE THE IMPLEMENT.
Page 24 — Set Up Pro-Force Dry Spreader Dealer Set Up (continued) 5. Remove and discard right-hand shipping hardware and red shipping brackets. (FIG. 2-4) 6. Lift the right-hand sideboards (416422 - front; 416420 - rear) into position and loosely secure sideboards into place using 3/8” stainless steel capscrews, flat washers and elastic stop nuts along sideboard bottom edge.
Page 25 — Set Up Pro-Force Dry Spreader Dealer Set Up (continued) 9. Lift rear sideboard (PFFES-EXT-1-12) into position and loosely secure with 3/8” stainless steel capscrews, flat washers and elastic stop nuts along inside bottom edge. (FIG. 2-8) 10. Connect rear sideboard to right-hand and left-hand sideboard using two sideboard corner mount plates (416409).
Page 26: Fenders Installation (Optional)
— Set Up Pro-Force Dry Spreader Dealer Set Up Fenders Installation (Optional) • TO PREVENT PERSONAL INJURY OR DEATH ALWAYS ENSURE THAT THERE ARE PEOPLE WHO REMAIN OUTSIDE THE DRY SPREADER TO ASSIST THE PERSON WORKING INSIDE, AND THAT ALL SAFE WORKPLACE PRACTICES ARE FOLLOWED. THERE IS RESTRICTED MOBILITY AND LIMITED EXIT PATHS WHEN WORKING INSIDE THE IMPLEMENT.
Page 27 — Set Up Pro-Force Dry Spreader Dealer Set Up (continued) 2. Attach angle mounting fender (PF50-026) Fig. 2-10 to the left-hand side of the spreader using stainless steel 3/8” hardware. (FIG. 2-10) NOTE: DO NOT tighten hardware at this time. Wait until fenders and mounts are in place before torquing hardware.
Page 28 — Set Up Pro-Force Dry Spreader Dealer Set Up (continued) NOTE: The 1350 unit has only right-hand and left-hand fenders. 1450 to 2250 units have front and rear right-hand and left-hand fenders. 2650 has front, middle and rear right- hand and left-hand fenders. 6.
Page 29: Lift Lug Procedure & Box Mounting Locations
— Set Up Pro-Force Dry Spreader Lift Lug Procedure & Box Mounting Locations • TIPPING OR MOVEMENT OF THE MACHINE CAN CAUSE SERIOUS INJURY OR DEATH. BE SURE MACHINE IS SECURELY BLOCKED. • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN WHILE SERVICING IMPLEMENT.
Page 30 — Set Up Pro-Force Dry Spreader Lift Lug Procedure & Box Mounting Locations (continued) 4. Use a safe lifting device rated at 3,500 lbs. for each corner lift lug. (FIG. 2-18) 5. For undercarriage units, use a safe lifting device rated at 3,500 lbs. for each top hopper corner.
Page 31 — Set Up Pro-Force Dry Spreader Lift Lug Procedure & Box Mounting Locations (continued) 10. Align box mount to the rear notches on side of the box with undercarriage/chassis mount plate slots on each side of the unit as shown. (FIG. 2-20) FIG.
Page 32: Hydraulic Connections Set Up
— Set Up Pro-Force Dry Spreader Hydraulic Connections Set Up • TO PREVENT PERSONAL INJURY OR DEATH ALWAYS ENSURE THAT THERE ARE PEOPLE WHO REMAIN OUTSIDE THE DRY SPREADER TO ASSIST THE PERSON WORK- ING INSIDE, AND THAT ALL SAFE WORKPLACE PRACTICES ARE FOLLOWED. THERE IS RESTRICTED MOBILITY AND LIMITED EXIT PATHS WHEN WORKING INSIDE THE IMPLEMENT.
Page 33 — Set Up Pro-Force Dry Spreader Hydraulic Connections Set Up (continued) 3. At the spreader rear left-hand side, attach FIG. 2-22 hydraulic hose (PF1207-055) to spinner Conveyor Motor Return Line supply hydraulic pipe. (FIG. 2-22) Conveyor Supply Line Spinner Return Spinner Supply Line Line Hose...
Page 34 — Set Up Pro-Force Dry Spreader Hydraulic Connections Set Up (continued) 7. Connect other end of hydraulic hose FIG. 2-26 (PF1207-075) to tee adapter (98200) by left- hand spinner motor. (FIG. 2-26) Tee Adapter Spinner Return Line Hose 8. Attach adapter (9004628) to the top of FIG.
Page 35 — Set Up Pro-Force Dry Spreader Hydraulic Connections Set Up (continued) 10. Attach hydraulic hose (PF1207-03) to FIG. 2-29 conveyor motor return line hydraulic pipe and conveyor motor tee adapter as shown. (FIG. 2-29) Conveyor Motor Return Line Hose 11. At the spreader rear right-hand side, attach FIG.
Page 36 — Set Up Pro-Force Dry Spreader Hydraulic Connections Set Up (continued) 13. Route conveyor return line hydraulic hose FIG. 2-32 behind spinner weldment (PF1236-301) to the left-hand side of the spreader. (FIG. 2-32) Conveyor Return NOTE: Left-hand and right-hand deflector Line Hose weldments (PF1234-108LH and PF1234- 108RH) removed for illustration only.
Page 37 — Set Up Pro-Force Dry Spreader Hydraulic Connections Set Up (continued) 17. Attach hydraulic hose to adapter. (FIG. 2-35) FIG. 2-35 NOTE: For hydraulic hose box length part Hydraulic Hose number, refer to “Spinner & Conveyor Drive Hydraulic Components - For Chassis Mounted Units”...
Page 38: Tarp Installation
— Set Up Pro-Force Dry Spreader Tarp Installation End Caps, Ratchet Straps and Bows Installation • TIPPING OR MOVEMENT OF THE MACHINE CAN CAUSE SERIOUS INJURY OR DEATH. BE SURE MACHINE IS SECURELY BLOCKED. • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN WHILE SERVICING IMPLEMENT.
Page 39 — Set Up Pro-Force Dry Spreader Tarp Installation (continued) 2. Using a safe lifting device rated at 100 lbs., attach end cap (PFF2444) on top of front sideboard using 3/8” stainless steel hardware along inside bottom edge. (FIG. 2-39) Fig. 2-39 Front View End Cap Front...
Page 40 — Set Up Pro-Force Dry Spreader Tarp Installation (continued) 4. Install two ratchet strap assemblies (PFF2608) to left-hand side of hopper using 3/8” stainless steel hardware. (FIG. 2-41) Fig. 2-41 Ratchet Strap Ratchet Strap 5. Install three tarp stop assemblies (9009140) to right-hand side of hopper using 3/8” stainless steel hardware.
Page 41 — Set Up Pro-Force Dry Spreader Tarp Installation (continued) 4. Install short top mount bow extensions (PFF8624) along top of the left-hand sideboards using stainless steel 3/8” hardware. (FIG. 2-43) Fig. 2-43 1850 Unit Shown Left-Hand Sideboards Short Top Mount Bow Extension 5.
Page 42 — Set Up Pro-Force Dry Spreader Tarp Installation (continued) 7. Insert ridge strap through buckle as shown in figure 2-46. 8. Hook ridge strap to top center of end caps and across the top of mount bows as shown in figures 2-45 and 2-46. Strap NOTE: DO NOT tighten strap at this time.
Page 43: Roll Tube And Tarp Installation
— Set Up Pro-Force Dry Spreader Tarp Installation (continued) Fig. 2-49 Roll Tube and Tarp Installation Tarp Stop 14. Using a safe lifting device rated at 250 lbs., lift tarp roll tube onto tarp stops. (FIG. 2-49) 15. Ensure the tarp fixed tube is set 4 5/8” inches from the front of the fixed tube to the front of the hopper.
Page 44 — Set Up Pro-Force Dry Spreader Tarp Installation (continued) NOTE: There are two different ends on the Fig. 2-53 tarp spool cable (PFF5280). Ensure the tarp cables are installed to the front and rear ends of the roll tube as shown in figure 2-53.
Page 45: Hydraulic Oil Cooler Installation (Optional)
— Set Up Pro-Force Dry Spreader Hydraulic Oil Cooler Installation (Optional) • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN WHILE SERVICING IMPLEMENT. • KEEP HANDS CLEAR OF PINCH POINT AREAS. • RELIEVE THE HYDRAULIC SYSTEM OF ALL PRESSURE BEFORE ADJUSTING OR SER- VICING.
Page 46 — Set Up Pro-Force Dry Spreader Hydraulic Oil Cooler Installation (Optional) (continued) 3. Install hydraulic oil cooler (9009177) to the FIG. 2-57 mounting brackets using four 3/8”-16UNC x Cooler 1 1/4” capscrews (900900-056) (SS), eight 3/8” flat washers (900902-038) (SS), four 3/8”...
Page 47 — Set Up Pro-Force Dry Spreader Hydraulic Oil Cooler Installation (Optional) (continued) 7. Route other end of hydraulic hose (PF1207- 0285) as shown to the oil filter. (FIG. 2-60) Hydraulic Hose 8. Attach 90° elbow adapter (PF1202-66) to hydraulic hose and adapter on oil filter. (FIG.
Page 48 — Set Up Pro-Force Dry Spreader Hydraulic Oil Cooler Installation (Optional) (continued) 11. Connect 120°F temperature switch (9009169) FIG. 2-63 to bottom of oil cooler. (FIG. 2-63) 12. Attach other end of temperature switch to the spreader wiring harness as shown. (FIG. 2-63) Temperature Switch...
Page 49: Smv Emblem & Sis Decals
— Set Up Pro-Force Dry Spreader SMV Emblem & SIS Decals • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN WHILE SERVICING IMPLEMENT. • KEEP HANDS CLEAR OF PINCH POINT AREAS. 1. Before the spreader is used, the reflective FIG.
Page 50: Rate Control Module (Rcm) Spreader Set Up
— Set Up Pro-Force Dry Spreader Rate Control Module (RCM) Spreader Set Up When turning on the RCM for the first time, FIG. 2-67 the following steps will have to be performed in order for the RCM to function properly right away.
Page 51 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 5. Under “Application Type”, select “Granular Fertilizer” for product type. The number of products selected correlates with the number of products in figure 2-70. Click next page icon. (FIG. 2-70) NOTE: A quad-force spreader with four products is shown figure 2-70.
Page 52 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 8. Under “Product 3 Granular Application Mode”, select “Granular Full Width”. Click next page icon. (FIG. 2-73) NOTE: If using three products, skip to step 10. FIG. 2-73 9. Under “Product 4 Granular Application Mode”, select “Granular Full Width”.
Page 53 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 10. Ensure “AUX-N Enabled” box is unchecked. Click next page icon. (FIG. 2-75) FIG. 2-75 11. Make sure this box is YES. Click next page icon. (FIG. 2-76) FIG. 2-76 12.
Page 54 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 14. Ensure “Auxiliary Driver 7-12” boxes are selected as “None”. Click next page icon. (FIG. 2-78) FIG. 2-78 15. Ensure “Latched Aux Output 1” box is checked. Click next page icon. (FIG. 2-79) FIG.
Page 55 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 17. If the unit is equipped with a scale and is FIG. 2-81 single bin, select “Product Scale” box. (FIG. 2-81) 18. Ensure only “Product Scale 1” box is checked.
Page 56 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 22. Ensure all the “Pressure Sensor” boxes are selected as “None”. Click next page icon. (FIG. 2-84) FIG. 2-84 23. Ensure “Oil Level Sensor Installed” box is unchecked. Click next page icon. (FIG. 2-85) FIG.
Page 57 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) NOTE: The question mark provides additional information and outlines what happens when adjusting each value setting. 24. Ensure each box is checked for all products. The number of products will correspond to the number of compartments on the spreader.
Page 58 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 30. If valve type is “Fast Close”, set “Valve Response Rate” at 50. This is how fast the valve responds. (FIG. 2-90) 31. Ensure “Control Deadband %” box is 3. 32.
Page 59 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 38. “Tank Capacity” of primary bin depends on whether this is a single or two bin system. Also depends on size of spreader. For testing purposes, entering 15000 is recommended.
Page 60 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) NOTE: The question mark provides additional information and outlines what happens when adjusting each value setting. NOTE: If equipped with a single bin, skip to step 109. 49. “Product 2” is the set up for the Duo- Force conveyor.
Page 61 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 59. “Tank Capacity” of the secondary bin will depend on product density and spreader configuration. For testing purposes, entering 15000 is recommended. (FIG. 2-99) 60. “Current Tank Level” box remains at 0. 61.
Page 62 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) NOTE: The question mark provides additional information and outlines what happens when adjusting each value setting. NOTE: If equipped with Duo-Force only, skip to step 109. 69. “Product 3” is the set up for the Tri-Force conveyor.
Page 63 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 79. “Tank Capacity” of the third bin will depend on product density and spreader configuration. For testing purposes, entering 2100 is recommended. (FIG. 2-105) 80. “Current Tank Level” box remains at 0. 81.
Page 64 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) NOTE: If equipped with Tri-Force only, skip to step 109. 89. “Product 4” is the set up for the Quad- Force conveyor. For “Control Valve Type”, always select “PWM Close” for conveyor. (FIG.
Page 65 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 99. “Tank Capacity” of the fourth bin will depend on product density and spreader configuration. For testing purposes, entering 2100 is recommended. (FIG. 2-111) 100. “Current Tank Level” box remains at 0. 101.
Page 66 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) NOTE: Spinner control is numbered as a product. The number is 1 more than the bin(s) equipped. NOTE: Four products were selected during initial set up. Fifth product is spinner control. 109.
Page 67 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 116. Enter 20 for “Off Rate Alarm” and check FIG. 2-117 “Alarm” box. Click next page icon. (FIG. 2-117) FIG. 2-118 NOTE: “Number of Products” corresponds to bins. 1 for single bin, 2 for Duo-Force, 3 for Tri-Force, and 4 for Quad-Force.
Page 68: Scale Calibration Procedure
— Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) Scale Calibration Procedure 1. Go to the Main Home Screen shown. (FIG. FIG. 2-119 2-119). 2. To set scale calibration, go to Settings page - the 3 gears tab. (FIG. 2-120) 3.
Page 69 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 5. Click “Scale Increment” and set to 20 lbs. (FIG. 2-122) 6. Click the “Scale Calibration” button. (FIG. 2-122) FIG. 2-122 NOTE: If dashes are displayed for “Current Scale Weight”, skip to step 10. If a numerical value is displayed for “Current Scale Weight”, the scale can be calibrated without going to zero.
Page 70 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) NOTE: If dashes are displayed for “Current Scale Weight”, follow steps 11 to 16. (FIG. 2-124) 11. Ensure the spreader is completely empty. 12. Click the “Zero” button to zero the scale. (FIG.
Page 71: Catch Test Calibration Chute Install
— Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) Catch Test Calibration Chute Install • UNEXPECTED SPINNER MOVEMENT CAN CAUSE SERIOUS INJURY OR DEATH. BEFORE PERFORMING CATCH TEST, ENSURE SPINNER CONTROL VALVE IS DISCONNECTED AND EVERYONE IS AWAY FROM MACHINE. •...
Page 72 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) NOTE: Ensure spinner assembly is in the FIG. 2-128 “F” position before starting catch test calibration. (FIG. 2-128 & FIG. 2-129) 5. For the catch test calibration chute Fins (415543R) to fit, spinner dishes (PF1218- 350R and PF1218-350L;...
Page 73: Catch Test Procedure
— Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) Catch Test Procedure 1. Complete “Catch Test Calibration Chute Install” in the previous section before starting catch test procedure. NOTE: If using the spreader scale to determine unloaded weight, record the current scale reading before beginning catch test.
Page 74 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 10. Turn on the “Master Switch”. Click “Start” to begin the catch test. (FIG. 2-133) NOTE: Initial test is to prime the conveyor belt. 11. Cancel the catch test after product begins to collect into the container.
Page 75: Applied Test Procedure
— Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) Applied Test Procedure 1. Ensure pulses/revolution, product density, spreader constant, and gate height values are as shown in figure 2-135. Click “Applied Product calibration”. (FIG. 2-135) FIG. 2-135 2. Click check mark to accept. (FIG. 2-136) FIG.
Page 76: Test Speed Procedure
— Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) Test Speed Procedure Test speed procedure is a test for conveyor function. Entering a test speed value ensures the belt moves. Changing test speed value up or down ensures the belt speeds up or slows down.
Page 77: Tuning Control Valve Response
— Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) Tuning Control Valve Response 1. To change control valve settings, go to Settings (Gear), “System Settings” (Screw- driver/Wrench), and click the “Control Valve Setup” button. (FIG. 2-140) NOTE: For product bins, go to step 2. For spinner control valve, go to step 3.
Page 78: Add Boundary Control Button To Home Page
— Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) Add Boundary Control Button to Home Page 1. Go to the Main Home Screen shown. (FIG. FIG. 2-143 2-143). 2. To add boundary control button, go to Settings page - the 3 gears tab. (FIG. 2-144) 3.
Page 79 — Set Up Pro-Force Dry Spreader RCM Spreader Set Up (continued) 5. After selecting “PR1”, click any gray box labelled “Press To Select” and the box changes to “Selected Readout”. This is where the boundary control button appears on the Main Home Screen. (FIG. 2-146) 6.
Page 80: Single Product Node/Raven 660 Set Up Information
— Set Up Pro-Force Dry Spreader Single Product Node/Raven 660 Set Up Information NOTE: For calibration chute (415552R) install and catch test procedure, refer to SET UP section “RCM Spreader Set Up - Catch Test Calibration Chute Install” and “Catch Test Procedure”. Calibrating the Spread Rate: 1.
Page 81: Rear Feedgate Door Set Up - For Sn B45470100 & Higher
— Set Up Pro-Force Dry Spreader Rear Feedgate Door Set Up - For SN B45470100 & Higher Setting Feedgate Door to 6”–18” High-Range • TIPPING OR MOVEMENT OF THE MACHINE CAN CAUSE SERIOUS INJURY OR DEATH. BE SURE MACHINE IS SECURELY BLOCKED. •...
Page 82 — Set Up Pro-Force Dry Spreader Rear Feedgate Door Set Up (continued) For SN B45470100 & Higher NOTE: Feedgate u-joint and feedgate handle (PF1218-81LTD) are removed in figures 2-155 FIG. 2-155 through 2-159 for illustration only. 4. Support feedgate door with blocking, remove and retain 1/2”...
Page 83 — Set Up Pro-Force Dry Spreader Rear Feedgate Door Set Up (continued) For SN B45470100 & Higher 7. Reattach 3/8” hardware to feedgate jack mount. (FIG. 2-158) FIG. 2-158 3/8” Hardware 8. Reattach feedgate jack to feedgate jack FIG. 2-159 mount using 1/2”...
Page 84 — Set Up Pro-Force Dry Spreader Rear Feedgate Door Set Up (continued) For SN B45470100 & Higher 10. From inside the spreader box, remove and retain middle sets of 1/4” hardware attached to feedgate guide plates (416670). (FIG. 1/4” Hardware 2-161) 11.
Page 85: For Scale, Auto Greaser, And / Or Tarp
— Operation Pro-Force Dry Spreader Section III Operation Preparing Dry Spreader ......................3-2 Hardware ..........................3-2 Hydraulic System ......................... 3-2 Lubrication ........................... 3-2 Transporting ..........................3-3 Spreader Start Up Procedure ....................3-4 Spinner Disc Adjustments ......................3-5 Spread Test Procedure ......................3-5 Spinner Fore/Aft Adjustment ....................
Page 86: Preparing Dry Spreader
— Operation Pro-Force Dry Spreader Preparing Dry Spreader Perform the service checks as outlined below. Repair or replace any damaged or worn parts before operating. Hardware Check for loose bolts and nuts, and tighten as needed. Check again after the first half-day of operation.
Page 87: Transporting
— Operation Pro-Force Dry Spreader Transporting • USE EXCEPTIONAL CARE WHEN OPERATING DRY SPREADER EQUIPPED WITH SINGLE TIRES. THE POSSIBILITY OF TIPPING OVER DURING TURNS OR TRAVEL ON ROUGH ROADS IS INCREASED UNDER THESE CONDITIONS. • DO NOT EXCEED THE GROSS VEHICLE WEIGHT RATING (GVWR). IMPROPER CHASSIS LOADING CAN CAUSE LOSS OF CONTROL OR MACHINE DAMAGE RESULTING IN INJURY OR DEATH.
Page 88: Spreader Start Up Procedure
— Operation Pro-Force Dry Spreader Spreader Start Up Procedure • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN WHILE SERVICING IMPLEMENT. • KEEP HANDS CLEAR OF PINCH POINT AREAS. • RELIEVE HYDRAULIC SYSTEM OF ALL PRESSURE BEFORE ADJUSTING OR SERVICING. SEE CHASSIS OPERATOR’S MANUAL FOR PROPER PROCEDURES.
Page 89: Spinner Disc Adjustments
— Operation Pro-Force Dry Spreader Spinner Disc Adjustments • KEEP HANDS CLEAR OF PINCH POINT AREAS. • ALWAYS WEAR PERSONAL PROTECTIVE EQUIPMENT WHEN WORKING WITH OR NEAR CHEMICALS. THIS EQUIPMENT INCLUDES, BUT IS NOT LIMITED TO: PROTECTIVE EYE WEAR, GLOVES, SHOES, SOCKS, LONG-SLEEVED SHIRT, AND LONG PANTS. ADDITIONAL PROTECTION MAY BE REQUIRED FOR MANY TYPES OF CHEMICALS.
Page 90: Spinner Fore/Aft Adjustment
— Operation Pro-Force Dry Spreader Spinner Disc Adjustments (continued) Spinner Fore/Aft Adjustment 11. After spread test, adjust spinner assembly frontwards or rearwards according to spread pattern test results from the spread test procedure. See Figure 3-1. FIG. 3-1 • Ideal Spread Test Results Flat and taper off towards the outside 5 to 10 ft.
Page 91: Spreading Operation
— Operation Pro-Force Dry Spreader Spreading Operation Lime Spreading • ALWAYS WEAR PERSONAL PROTECTIVE EQUIPMENT WHEN WORKING WITH OR NEAR CHEMICALS. THIS EQUIPMENT INCLUDES, BUT IS NOT LIMITED TO: PROTECTIVE EYE WEAR, GLOVES, SHOES, SOCKS, LONG-SLEEVED SHIRT, AND LONG PANTS. AD- DITIONAL PROTECTION MAY BE REQUIRED FOR MANY TYPES OF CHEMICALS.
Page 92: Fertilizer Spreading
— Operation Pro-Force Dry Spreader Spreading Operation (continued) 4. Open the feedgate to at least 7 inches. NOTE: The four “L” positions can also be use for litter, gypsum and compost. (FIG. 3-3) NOTE: The lower the hole, the farther back FIG.
Page 93 — Operation Pro-Force Dry Spreader Spreading Operation (continued) 6. Adjust spreader constant for the new gate setting. See “RCM Spreader Set Up” in SET UP section. 7. See “Spinner Disc Adjustments” section for spread test, spinner speed setting & spread pattern info.
Page 94: Boundary Control Operation - For Sn B44470100 & Higher
— Operation Pro-Force Dry Spreader Boundary Control Operation - For SN B44470100 & Higher The Pro Force dry spreader is delivered from the factory with a boundary control assembly. The spreader has either Raven RCM components or less-ISOBUS Raven RCM components. This feature is controlled by either the RCM or stand-alone rocker switchbox (9009814).
Page 95: Ladder Operation With Fenders - For Pull-Type Units
— Operation Pro-Force Dry Spreader Ladder Operation With Fenders - For Pull-Type Units • FALLING OR LOWERING EQUIPMENT CAN CAUSE SERIOUS INJURY OR DEATH. KEEP EVERYONE AWAY FROM EQUIPMENT WHEN SUSPENDED, RAISING, OR LOWERING. • DO NOT ALLOW ANYONE TO RIDE ON THE LADDER. MAKE SURE EVERYONE IS CLEAR BEFORE OPERATING MACHINE OR TOWING VEHICLE.
Page 96 — Operation Pro-Force Dry Spreader Ladder Operation With Fenders - For Pull-Type Units (continued) 3. Slowly swing the lower ladder section completely down to working position. (FIG. Fig. 3-8 3-8) Working to Storage Position 1. Slowly lift and swing the lower ladder section up to storage position.
Page 97: Video System (Optional)
— Operation Pro-Force Dry Spreader Video System (Optional) • Do not operate video system below 15°F. Damage to video system can occur. The video system kit includes its own operation instruction sheet. Tarp Operation • TO PREVENT PERSONAL INJURY OR DEATH, DO NOT ALLOW ANYONE ON A CLOSED TARP.
Page 98 — Operation Pro-Force Dry Spreader Tarp Operation (continued) 1. Using both hands, carefully remove the tarp handle weldment from the tube holder. (FIG. 3-10) 2. Roll tarp to the desired location, choosing either a fully open or fully closed position. 3.
Page 99: For Scale, Auto Greaser, And / Or Tarp
— Maintenance Pro-Force Dry Spreader Section IV Maintenance Lubrication ..........................4-2 Chain Tension ..........................4-6 Gearbox Removal and Oil Change .................... 4-8 Dry Spreader Maintenance ......................4-9 Seasonal Storage ......................... 4-9 Purging Hydraulic System ....................4-10 Setting Hydraulic System Flow ..................4-10 Jack Shaft Disassembly and Replacement ................
Page 100: Lubrication
— Maintenance Pro-Force Dry Spreader Lubrication To keep your dry spreader in top operating condition and to assure its proper performance and reliability for a long period of time, periodic inspection and lubrication is a must. Unverferth Mfg. recommends use of NLGI #2 Extreme Pressure grease. The lubrication locations and recommended schedule are as follows:...
Page 101 — Maintenance Pro-Force Dry Spreader Lubrication (continued) (Continued on next page)
Page 102 — Maintenance Pro-Force Dry Spreader Lubrication (continued) ITEM DESCRIPTION POINT LUBRICANT QTY. INTERVAL Hydraulic Oil SAE 15W-40 (For Chassis Check Daily, Tank Capacity Reservoir Tank Units) Change Every 2-3 36 1/2 gal. Hydraulic Oil years (For Pull-Type Units) Check Weekly, Filter See Below Grease Bank For Bearings - Conveyor Drive...
Page 103 — Maintenance Pro-Force Dry Spreader Lubrication (continued) FILLING RESERVOIR TANK (If equipped): 1. Remove cap (PF1220-475). (FIG. 4-2) NOTE: The reservoir tank capacity is 36 1/2 gal. Check hydraulic oil daily and change every 2-3 years. FIG. 4-2 Breather Sight Gauge Filter 2.
Page 104: Chain Tension
— Maintenance Pro-Force Dry Spreader Chain Tension • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN WHILE SERVICING IMPLEMENT. • Straighten or replace bent or distorted crossbars immediately. • Proper chain tension is an essential factor in chain & sprocket life. •...
Page 105 — Maintenance Pro-Force Dry Spreader Chain Tension (continued) 2. If the chain tension indicator decal is not present, not illegible, or is inoperable, use the slots to perform a visual check of the chain tension as shown in figures 4-5 and 4-6. FIG.
Page 106: Gearbox Removal And Oil Change
— Maintenance Pro-Force Dry Spreader Gearbox Removal & Oil Change FIG. 4-7 Breather Socket Head Capscrew Check Plug Drain Plug GEARBOX REMOVAL: 1. Remove check plug (95826). (FIG. 4-7) 2. Using 1/4” allen wrench, remove socket head capscrew (99888-034). (FIG. 4-7) 3.
Page 107: Dry Spreader Maintenance
— Maintenance Pro-Force Dry Spreader Dry Spreader Maintenance • TIPPING OR MOVEMENT OF THE MACHINE CAN CAUSE SERIOUS INJURY OR DEATH. BE SURE MACHINE IS SECURELY BLOCKED. • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN WHILE SERVICING IMPLEMENT. •...
Page 108: Purging Hydraulic System
— Maintenance Pro-Force Dry Spreader Dry Spreader Maintenance (continued) Purging Hydraulic System • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN WHILE SERVICING IMPLEMENT. • RELIEVE HYDRAULIC SYSTEM OF ALL PRESSURE BEFORE ADJUSTING OR SERVICING. SEE CHASSIS OPERATOR’S MANUAL FOR PROPER PROCEDURES. •...
Page 109: Jack Shaft Disassembly And Replacement
— Maintenance Pro-Force Dry Spreader Jack Shaft Disassembly and Replacement NOTE: Replace jack shaft (414860) by removing jack shaft assembly (PF1218-732B) from dry spreader. 1. Remove jack shaft assembly from the spinner assembly weldment and spinner dish. (FIG. 4-8) FIG. 4-8 Spinner Dish Spinner...
Page 110 — Maintenance Pro-Force Dry Spreader Jack Shaft Disassembly and Replacement (continued) 4. Remove and discard jack shaft from jack shaft housing (PF1218-732H). (FIG. 4-10) FIG. 4-10 Jack Shaft Jack Shaft Housing 5. Insert new jack shaft into jack shaft housing. (FIG. 4-10) 6.
Page 111: Adjustable Depth Conveyor Speed Sensor Replacement
— Maintenance Pro-Force Dry Spreader Adjustable Depth Conveyor Speed Sensor Replacement NOTE: The following instructions are for adjustable depth sensors (PF1223-600). For fixed depth sensors (9009645), continue to page 4-15. 1. Park the empty dry spreader on a firm, level surface. Block the machine to keep it from moving.
Page 112 — Maintenance Pro-Force Dry Spreader Adjustable Depth Conveyor Speed Sensor Replacement (continued) FIG. 4-13 • Do not force the sensor against the gear/target tooth, damage may occur. 5. By hand, lightly thread the conveyor speed sensor body into the housing until the sen- sor touches against the motor (gear/target) tooth.
Page 113: Fixed Depth Conveyor Speed Sensor Replacement
— Maintenance Pro-Force Dry Spreader Fixed Depth Conveyor Speed Sensor Replacement NOTE: The following instructions are for fixed depth sensors (9009645). For adjustable depth sensors (PF1223-600), see page 4-13. 1. Park the empty dry spreader on a firm, level surface. Block the machine to keep it from moving.
Page 114: Spinner Motor Speed Sensor Replacement
— Maintenance Pro-Force Dry Spreader Spinner Motor Speed Sensor Replacement 1. Park the empty dry spreader on a firm, level surface. Block the machine to keep it from moving. Set the vehicle’s parking brake, shut off engine, ignition remove key, and disconnect hydraulics from the vehicle and dry spreader.
Page 115 — Maintenance Pro-Force Dry Spreader Spinner Motor Speed Sensor Replacement (continued) • Do not force the sensor against the gear/target tooth, damage may occur. 3. Gently insert the spinner speed sensor body into the sensor hole of the jack shaft assembly until the sensor touches against the motor (gear/target) tooth.
Page 116: Pressure Compensator Cartridge Valve Disassembly
— Maintenance Pro-Force Dry Spreader Pressure Compensator Cartridge Valve Disassembly TOOLS REQUIRED: FIG. 4-22 • Spanner wrench • Vise • 1/4” Allen Wrench • Red Thread Lock • Thread Sealant Position spanner wrench 1. Remove O-ring from cap assembly. (Fig. in this set of holes for Remove 4-22)
Page 117: Hydraulic Servo Valve Manual Override & Timing
— Maintenance Pro-Force Dry Spreader Hydraulic Servo Valve Manual Override & Timing • MOVING CONVEYOR OR ROTATING SPINNER COMPONENTS CAN CAUSE SERIOUS INJURY OR MACHINE DAMAGE. BEFORE OPERATING MANUAL OVERRIDE(S), ENSURE EVERYONE IS AWAY FROM THE DRY SPREADER. • HIGH-PRESSURE FLUIDS CAN PENETRATE THE SKIN AND CAUSE SERIOUS INJURY OR DEATH.
Page 118 — Maintenance Pro-Force Dry Spreader Hydraulic Servo Valve Manual Override & Timing (continued) 5. Run engine at desired RPM and engage FIG. 4-26 hydraulics. 6. Hold the valve motor housing by hand and slowly turn the body clockwise to the deslred flow setting.
Page 119: Hydraulic Pwm Valve Manual Override
— Maintenance Pro-Force Dry Spreader Hydraulic PWM Valve Manual Override For 1350 To 2250 Units With 9009773 PWM Valve • MOVING CONVEYOR OR ROTATING SPINNER COMPONENTS CAN CAUSE SERIOUS INJURY OR MACHINE DAMAGE. BEFORE OPERATING MANUAL OVERRIDE(S), ENSURE EVERYONE IS AWAY FROM THE DRY SPREADER. •...
Page 120: For 1350 To 2250 Units With Pf1211-011A Pwm Valve
— Maintenance Pro-Force Dry Spreader Hydraulic PWM Valve Manual Override For 1350 To 2250 Units With PF1211-011A PWM Valve • MOVING CONVEYOR OR ROTATING SPINNER COMPONENTS CAN CAUSE SERIOUS INJURY OR MACHINE DAMAGE. BEFORE OPERATING MANUAL OVERRIDE(S), ENSURE EVERYONE IS AWAY FROM THE DRY SPREADER. •...
Page 121: For 1150 & 1250 Units
— Maintenance Pro-Force Dry Spreader Hydraulic PWM Valve Manual Override - For 1150 & 1250 Units To Manually Override PWM Valve (9009589): FIG. 4-31 1. Park the empty dry spreader on a firm, level surface. Block the machine to keep it from moving.
Page 122: Chain Shield Seal Strip Replacement
— Maintenance Pro-Force Dry Spreader Chain Shield Seal Strip Replacement • TO PREVENT PERSONAL INJURY OR DEATH, ALWAYS ENSURE THAT THERE ARE PEOPLE WHO REMAIN OUTSIDE THE DRY SPREADER TO ASSIST THE PERSON WORK- ING INSIDE, AND THAT ALL SAFE WORKPLACE PRACTICES ARE FOLLOWED. THERE IS RESTRICTED MOBILITY AND LIMITED EXIT PATHS WHEN WORKING INSIDE THE IMPLEMENT.
Page 123: Bin Level Sensor Assembly
— Maintenance Pro-Force Dry Spreader Bin Level Sensor Replacement • TO PREVENT PERSONAL INJURY OR DEATH, ALWAYS ENSURE THAT THERE ARE PEOPLE WHO REMAIN OUTSIDE THE DRY SPREADER TO ASSIST THE PERSON WORK- ING INSIDE, AND THAT ALL SAFE WORKPLACE PRACTICES ARE FOLLOWED. THERE IS RESTRICTED MOBILITY AND LIMITED EXIT PATHS WHEN WORKING INSIDE THE IMPLEMENT.
Page 124: Spinner And Material Flow Divider Assembly
— Maintenance Pro-Force Dry Spreader Spinner and Material Flow Divider Assembly • TIPPING OR MOVEMENT OF THE MACHINE CAN CAUSE SERIOUS INJURY OR DEATH. BE SURE MACHINE IS SECURELY BLOCKED. • KEEP HANDS CLEAR OF PINCH POINT AREAS. • FALLING OBJECTS CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT WORK UNDER THE MACHINE AT ANY TIME WHILE BEING HOISTED.
Page 125: Rear Feedgate Door Replacement
— Maintenance Pro-Force Dry Spreader Rear Feedgate Door Replacement • TIPPING OR MOVEMENT OF THE MACHINE CAN CAUSE SERIOUS INJURY OR DEATH. BE SURE MACHINE IS SECURELY BLOCKED. • KEEP HANDS CLEAR OF PINCH POINT AREAS. • ALWAYS WEAR PERSONAL PROTECTIVE EQUIPMENT WHEN WORKING WITH OR NEAR CHEMICALS.
Page 126 — Maintenance Pro-Force Dry Spreader Rear Feedgate Door Replacement (continued) 5. Remove and discard the current feedgate door (416608 for SN B45470100 & higher; SN B45470099 & Lower Shown FIG. 4-42 PF1236-350 for SN B45470099 & lower) from the spreader. (FIG. 4-42) Remove Feedgate Door 6.
Page 127 — Maintenance Pro-Force Dry Spreader Rear Feedgate Door Replacement (continued) 9. Slide the new feedgate weldment (416608 for SN B45470100 & higher; PF1236-350 FIG. 4-45 Install New for SN B45470099 & lower) into position Door between the hopper and the guide plates. (FIG.
Page 128: Winterizing
— Maintenance Pro-Force Dry Spreader Winterizing • ALWAYS WEAR PERSONAL PROTECTIVE EQUIPMENT WHEN WORKING WITH OR NEAR FERTILIZERS AND/OR CHEMICALS. THIS EQUIPMENT INCLUDES, BUT IS NOT LIMITED TO: PROTECTIVE EYE WEAR, GLOVES, SHOES, SOCKS, LONG-SLEEVED SHIRT, AND LONG PANTS. ADDITIONAL PROTECTION MAY BE REQUIRED FOR MANY TYPES OF FERTILIZERS AND/OR CHEMICALS.
Page 129: Troubleshooting
— Maintenance Pro-Force Dry Spreader Troubleshooting Problem Possible Cause Corrective Action Incorrect start up sequence Refer to “Spreader Start Up Procedure” section in OPERATION. Verify hydraulic connectors are fully engaged into the SCVs. No hydraulic flow Verify flow is in constant and the pressure side is on the hoses marked “+”.
Page 130 — Maintenance Pro-Force Dry Spreader Troubleshooting (continued) Problem Possible Cause Corrective Action Flow requirement for a combined hydraulic system (2 SCV sets Oil flow too high used) is 46 GPM. Flow requirement for a split hydraulic system (4 SCV sets used) is 76 GPM. Manually override servo valve to verify.
Page 131 — Maintenance Pro-Force Dry Spreader Troubleshooting (continued) Problem Possible Cause Corrective Action Manually override servo valve to verify. Refer to the “Hydraulic Servo Valve Manual Override & Timing” section in MAINTENANCE. If the spinners operate smoothly, issue is in electronics. Verify Control valve settings incorrect valve type and settings are correctly configured.
Page 132: Main Valve Block Assembly - Spinner And Conveyor
— Maintenance Pro-Force Dry Spreader Main Valve Block Assembly - Spinner & Conveyor Conveyor Conveyor Spinner Spinner See “Hydraulic Fittings” and “Hydraulic System Valves & Steel Pipe Adapters” in the MAINTENANCE section for torque specifications. 4-34...
Page 133: Schematics
— Maintenance Pro-Force Dry Spreader Schematics - Spinner & Conveyor Hydraulics 4-35...
Page 134 — Maintenance Pro-Force Dry Spreader Schematic — Split Hydraulics For Undercarriage Mounted Units - SN B45470100 & Higher To “SR” “SR” Hydraulic Pipe RH Side Hydraulic Pipe Hydraulic Pipe To Port “SR” On Valve Block To Port “P” On Valve Block Conveyor Case Drain Hose Supply...
Page 135 — Maintenance Pro-Force Dry Spreader Schematic — Electrical — Troubleshooting Spinner & Conveyor Speed Sensor Wiring Harness NOTE: For operating set up, maintain tie strap color coding between sensors and console harness. Conveyor Spinner Box Cable PF1223-21 9009645 PF1223-22 If console looses rate or spinner speed and the function is moving, the connectors shown on this page can be swapped at the rear of the spreader to troubleshoot the system.
Page 136 — Maintenance Pro-Force Dry Spreader Schematic — Electrical — Chassis Mounted Unit Tail Light Wiring Harness (PF1223-752) 4-38...
Page 137 — Maintenance Pro-Force Dry Spreader Schematic — Product Flow & Rate Harness (9008826) 4-39...
Page 138 — Maintenance Pro-Force Dry Spreader Schematic — RCM Wiring Harness 4-40...
Page 139 — Maintenance Pro-Force Dry Spreader Schematic — Less Raven ISOBUS Rate Control Wiring Harness 4-41...
Page 140 — Maintenance Pro-Force Dry Spreader Schematic — Raven 660 Monitor Rate Control Wiring Harness 4-42...
Page 141: Fertilizer Density Chart
— Maintenance Pro-Force Dry Spreader Fertilizer Density Chart Density Fertilizer (Lbs./Cu.Ft.) Prilled Urea 45-51 Granular Urea 45-51 Prilled Ammonium Nitrate 53-61 Crystalline Ammonium Sulfate 62-69 Ammonium Sulfate 49-65 Diammonium Phosphate 54-66 (DAP) Granular Monoammonium 54-66 Phosphate (MAP) Powdered Monoammonium 53-62 Phosphate (MAP) Granular Triple 59-75...
Page 142: Complete Torque Chart
— Maintenance Pro-Force Dry Spreader Complete Torque Chart Stainless Steel Capscrews - ASTM F593 • Stainless steel hardware has a natural tendency to cold weld/gall when installed/uninstalled at high speeds and/or high torques. It is recommended to apply a thread lubricant approved for stainless steel such as graphite-based anti-seize or molybdenum disulfide based anti-seize when performing an assembly/disassembly of stainless steel hardware.
Page 143 — Maintenance Pro-Force Dry Spreader Complete Torque Chart (continued) Capscrews - Grade 5 NOTE: • Grade 5 capscrews can be identified by three radial dashes on the head. • Capscrews have a yellow or clear appearance. FOOT NEWTON SIZE POUNDS METERS 1/4-20 8-10...
Page 144 — Maintenance Pro-Force Dry Spreader Complete Torque Chart (continued) Capscrews - Grade 5 MagniCoated SAE J429 NOTE: • Grade 5 capscrews can be identified by three radial dashes on the head. • Capscrews have a black appearance. • Capscrews have a K value of 0.15 INCH NEWTON SIZE...
Page 145 — Maintenance Pro-Force Dry Spreader Complete Torque Chart (continued) Capscrews - Grade 8 NOTE: • Grade 8 capscrews can be identified by six radial dashes on the head. • For wheel torque requirements, refer to Wheels and Tires. FOOT NEWTON SIZE POUNDS METERS...
Page 146 — Maintenance Pro-Force Dry Spreader Complete Torque Chart (continued) Capscrews - Grade 8 MagniCoated SAE J429 NOTE: • Grade 8 capscrews can be identified by six radial dashes on the head. • Capscrews have a black appearance. • Capscrews have a K value of 0.15 INCH NEWTON SIZE...
Page 147 — Maintenance Pro-Force Dry Spreader Complete Torque Chart (continued) Torque-Tension Relationship ASTM A307 Grade A, SAE J429 Grade 5 & 8, Holo-Krome Grade 9 Caution: All material included in this chart is advisory only, and its use by anyone is voluntary. In developing this information, Fastenal has made a determined effort to present its contents accurately.
Page 148: Hydraulic Fittings - Torque And Installation
— Maintenance Pro-Force Dry Spreader Hydraulic Fittings – Torque and Installation Tightening O-Ring Fittings 1. Insp ect comp o n e n t s fo r d a ma g e o r Fig. 4-48 O-Ring fittings contamination. Do not connect any other type of fitting to an O-ring fitting.
Page 149 — Maintenance Pro-Force Dry Spreader Hydraulic Fittings – Torque and Installation (continued) Tightening JIC Fittings 1. Inspect all components for damage or Fig. 4-50 contamination. Do not connect any other JIC fittings type of fitting to a JIC fitting. 2. Lubricate the threads with hydraulic oil. 3.
Page 150 — Maintenance Pro-Force Dry Spreader Hydraulic System Valves & Steel Pipe Adapters – Torque Hydraulic System Valves Hydraulic System Valves PART NUMBER TORQUE FT.-LBS. COIL NUT TORQUE PF1211-01 46-54 (Valve - Hyd Servo) PF1211-08 55-60 Hand Tighten (Proportional Valve - 10 NC) 416452 70-75 Hand Tighten...
Page 151 — Parts Pro-Force Dry Spreader Section V Parts Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. Decals................................5-2 Touch-Up Paint ..............................5-5 Inverted “V” & Cross Brace Assembly Components ..................5-6 Stainless Steel Box Sideboard Extension Components..................
Page 152: Decals
— Parts Pro-Force Dry Spreader Decals Please visit www.unverferth.com/parts/ for the most current parts listing. 33 31...
Page 153 DECAL, DANGER “MOVING PART HAZARD 6.25" W X 6" H” 901256 Decal, DANGER "Chemical Exposure" 91605 Decal, FEMA 901607 Decal, UM Oval 95445 Decal, WARNING "High-Pressure Fluid" 9009170 Decal, WARNING “Gross Vehicle Weight” TA1-906109-0 Decal, WARNING “Moving Parts Crush/Cut” 95008 Decal, CAUTION “Slippery Surface”...
Page 154 — Parts Pro-Force Dry Spreader Decals (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. Left-Hand View Right-Hand View Left-Hand View...
Page 155: Touch-Up Paint
— Parts Pro-Force Dry Spreader Decals (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES PF1234-050 DECAL, IMPORTANT “SPINNER DISC LOCATION - 7.5" W” PF1234-051 DECAL, IMPORTANT “FIN LOCATION ON UNIVERSAL DISC” PF1234-052 DECAL, DANGER ‘FLYING MATERIAL - 9.5" W X 7" H” PF1234-054 DECAL, DANGER “MOVING PART HAZARD 6.25"...
Page 156: Inverted "V" & Cross Brace Assembly Components
— Parts Pro-Force Dry Spreader Inverted “V” & Cross Brace Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. 16’ Box Shown To Chassis...
Page 157 — Parts Pro-Force Dry Spreader Inverted “V” & Cross Brace Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. 11’ 12’ 13’ 14’ 16’ 18’ 20’ 22’ 26’ ITEM PART NUMBER DESCRIPTION NOTES Includes PF1234-105ASSY Items 8 - 10 INVERTED VEE ASSEMBLY SS Includes PF1236-105ASSY...
Page 158: Stainless Steel Box Sideboard Extension Components
— Parts Pro-Force Dry Spreader Stainless Steel Box Sideboard Extension Components Please visit www.unverferth.com/parts/ for the most current parts listing. 16’ Box Sideboards Shown Front of Spreader 11’ 12’ 13’ 14’ 16’ 18’ 20’ 22’ 26’ ITEM PART NUMBER DESCRIPTION NOTES 415418 13 3/4”...
Page 159 — Parts Pro-Force Dry Spreader Stainless Steel Box Sideboard Extension Components Please visit www.unverferth.com/parts/ for the most current parts listing. 11’ 12’ 13’ 14’ 16’ 18’ 20’ 22’ 26’ ITEM PART NUMBER DESCRIPTION NOTES 416419 12" High Sideboard, 13’ BOX RH Front SS 416422 12”...
Page 160: Ladder Assembly With Full Float Fenders
— Parts Pro-Force Dry Spreader Ladder Assembly With Full Float Fenders Please visit www.unverferth.com/parts/ for the most current parts listing. NOTE: Refer to Pro-Force Undercarriage manual, 414345, “Ladder Assembly” in PARTS section for additional parts information. 5-10...
Page 161 — Parts Pro-Force Dry Spreader Ladder Assembly With Full Float Fenders Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 414564 Ladder Assembly With Fenders Includes All Items 415891B Ladder Handle Weldment =Black= 900900-056 Capscrew 3/8”-16UNC x 1 1/4” SS 900901-006 Hex Nut 3/8”-16UNC SS 900902-038...
Page 162: Fender, Mudflap & Handrail Components (Optional)
— Parts Pro-Force Dry Spreader Fender, Mudflap & Handrail Components (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. 20’ Box Shown 31 37 5-12...
Page 163 — Parts Pro-Force Dry Spreader Fender, Mudflap & Handrail Components (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. 13’ 14’ 16’ 18’ 20’ 22’ 26’ ITEM PART NUMBER DESCRIPTION NOTES 414432 414408 414431 Also Includes Item 15 414407 STAINLESS STEEL FENDER KIT Pro-Force Handrail Kit 414430...
Page 164 — Parts Pro-Force Dry Spreader Fender, Mud Flap & Handrail Components (Optional) (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. 13’ 14’ 16’ 18’ 20’ 22’ 26’ ITEM PART NUMBER DESCRIPTION NOTES PF1234-613LH Left-Hand Fender SS PF1234-613RH Right-Hand Fender SS 416713 416709 416705...
Page 165: Semi Float Fender Components
— Parts Pro-Force Dry Spreader Semi Float Fender Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES PF1234-712 WELDMENT, SEMI-FLOAT FENDER, RH - SS 12’ PF1234-712LH WELDMENT, SEMI-FLOAT FENDER, LH - SS 12’ PF1234-713 WELDMENT, SEMI-FLOAT FENDER - SS 13' PF1234-714 SEMI-FLOAT FENDER - SS 14'...
Page 166: Hillside Flow Divider
— Parts Pro-Force Dry Spreader Hillside Flow Divider Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES PFHFD-104 BRACKET, HILLSIDE FLOW DIVIDER, RH SS PFHFD-104L BRACKET, HILLSIDE FLOW DIVIDER, LH SS 9007908-051 BOLT, CARRIAGE 3/8"-16UNC X 1" SS 9005640 SERRATED FLANGE NUT, 3/8"-16UNC SS PF1236-453...
Page 167: Lift Lug Components For Chassis Mounted Units
— Parts Pro-Force Dry Spreader Lift Lug Components For Chassis Mounted Units Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 416178R Lift Lug Weldment =Red= 900900-124 Capscrew, 5/8”-11UNC x 2” SS 900902-049 Flat Washer, 5/8” SAE SS 900903-029 LOCK WASHER, 5/8"...
Page 168: Box Window
— Parts Pro-Force Dry Spreader Box Window Please visit www.unverferth.com/parts/ for the most current parts listing. FRONT HOPPER PANEL (REF ONLY) ITEM PART NUMBER DESCRIPTION NOTES 414449 Window Kit Includes Items 1-7 and Instruction Sheet 102608 Window Glass 414446 For 1250 & Larger Units Window Guard Panel 415514 For 1150 Units...
Page 169: Box Mount
— Parts Pro-Force Dry Spreader Box Mount Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 415498 16 FT AG CO MOUNT KIT (SS) 1650 Units-Includes Item 1 415497 14 FT AG CO MOUNT KIT (SS) 1450 Units-Includes Item 1 1850 and 2650 Units 1450 and 2250 Units...
Page 170: Conveyor Mounting Rubber
— Parts Pro-Force Dry Spreader Conveyor Mounting Rubber Please visit www.unverferth.com/parts/ for the most current parts listing. 11’ Box Shown 11’ 12’ 13’ 14’ 16’ 18’ 20’ 22’ 26’ ITEM PART NUMBER DESCRIPTION NOTES PF1000-265 Mounting Rubber - 2 1/2” x 15” PF1000-26 Mounting Rubber - 2 1/2”...
Page 171: Chassis Cover Components
— Parts Pro-Force Dry Spreader Chassis Cover Components Please visit www.unverferth.com/parts/ for the most current parts listing. 14’ Box Bottom View Shown 11’ 12’ 13’ 14’ 16’ 18’ 20’ ITEM PART NUMBER DESCRIPTION NOTES 414960 REAR COVER PANEL 30 3/4 X 70 SS 415116 REAR COVER PANEL 30 3/4 X 70 3/4 SS 414974...
Page 172: Straight Chain Components (Optional)
— Parts Pro-Force Dry Spreader Straight Chain Components (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. NOTE: Refer to “Chain Tension” in MAINTENANCE section for more details. 5-22...
Page 173 — Parts Pro-Force Dry Spreader Straight Chain Components (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. 12’ 13’ 14’ 16’ 18’ 20’ 22’ ITEM PART NUMBER DESCRIPTION NOTES 415593B 22’ #2 CHAIN CONVEYOR IN-LIEU OF BELT OVER CHAIN PF1236-9520S 20’...
Page 174: Belt Over Pintle Chain Components
— Parts Pro-Force Dry Spreader Belt Over Pintle Chain Components Please visit www.unverferth.com/parts/ for the most current parts listing. NOTE: Refer to “Chain Tension” in MAINTENANCE section for more details. 5-24...
Page 175 — Parts Pro-Force Dry Spreader Belt Over Pintle Chain Components Please visit www.unverferth.com/parts/ for the most current parts listing. 12’ 13’ 14’ 16’ 18’ 20’ 22’ 26’ ITEM PART NUMBER DESCRIPTION NOTES 415716 26’ BOX Cleated BOC 34” Wide - Service Kit 415712 22’...
Page 176: Conveyor Idler Components
— Parts Pro-Force Dry Spreader Conveyor Idler Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-26...
Page 177 — Parts Pro-Force Dry Spreader Conveyor Idler Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES PF1217-15 Idler Sprocket PF1217-103 Bearing - Take Up PF50-011 RH Take Up Weldment PF50-011-L LH Take Up Weldment 9399-084 Set Screw 3/8”-16UNC x 3/8”...
Page 178: Chain Tension Indicator Assembly
— Parts Pro-Force Dry Spreader Chain Tension Indicator Assembly Please visit www.unverferth.com/parts/ for the most current parts listing. 5-28...
Page 179 — Parts Pro-Force Dry Spreader Chain Tension Indicator Assembly Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 416057 Chain Tension Indicator Assembly, Left-Hand Includes Items 3-17 416058 Chain Tension Indicator Assembly, Right-Hand 416012 Indicator Link Plate 416013 Indicator Roller 416014...
Page 180: Conveyor Drive Components
— Parts Pro-Force Dry Spreader Conveyor Drive Components Please visit www.unverferth.com/parts/ for the most current parts listing. Dual Conveyor Drive Shown Front View 5-30...
Page 181 — Parts Pro-Force Dry Spreader Conveyor Drive Components Please visit www.unverferth.com/parts/ for the most current parts listing. SINGLE DOUBLE ITEM PART NUMBER DESCRIPTION DRIVE DRIVE NOTES Requires Items: 1-1, 414588 Rear Bearing Slide Weldment SS 1-2, 1-3 9007908-051 Carriage Bolt, 3/8”-16UNC x 1” SS 900903-021 Lock Washer 3/8”...
Page 182: Spinner Assembly Components
— Parts Pro-Force Dry Spreader Spinner Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. NOTE: Refer to “Spinner Motor Speed Sensor Replacement” in MAINTENANCE section for more details. 27 28 Bottom View 5-32...
Page 183 — Parts Pro-Force Dry Spreader Spinner Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES PF1218-002 Spinner Assembly For 2650 to 1350 Chassis Mounted Units Includes Items 1-10, 12-19, 21-26, 28, 30 414882B Spinner Assembly 30”...
Page 184 — Parts Pro-Force Dry Spreader Spinner Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES PF1218-01 Foam Grip PF1218-04 Safety Pin SS 414891 Spinner Adjuster Rod Assembly 9394-009 Hex Nut 1/2”-20UNF G5 414892 Threaded Rod 1/2”Dia.
Page 185: Jack Shaft Assembly Components
— Parts Pro-Force Dry Spreader Jack Shaft Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. NOTE: Refer to “Jack Shaft Disassembly” in MAINTENANCE section for more details. ITEM PART NUMBER DESCRIPTION NOTES PF1218-732B Jack Shaft w/Sensor Mount =Black= Includes Items 2 - 10 PF1204-06 Jack Shaft Oil Seal...
Page 186: Spinner Guards, Flow Divider, & Chunk Deflector Components
— Parts Pro-Force Dry Spreader Spinner Guards, Flow Divider, & Chunk Deflector Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-36...
Page 187 — Parts Pro-Force Dry Spreader Spinner Guards, Flow Divider, & Chunk Deflector Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES PF1236-307 Spinner Guard Upper Weldment Includes Item 13 PF1236-308 Spinner Guard Lower Weldment 900900-056 Capscrew 3/8”-16UNC x 1 1/4”...
Page 188: Feedgate Assembly Components - For Sn B45470100 & Higher
— Parts Pro-Force Dry Spreader Feedgate Assembly Components - For SN B45470100 & Higher Please visit www.unverferth.com/parts/ for the most current parts listing. 5-38...
Page 189 — Parts Pro-Force Dry Spreader Feedgate Assembly Components - For SN B45470100 & Higher Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES PF1218-81LTD FEEDGATE JACK HANDLE, 1/2” RD x 58 1/2” SS 900909-097 ROLL PIN 3/16" Dia. X 1" SS PF1218-85 HEAVY-DUTY FEEDGATE U-JOINT SS PF1218-80...
Page 190: Feedgate Assembly Components - For Sn B45470099 & Lower
— Parts Pro-Force Dry Spreader Feedgate Assembly Components - For SN B45470099 & Lower Please visit www.unverferth.com/parts/ for the most current parts listing. 5-40...
Page 191 — Parts Pro-Force Dry Spreader Feedgate Assembly Components - For SN B45470099 & Lower Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES PF1218-81SS FEEDGATE JACK HANDLE, BAR 1/2” RD x 46” SS 900909-097 ROLL PIN 3/16" Dia. X 1" SS PF1218-85 HEAVY-DUTY FEEDGATE U-JOINT SS PF1218-80...
Page 192: Conveyor, Spinners, Jack Shaft, Feedgate Jack Grease Bank Components
— Parts Pro-Force Dry Spreader Conveyor, Spinners, Jack Shaft, Feedgate Jack Grease Bank Components Please visit www.unverferth.com/parts/ for the most current parts listing. FRONT VIEW BACK VIEW NOTE: For more grease bank details, refer to “Lubrication” in the MAINTENANCE section. 5-42...
Page 193 — Parts Pro-Force Dry Spreader Conveyor, Spinners, Jack Shaft, Feedgate Jack Grease Bank Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 9009894 Grease Hose w/Grease Zerk 1/8” x 44” (1/8” NPT) (SS) Left-Hand Conveyor Drive Bearing Right-Hand Conveyor Drive Bearing 9009899 Grease Hose w/Grease Zerk 1/8”...
Page 194: Chain Shield
— Parts Pro-Force Dry Spreader Chain Shield Please visit www.unverferth.com/parts/ for the most current parts listing. NOTE: Refer to “Chain Shield Seal Strip Replace- ment” in MAINTENANCE Section for More Details. Install Seal Strips With Cords Closest To Belt 5-44...
Page 195 — Parts Pro-Force Dry Spreader Chain Shield Please visit www.unverferth.com/parts/ for the most current parts listing. 11’ 12’ 13’ 14’ 16’ 18’ 20’ 22’ 26’ ITEM PART NUMBER DESCRIPTION NOTES PF1234-912ASSY PF1234-913ASSY PF1234-914ASSY PF1236-916ASSY CHAIN SHIELD ASSEMBLY, RH (Belt Over Chain) PF1234-918ASSY PF1236-920ASSY PF1236-922ASSY...
Page 196 — Parts Pro-Force Dry Spreader Chain Shield (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. 11’ 12’ 13’ 14’ 16’ 18’ 20’ 22’ 26’ ITEM PART NUMBER DESCRIPTION NOTES 414845 Standard Seal Strips, 2 5/8” x 12’ 415347 Standard Seal Strips, 2 5/8”...
Page 197: Front Belt Sealer
— Parts Pro-Force Dry Spreader Front Belt Sealer Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES PF70-053 Front Belt Sealer Strip - For Units w/Belt Over Chain PF70-053-2 Front Belt Sealer Strip - For Units w/Straight Chain PF70-089 Back Plate For Units w/Belt Over Chain PF70-089-1...
Page 198: Gearbox & Hydraulic Motor Assembly
— Parts Pro-Force Dry Spreader Gearbox & Hydraulic Motor Assembly Please visit www.unverferth.com/parts/ for the most current parts listing. Apply high temperature sealant between casting halves. NOTE: Refer to “Gearbox Removal & Oil Change” in MAINTENANCE section for more details. Torque to 19 Ft.-Lbs.
Page 199 — Parts Pro-Force Dry Spreader Gearbox & Hydraulic Motor Assembly Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES Includes Items 1 - 21 PF1220-50MB Left-Hand Gearbox (Black) (Single and Dual Drive) Includes Items 1 - 21 415519B Right-Hand Gearbox (Black) (Dual Drive Only)
Page 200: Main Valve Block Assembly Components Spinner & Conveyor Set Up
— Parts Pro-Force Dry Spreader Main Valve Block Assembly Components Spinner & Conveyor Set Up Please visit www.unverferth.com/parts/ for the most current parts listing. PF1237-02 Valve Assembly Shown 5-50...
Page 201 — Parts Pro-Force Dry Spreader Main Valve Block Assembly Components Spinner & Conveyor Set Up Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES For 2650 Units 416292 Includes Items 1-6 and 13-16 For 1850 & 2250 Units 417005 Pro-Force Valve Assembly Includes Items 1-7 and 13-16...
Page 202: Spinner & Conveyor Drive Hydraulic Components - For Chassis Mounted Units
— Parts Pro-Force Dry Spreader Spinner & Conveyor Drive Hydraulic Components For Chassis Mounted Units Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. Side Side To Chassis For 1350 & Larger Units Preferred Flow Alternate Flow...
Page 203 — Parts Pro-Force Dry Spreader Spinner & Conveyor Drive Hydraulic Components For Chassis Mounted Units Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES PF1207-065 HOSE, HYD. 1" X 103" SAE16 FJ90 & FJ STRAIGHT TAWC15325 ADAPTER, MJIC TO MALE ELBOW 90°...
Page 204: Spinner & Dual Conveyor Drive Hydraulic Components For Chassis Mounted Units
— Parts Pro-Force Dry Spreader Spinner & Dual Conveyor Drive Hydraulic Components For Chassis Mounted Units Please visit www.unverferth.com/parts/ for the most current parts listing. Side To Chassis Side 5-54...
Page 205 — Parts Pro-Force Dry Spreader Spinner & Dual Conveyor Drive Hydraulic Components For Chassis Mounted Units Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES PF1207-04 HOSE, HYD. 1" X 16 1/2" FJ90 & FJ STRAIGHT PF1207-03 HOSE, HYD.
Page 206: Split Hydraulic Components - Sn B45470100 & Higher
— Parts Pro-Force Dry Spreader Split Hydraulic Components - SN B45470100 & Higher For Undercarriage Mounted Units Please visit www.unverferth.com/parts/ for the most current parts listing. RH Side Hydraulic Pipe Conveyor Return Hose Grips To Chassis (-) Orange “SR” Hydraulic Pipe Spinner Supply Hose Grips...
Page 207 — Parts Pro-Force Dry Spreader Split Hydraulic Components - SN B45470100 & Higher For Undercarriage Mounted Units Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES Standard For 1850, 2250, 2650 Units 416862 Pro-Force Split Hydraulics Kit Optional For 1450 Units Includes Items 1-23 and Instruction Sheet...
Page 208: Boundary Control Valve Assembly - Sn B44470100 & Higher
— Parts Pro-Force Dry Spreader Boundary Control Valve Assembly - SN B44470100 & Higher Please visit www.unverferth.com/parts/ for the most current parts listing. NOTE: Refer to “Rate Control Module (RCM) Wiring Harness 12’ Box Right-Hand Components” in this section for additional parts listing. Side Shown NOTE: Refer to “Spinner &...
Page 209: Dump Valve - For Chassis Mounted Units
— Parts Pro-Force Dry Spreader Dump Valve - For Chassis Mounted Units Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES PF1211-176 Dump Valve Assembly Includes Items 1, 2, 3, 4, 5 & 8 97618 Adapter, 1 5/16”-12 MJIC to 1 5/16”-12 O-Ring 98243 ADAPTER, 1 5/16”-12 MO-R TO FJIC SWIVEL...
Page 210: Hydraulic Reservoir / Pump Hydraulic Components For Chassis Mounted Units
— Parts Pro-Force Dry Spreader Hydraulic Reservoir / Pump Hydraulic Components For Chassis Mounted Units Please visit www.unverferth.com/parts/ for the most current parts listing. To Chassis 5-60...
Page 211 9009291 PLUG, PIPE 3/4" SQUARE HEAD SS Includes One Way Valve, O- PF1100-195 ASSY., FILTERHEAD, HYD. Ring, Weld Collar, Mount Bolts, and Gasket PF1220-37 FILTER, OIL, LONG SPIN-ON 901607 UM OVAL DECAL PF1100-195K KIT, SEAL, FILTER HOUSING Not Shown 5-61...
Page 212: In-Line Hydraulic Filter
— Parts Pro-Force Dry Spreader In-Line Hydraulic Filter Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 415337 Hydraulic In-Line Filter Kit Includes All Items 415353 HYDRAULIC FILTER MOUNT (SS) 900900-003 CAPSCREW 1/4”-20UNC X 3/4” 18-8 (SS) 900900-055 CAPSCREW 3/8”-16UNC X 1”...
Page 213: Oil Cooler Components (Optional)
— Parts Pro-Force Dry Spreader Oil Cooler Components (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 415511 Oil Cooler Assembly Kit Includes All Items 9009177 OIL COOLER WITH 12V FAN 900900-056 CAPSCREW, 3/8"-16UNC X 1 1/4" SS 900902-038 FLATWASHER, 3/8"...
Page 214: Hydraulic Pipe Components
— Parts Pro-Force Dry Spreader Hydraulic Pipe Components Please visit www.unverferth.com/parts/ for the most current parts listing. 12’ Box Shown Front of Spreader Port R Return Port SM Spinner Pressure Port CR Conveyor Pressure Port SR Spinner Return 5-64...
Page 215 — Parts Pro-Force Dry Spreader Hydraulic Pipe Components Please visit www.unverferth.com/parts/ for the most current parts listing. 11’ 12’ 13’ 14’ 16’ 18’ 20’ 22’ 26’ ITEM PART NO. DESCRIPTION NOTES All Item 1 PF1234-532 PIPE, HYD., 110 3/16”, 11’ & 12’ BOX For Port SR (Spinner Return) PF1234-533...
Page 216 — Parts Pro-Force Dry Spreader Hydraulic Pipe Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. 11’ 12’ 13’ 14’ 16’ 18’ 20’ 22’ 26’ ITEM PART NO. DESCRIPTION NOTES 414701 Top Plate Hose Clamp 1 3/16” x 2 25/32” SS 900900-010 Capscrew, 1/4”-20UNC x 2 1/4”...
Page 217: Bin Level Sensor Assembly Components
— Parts Pro-Force Dry Spreader Bin Level Sensor Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. Left-Hand Rear View NOTE: Refer to “Bin Level Sensor Replacement” in MAINTENANCE section for more details. ITEM PART NUMBER DESCRIPTION NOTES 9009180 Bin Level Sensor 9008808...
Page 218: Rate Control Module (Rcm) Wiring Harness Components
— Parts Pro-Force Dry Spreader Rate Control Module (RCM) Wiring Harness Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-68...
Page 219 — Parts Pro-Force Dry Spreader Rate Control Module (RCM) Wiring Harness Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 9008826 HARNESS - PRODUCT FLOW AND RATE 1 & 2 BINS 9008095 WIRE HARNESS, RCM ECU 47-PIN RATE 9503387 WIRE HARNESS, 12 FT ADAPTER 9 PIN IBIC 9503390...
Page 220: Less Raven Isobus Rate Control Wiring Harness Components
— Parts Pro-Force Dry Spreader Less Raven ISOBUS Rate Control Wiring Harness Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 9008826 HARNESS - PRODUCT FLOW AND RATE 1 & 2 BINS 9009814 BOUNDARY CONTROL ROCKER SWITCH ASSEMBLY 9009852 EXTENSION HARNESS, 2 PIN WPS TO 2 PIN WPT 9008824...
Page 221: Raven 660 Monitor Rate Control Wiring Harness Components
— Parts Pro-Force Dry Spreader Raven 660 Monitor Rate Control Wiring Harness Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 9008826 HARNESS - PRODUCT FLOW AND RATE 1 & 2 BINS 9007550 Boost Box Harness 9007549 Console Control Harness TA723025...
Page 222: Tail Light Assembly Components Without Fenders
— Parts Pro-Force Dry Spreader Tail Light Assembly Components Without Fenders Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES Includes Items 1 - 11 PF1238-80-522 Tail Light Assembly Without Fenders For 1150, 1250, 1450, 1850, 2250 and 2650 415089 Tail Light - LH Assembly...
Page 223: Tail Light Assembly Components With Fenders
— Parts Pro-Force Dry Spreader Tail Light Assembly Components With Fenders Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES Includes Items 1 - 7 415104 Tail Light Assembly With Fenders For 1350, 1450, 1650, 1850, 2050, 2250, 2650 415105 FENDERS LIGHT MOUNT LH...
Page 224: Transport Lighting Components
— Parts Pro-Force Dry Spreader Transport Lighting Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 414486 Chassis Mounted Lighting Package Includes Items 1 through 6 414552 RH Tail Light Assembly 414553 LH Tail Light Assembly 9002573 Hex Nut - M6 x 1”...
Page 225 — Parts Pro-Force Dry Spreader Notes Please visit www.unverferth.com/parts/ for the most current parts listing. 5-75...
Page 226: Spread Test Components
— Parts Pro-Force Dry Spreader Spread Test Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-76...
Page 227 — Parts Pro-Force Dry Spreader Spread Test Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 414542R Spread Pattern Kit =Red= Includes Items 2 through 14 9008822 Storage Box PF1218-999 Spread Pattern Test Tube PF1218-9990 Spread Pattern Funnel PF1218-9991...
Page 228: Point Scale System Assembly Components
— Parts Pro-Force Dry Spreader Point Scale System Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. 10 10A NOTE: Apply silicone caulk between bolt access cover and mount surface to keep Model UM410 out moisture and fertilizer. Torque to 200 Apply thread Ft.-Lbs.
Page 229 — Parts Pro-Force Dry Spreader Point Scale System Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 16’ & Longer Boxes 414409 6 Point Scale System with 410 Monitor Items 1, 3-10, 15 13’...
Page 230: Less Isobus Rate Control Point Scale System Components
— Parts Pro-Force Dry Spreader Less ISOBUS Rate Control Point Scale System Components Please visit www.unverferth.com/parts/ for the most current parts listing. NOTE: Apply silicone caulk between bolt access cover and mount surface to keep out moisture and fertilizer. Torque to 200 Apply thread Ft.-Lbs.
Page 231 — Parts Pro-Force Dry Spreader Less ISOBUS Rate Control Point Scale System Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 18’, 22’ & 26’ Boxes 416193 6 Point Topcon ISOBUS Scale System Includes Items 1-17 14’...
Page 232: John Deere Chassis Scale System Assembly Components
— Parts Pro-Force Dry Spreader John Deere Chassis Scale System Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. Model UM410 Torque to 200 Ft.-Lbs. NOTE: Position load cell Torque to cable towards the middle 350 Ft.-Lbs. of the box. NOTE: Apply silicone caulk between bolt access cover and mount surface to keep...
Page 233 — Parts Pro-Force Dry Spreader John Deere Chassis Scale System Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 415035 Chassis Mount Scale System with 410 Monitor Items 1, 3-15 415036 Chassis Mount Scale System ISOBUS Items 2-6, 8, 12-15 414586 14’...
Page 234: Cnh Trident Chassis Scale System Assembly Components
— Parts Pro-Force Dry Spreader CNH Trident Chassis Scale System Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. Torque to Model UM410 200 Ft.-Lbs. Torque to 350 Ft.-Lbs. Apply thread locker and torque to 350 Ft.-Lbs. NOTE: Apply silicone caulk NOTE: Position load cell between bolt access cover cable towards the middle...
Page 235 — Parts Pro-Force Dry Spreader CNH Trident Chassis Scale System Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 415035 Chassis Mount Scale System with 410 Monitor Items 1, 3-15 415036 Chassis Mount Scale System ISOBUS Items 2-6, 8, 12-15 414586 14’...
Page 236: Tarp Assembly Components
— Parts Pro-Force Dry Spreader Tarp Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. 12’ Box Shown 5-86...
Page 237 — Parts Pro-Force Dry Spreader Tarp Assembly Components Please visit www.unverferth.com/parts/ for the most current parts listing. 12’ 13’ 14’ 16’ 18’ 20’ 22’ 26’ ITEM PART NO. DESCRIPTION NOTES 9009576 26’ Box - 102” x 25’ Lg. Tarp Kit (SS) PFF96220 22’...
Page 238 — Parts Pro-Force Dry Spreader Tarp Assembly Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. 12’ 13’ 14’ 16’ 18’ 20’ 22’ 26’ ITEM PART NO. DESCRIPTION NOTES 9009554 FACE MOUNT END CAP BRACKET (SS) PFF3809 TELESCOPING CRANK ARM ASSEMBLY W/FLEX JOINT 9009426 TELESCOPING CRANK ARM ASSEMBLY 9009428...
Page 239 — Parts Pro-Force Dry Spreader Notes Please visit www.unverferth.com/parts/ for the most current parts listing. 5-89...
Page 240: Roll Tube, Spring & Spool Assembly
— Parts Pro-Force Dry Spreader Roll Tube, Spring & Spool Assembly Please visit www.unverferth.com/parts/ for the most current parts listing. 5-90...
Page 241 — Parts Pro-Force Dry Spreader Roll Tube, Spring & Spool Assembly Please visit www.unverferth.com/parts/ for the most current parts listing. 12’ 13’ 14’ 16’ 18’ 20’ 22’ 26’ ITEM PART NO. DESCRIPTION NOTES 9009556 9009560 9009273 9009269 Roll Tube, Spring & Spool Assembly Includes all items 9009276 9009243...
Page 242 — Parts Pro-Force Dry Spreader Cab Shield Components (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES PF1234-500 Cab Shield Assembly SS Fits Class 8 Converted Chassis PF1234-501 Cab Shield - Center SS PF1234-502 Cab Shield - RH Side SS PF1234-502L Cab Shield - LH Side SS...
Page 243: Video System (Optional)
— Parts Pro-Force Dry Spreader Video System (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. 9004510 CABLE W/FUSE WIRES Red -- Key Switched Power Black -- Ground Green -- NOT USED White -- NOT USED ITEM PART NO. DESCRIPTION NOTES Includes Items 1 - 8...
Page 244 www.unverferth.com MANUALS\\414342///April 2020-0//August 2020-1//May 2021-2//August 2024-3...

This manual is also suitable for:

Pro-force 1250 Pro-force 1350 Pro-force 1450 Pro-force 1650 Pro-force 1850 Pro-force 2050 ... Show all

um Pro-Force 1150 Manual

Section I

Safety

Set up

Operation

Maintenance

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for um Pro-Force 1150

Summary of Contents for um Pro-Force 1150

This manual is also suitable for:

Table of Contents