Page 1 U n v e r f e r t h ® BULK SEED HANDLING PRODUCT SEED RUNNER UNITS MODELS 2750 & 3750 OPERATOR’S MANUAL PARTS CATALOG Serial Number D53050100 through D55600099 PART NO. 27260...
Page 2: Introduction
INTRODUCTION This symbol identifies important safety Read and study manual completely before at- messages. When you see it, read the tempting to operate this implement. Take this message that follows and be alert to the pos- manual to the field for handy reference when op- sibility of personal injury.
Page 3 THANK YOU FOR YOUR PURCHASE! Please fill out and retain this portion for your records. All products manufactured by Unverferth Manu- facturing Company, Incorporated are warranted to be free from material and workmanship defects for one full year from time of consumer delivery. Your local dealer will gladly assist you with any war- ranty questions.
Page 4: Table Of Contents
ELECTRICAL SCHEMATIC ......2-16 LADDER ..............1-9 SEED TANK LIGHTING TARP..............1-10 ELECTRICAL SCHEMATIC ......2-17 UM 2410 & UM 2510 ELECTRONIC SCALE 1-11 BASIC OPERATION ........1-11 DETAILED PROCEDURE......1-11 DOWNLOADER MODULE (OPT.) .....1-14 OPTIONAL AUTO-SHUTDOWN FEATURE FOR UM 2510 SCALE ONLY ....1-15 OPTIONAL LIGHT KIT ........1-15...
Page 5 FOR 6” CONVEYOR TUBE ......4-14 OPTIONAL SCALE PACKAGE ......3-6 FOR 8” CONVEYOR TUBE ......4-16 OPTIONAL AUTO-SHUTDOWN FEATURE DISCHARGE SPOUT COMPONENTS FOR UM 2510 SCALE ONLY ......3-7 FOR 6” CONVEYOR TUBE ......4-18 OPTIONAL BELT STRETCHER .......3-10 FOR 8” CONVEYOR TUBE ......4-20 OPTIONAL ELECTRONIC ON/OFF VALVE..3-12 HYDRAULIC COMPONENTS ......4-22...
Page 6: General Hazard Information
GENERAL HAzARD INFORMATION No accident-prevention program can be successful without the wholehearted cooperation of the person who is directly responsible for the operation of the equipment. A large number of accidents can be prevented only by the operator anticipating the result before the accident is caused and doing something about it.
Page 7: Safety Decals
SAFETY DECALS Part No. 97961 Part No. 98350 Part No. 95445 Part No. 95839 Part No. 901580 Part No. 97961 Part No. 235161 Part No. 95445 Part No. 97575 Part No. 98229 Part No. TA1-906109-0 Part No. 95445 Part No. 95839 Part No.
Page 8: Follow Safety Instructions
SAFETY FOLLOwING SAFETY INSTRUCTIONS • Read and understand this operator’s manual, and the towing vehicle’s operator’s manual, before operating. • All machinery should be operated only by trained and authorized personnel. • To prevent machine damage, use only attachments and service parts approved by the manufacturer.
Page 9: During Operation
SAFETY DURING OPERATION • Regulate speed to field conditions. Maintain complete control at all times. • Never lubricate equipment when in operation. • Carbon monoxide can cause severe nausea, fainting or death. Do not operate engine in closed or confined area. •...
Page 10: During Transport
SAFETY DURING TRANSPORT • Use good judgment when transporting equipment on highways. Regulate speed to road conditions and maintain complete control. • Maximum speed of implement should never exceed 20 mph. Do not exceed 10 mph during off-highway travel. • Slow down before making sharp turns to avoid tipping.
Page 11: Preparing For Emergencies
SAFETY PREPARING FOR EMERGENCIES • Keep a first aid kit and properly rated fire extinguisher nearby. • Keep emergency numbers for fire, rescue, and poison control personnel near the phone. wEARING PROTECTIVE EqUIPMENT • Wear clothing and personal protective equipment appropriate for the job. •...
Page 12 NOTES (March 2013)
Page 13: Section I - Operations
Operation SECTION I OPERATIONS PREPARING TOWING VEHICLE Before operating implement, refer to towing Estimated weights of the fully loaded Seed vehicle’s operator’s manual for information Runner are: concerning safe methods of operation, hitch Model 3750 capacities, hitch adjustments, tire inﬂ ation, and undercarriage braking operation.
Page 14: Connecting Seed Runner To Towing Vehicle
Operation CONNECTING SEED RUNNER TO TOWING VEHICLE WARNING! DO NOT STAND BETWEEN Connect electrical plug from undercarriage to IMPLEMENT AND TOWING VEHICLE WHEN towing vehicle. Check routing of the electrical HITCHING. cord to be certain it is long enough to pivot when turning, but not too long to touch or rub The Seed Runner Undercarriage is designed to the ground during transport.
Page 15 Operation CAUTION! USE APPROVED ACCES- When transporting on public roads, the conveyor SORY LIGHTS, REFLECTORS, AND DE- needs to be latched in the forward position, VICES WHEN TRANSPORTING AT NIGHT AND extending over the tongue of the undercarriage. DURING PERIODS OF POOR VISIBILITY. Transporting implement with conveyor latched in the rearward position does not comply with WA R N I N G ! A LWAY S T R AV E L AT A...
Page 16: Hydraulic Power Unit Operation
Operation HYDRAULIC POWER UNIT OPERATION WARNING! EXPLOSIVE FUEL CAN CAUSE FIRES AND SEVERE BURNS. STOP EN- GINE BEFORE FILLING FUEL TANK. W A R N I N G ! C A R B O N M O N O X I D E CAN CAUSE SEVERE NAUSEA, FAINTING OR DEATH.
Page 17: Hydraulic Pressure Relief Valve
Operation ADJUSTING HYDRAULIC PRESSURE Mark the location of the set screw in re- RELIEF VALVE lationship to the valve to know where the 1,500 psi setting is, with a paint pen or This unit has an adjustable relief valve permanent marker. which can be adjusted for optimum op- eration.
Page 18: Pivoting Conveyor Side-To-Side
Operation PIVOTING CONVEYOR SIDE-TO-SIDE Conveyor pivot can be left to swing freely, or Remove klik pin from pivot transport lock. Start it can be latched in place at various points engine on hydraulic power unit and increase along the track. throttle speed to wide open.
Page 19: Filling Planter Or Drill
Operation FILLING PLANTER OR DRILL Position the seed tender next to planter so con- NOTE: When using the 8” conveyor to ﬁ ll indi- veyor discharge will be over planter box. Start vidual planter boxes, the cover plate must be engine on hydraulic power unit and increase installed over grate.
Page 20: Filling Seed Tender From Another Wagon Or Bulk Container (Self-Filling)
Operation FILLING SEED TENDER FROM ANOTHER WAGON OR BULK CONTAINER (SELF-FILLING) WARNING! THE SEED RUNNER MUST BE HOOKED TO THE TOWING VEHICLE WHEN BEING FILLED AND THE BRAKES ON THE TOWING VEHICLE MUST BE SET. W A R N I N G ! F I L L T H E F R O N T...
Page 21: Ladder
Operation LADDER Raise ﬂ exible hopper by sliding lever to the upright position. Locate wagon or bulk seed To use ladder, extend lower extension ladder container over conveyor hopper and operate from transport position by sliding bottom rung conveyor to ﬁ ll seed tender box. out until it stops.
Page 22: Tarp
Operation TARP IMPORTANT: Do not release tension from ratch- Do not exert extreme force to roll tarp open or ets once they are set. They should only be closed. If tarp is covered with grain or snow, it released when removing tarp from box. must be removed before operating.
Page 23: Um 2410 & Um 2510 Electronic Scale
Operation UM 2410 & UM 2510 ELECTRONIC SCALE BASIC OPERATION DETAILED PROCEDURES TURN ON THE SCALE: To ensure that the maximum error is within the scale manufacturer's accuracy of +/- 1%, the Press [ON]. Seed Runner must be stationary and on level A brief message is displayed (such as "HELLO").
Page 24: Detailed Procedure
Operation UM 2410 & UM2510 DETAILED PROCEDURE CONTINUED TO SELECT GROSS MODE: TO PRINT: (OPTIONAL FEATURE) GROSS mode displays the weight change since Press the PRINT key. Scale data will be sent the unit was last ZERO/BALANCED. to the printer or data downloader.
Page 25 Operation UM 2410 & UM 2510 DETAILED PROCEDURE CONTINUED TO CHANGE THE SETUP & When the correct SETUP number is displayed, press the [ON] key to advance to the CAL CALIBRATION NUMBERS: Press [ON] to turn on the scale. number.
Page 26: Downloader Module (Opt.)
Operation DOWNLOADER MODULE OPTION GETTING STARTED 3a. DDL Set Up Requirements Use of the DDL (Data Downloader) with Load the DTU (Data Transfer Utilities) software on your PC. Instructions are included with the the EZII series indicators requires the lat- est software version.
Page 27 Operation AUTO-SHUTDOWN FEATURE FOR UM 2510 ONLY - OPTIONAL Turn on the UM2510 Electronic Scale. The scale only allows increments of 10 lbs. Enter the desired amount of product to be dispensed, then press [Enter]. The scale will ﬂ ash “PRESET”. Use either the corded control or the radio remote to turn on the conveyor.
Page 28 Operation NOTES 1-16...
Page 29: Section Ii - Service
Service SECTION II SERVICE LUBRICATION Lubricate with an SAE multi-purpose grease. All ﬁ ttings must be free from dirt and paint to insure entry of lubricant inside bearing. CONVEYOR BEARINGS Lubricate these bearings every 100 hours of operation and at the end of each season be- fore storage.
Page 30: Hydraulic System
Service HYDRAULIC SYSTEM Refer to parts section for hydraulic component Check oil reservoir in hydraulic power detail listing. source and reﬁ ll as needed. Pressurize system again to reverse the mo- When properly assembled and maintained, the tion of step B. Maintain pressure on system hydraulic system of the seed tender requires for at least 5 seconds after cylinder rods little maintenance.
Page 31: Conveyor Belt
Service CONVEYOR BELT Proper belt tension and correct ‘tracking’ of the It is important to move both sides the same belt are critical to maintaining the belt for years distance. Too much tension on the belt will of worry-free use. Belt tension and tracking stretch the splice link and greatly reduce belt should be checked at the beginning of each life.
Page 32 Service Inspect tracking of belt at intake end by opening Adjustment Bolt bottom inspection door on conveyor. Belt should be in the center of the pulley. Conveyor Belt Adjusting Bolts Equal Distance Operate conveyor at slow speed, and tighten or loosen adjustment bolt until belt is running Adjust by loosening (Do Not Remove) the in the center of the pulley.
Page 33: Brake Cleaning And Inspection
Service BRAKE CLEANING AND INSPECTION Your undercarriage brakes must be inspected and serviced immediately if a loss of performance is experienced. With normal use, servicing at one year intervals is usually adequate. With increased usage, this work should be performed more fre- quently as required.
Page 34: How To Measure Voltage
Service HOW TO MEASURE Brake Amps/ Four Magnet Size Magnet Brakes Brakes Brakes Ohms VOLTAGE 7 x 1¼ 10.0 15.0 10 x 1½ 12.0 18.0 System voltage is measured at the magnets by 10 x 2¼ 12.0 18.0 connecting the voltmeter to the two magnet lead 12 x 2 12.0 18.0...
Page 35: Brake Drum Inspection
Service BRAKE DRUM Press a section of the widest end of the bearing into the outer edge of the grease INSPECTION pile closest to the thumb forcing grease into the interior of the bearing. There are two areas of the brake drum that are Repeat this while rotating the bearing from subject to wear and require periodic inspection.
Page 36: Power Pak
Service POWER PAK WARNING! HYDRAULIC SYSTEM MUST BE PURGED OF AIR BEFORE OPERATING For general maintenance and servicing of power TO PREVENT SERIOUS INJURY OR DEATH. pak unit. WARNING! HIGH-PRESSURE FLUIDS NOTE: For maintenace of engine and warranty CAN PENETRATE THE SKIN AND CAUSE information, refer to Operator’s Manual provided SERIOUS INJURY OR DEATH.
Page 37 Service REMOVE INTAKE STRAINER CLEAN & INSPECT APPLY TEFLON TAPE OR PASTE BEFORE REINSTALLING INTO TANK FIG. 2 Using a 1 7/8” wrench, remove intake NOTE: When topping off hydraulic ﬂ uid tank, strainer from tank. Clean strainer of all always use the same ﬂ...
Page 38: Wheel Torque Chart & Tire Specifications
Service WHEEL TORQUE CHART & TIRE SPECIFICATIONS TIRE PRESSURE WHEEL TORQUE REQUIREMENTS The following is to be used as a general guide CAUTION! IMPROPERLY TORQUED for tire inﬂ ation and ﬁ gures can vary depending WHEEL NUTS/BOLTS CAN CAUSE A on speciﬁ...
Page 39: Torque Chart
Service TORQUE CHART HYDRAULIC FITTING-TORQUE AND CAPSCREWS - GRADE 5 INSTALLATION PROCEDURES NOTE: Grade 5 capscrews can be identiﬁ ed by SAE FLARE CONNECTION (J.I.C.) three radial dashes on head. NOTE: Tighten u-bolts evenly and equally to have the same number of threads exposed on each end.
Page 40: Trouble Shooting
Service TROUBLE SHOOTING PROBABLE CAUSE CORRECTION UNDERCARRIAGE SWAYING, TIRE WEAR, LIGHTS Unit sways during travel Check tire pressure Check tongue and steering hardware, tighten ap- propriately Tires show excessive wear Check tire pressure Wheel makes grinding or squeaking noise Service wheel bearings Tail lights are not functioning Check wires and connections Replace lamps...
Page 41 Service TROUBLE SHOOTING CONTINUED PROBABLE CAUSE CORRECTION BELT EDGES SHOWING EXCESSIVE WEAR Belt tracking incorrect Adjust tracking as detailed in “Service” section Poly seals on intake and/or discharge end Replace poly seals worn. PIVOTING ARM WILL NOT RAISE OR LOWER Engine running too slow Increase engine speed Not enough hydraulic ﬂ...
Page 42 Service 2-14...
Page 43 Service 2-15...
Page 44 Service 2-16...
Page 45 Service 2-17...
Page 46 Service NOTES 2-18...
Page 47: Section Iii - Assembly
Assembly SECTION III ASSEMBLY SEED TENDER ASSEMBLY This section contains instructions required for IMPORTANT: The procedures for assembling this assembly of the Seed Tender. unit are intended for two or more people. For your safety, and the safety of others, use For ease of assembly, install all hardware loosely proper tools and equipment and always use safe until assembly is complete and then tighten ac-...
Page 48: Assembling Seed Tender Box To Undercarriage
Assembly ASSEMBLING SEED TENDER BOX TO UNDERCARRIAGE WARNING! SEED TENDER BOX MUST Position the conveyor to the left-hand side of BE SECURELY FASTENED TO UNDERCAR- the undercarriage, then position undercarriage RIAGE AT ALL TIMES. DO NOT FILL BOX OR under box, and lower box onto undercarriage. PIVOT CONVEYOR UNTIL BOX IS SECURED TO Fasten at all four corners using the brackets UNDERCARRIAGE.
Page 49: Ladder Installation
Assembly LADDER INSTALLATION Remove bolt holding extension ladder in and discard. It is used for shipping only. Attach up- Remove upper ladder from the rear of the Seed per ladder to the lower extension ladder using Runner box. Hardware can be discarded. capscrews (9390-058) and locknuts (9928).
Page 50: Assemble Conveyor To Pivot Arm
Assembly ASSEMBLE CONVEYOR TO PIVOT ARM CAUTION! BE SURE HOIST IS SAFETY IMPORTANT: Be sure straps are located inside RATED FOR AT LEAST 500 LBS. FAILURE on/off control rod. TO DO SO WILL CAUSE DAMAGE TO MACHINE AND MAY CAUSE PERSONAL INJURY. Assemble hoses to conveyor motor by threading hoses from end of pivot arm, along conveyor, WA R N I N G ! D O N O T W O R K U N D E R...
Page 51: Hydraulic Diagram
Assembly HYDRAULIC DIAGRAM OPTIONAL HYDRAULICS ELECTRONIC CONTROL VALVE PACKAGE #22660 Refer to “Optional Electronic Control Valve” assembly instructions in this section. STANDARD HYDRAULICS OM25004B...
Page 52: Optional Scale Package
Assembly OPTIONAL SCALE PACKAGE (#24463) ATTACHING WEIGH BARS TO BOX Remove two hold down brackets from one side of the box. Assemble weigh bar (901173) into scale bracket (24809TS) using two 3/8x3 bolts (9390-065) and lock nuts (9928). The weigh bars must be assembled so the ‘TOP’...
Page 53: Optional Auto-Shutdown Feature
Assembly OPTIONAL AUTO-SHUTDOWN FEATURE FOR UM2510 SCALE ONLY ATTACHING WEIGH BARS TO BOX Once the indicator is mounted, attach wiring harness (27938) to the scale monitor. Attach Remove two hold down brackets from one side the shutdown multiswitch (902431) to the wiring of the box.
Page 54 Assembly Units with standard electric shutoff: route Unplug exisiting the wiring harness around the Seed Run- wire harness from ner box, along the hydraulic hoses inside valve on motor spiral wrap and follow up the conveyor to the hydraulic drive motor. Unplug the exisiting wire harness connector from the hydraulic control valve and plug the mating end of wiring harness (27938) into the wir-...
Page 55 Assembly After all wiring harness connections have been made, move the excess wire to a safe location on the Seed Runner frame and secure the entire length of the wiring harness with the included cable ties. Be sure to secure the wiring harness near the engine.
Page 56: Optional Belt Stretcher
Assembly OPTIONAL BELT STRETCHER POSITION TOP BAR WELDMENTS BEHIND CLEATS AS SHOWN THREADED PASS THREADED RODS THRU GUIDE SLEEVE SLEEVES, AND INTO THREADED SLEEVES, BEING SURE TO HAVE THRUST BEARINGS INSTALLED AS SHOWN. GUIDE SLEEVE USE OUTER HOLES FOR 12” BELTS USE INNER HOLES FOR 6”...
Page 57 Assembly STRETCHER ASSEMBLED TO BELT FOR ILLUSTRATION ONLY ASSEMBLE BELT LACING PIN AFTER DRAWING LACINGS TOGETHER BY TURNING THREADED RODS. VIEW A VIEW B VIEW A BELT BOTTOM BARS REST UNDER CONVEYOR SECTION FLANGES CONVEYOR SECTION FLOOR VIEW B STRETCHER ASSEMBLY RIDES ON BOTTOM OF CONVEYOR SECTION FLANGES, AND IS HELD IN LINE BY BOLTS STRETCHER ASSEMBLY CONVEYOR SECTION FLOOR...
Page 58: Optional Electronic On/Off Valve
Assembly OPTIONAL ELECTRONIC ON/OFF VALVE These instructions are for the installation of the CONVEYOR SHOWN Electronic Control for the Unverferth Hydraulic Box Auger and Conveyors. This unit will allow for convenient ON/OFF control of the unit. Standard To install this unit, a 12 Volt D.C. electrical Hydraulic source must be available.
Page 59 Assembly NOTE: To reverse/change the direction of belt Check conveyor for proper installation and movement, remove solenoid block from hydraulic turn on electrical and hydraulic power motor, rotate 180°, and reassemble. To insure supplies. The conveyor will function when the electric ON/OFF switch is working correctly the <ON>...
Page 60 Assembly OPTIONAL 6’-10’ LONG DISCHARGE SPOUT #22578 FOR 6“ CONVEYOR Lower the conveyor to approximately 4-5 Slip the optional telescopic spout with T-bolt feet off the ground. clamp ring (98060) over the conveyor tube end and tighten. Remove the standard spout from the con- OM-01940 veyor.
Page 61: Optional Light Kit
Assembly OPTIONAL LIGHT KIT Park the empty unit on a ﬁ rm, level surface. FIG. 3 Block the wheels on the machine to keep it from moving. Set the towing vehicle’s parking brake, shut-off the engine, and remove the ignition key. FIG.
Page 62 Assembly 9. Connecting wire harness depends on the Model FIG. 6 of your Seed Runner, see below: A. If Seed Runner is equipped with a master key switch, connect wire harness to a power lead from the switch. Wind up extra wire harness, secure with cable tie and lay in the bottom of the pan.
Page 63 Assembly FIG. 11 CONNECT WIRE HARNESS TO BATTERY C. If Seed Runner is an earlier Model (less master key switch or radio remote), use pigtale (21902) included in kit and connect to wire harness. Connect opposite end of pigtale to battery. (NOTE: Ring terminal mounts for battery not included).
Page 64 Assembly NOTES 3-18...
Page 65: Section Iv - Parts
Parts SECTION IV PARTS...
Page 66 Parts BOX DECALS OM04430...
Page 67 901838 Decal, Seed Runner 2750 (4.626 x 35) 901855 Decal, Stripe (4.626 x 28) 901834 Decal, Stripe (4.626 x 18) 901833 Decal, UM Circle 902362 Conspicuity Marking PAINT PART NO. Ivory White - Spray Paint (12oz) 901210 Desert Bisque - Spray Paint (12oz)
Page 68: Ladder Components
Parts LADDER COMPONENTS OM-04435...
Page 69 Parts LADDER COMPONENTS ITEM PART NO. DESCRIPTION 27152TS LADDER WELDMENT =TAN SPECKLE= 26495TS LOWER EXTENSION WELDMENT =TAN SPECKLE= 27153TS LADDER HOLDER =TAN SPECKLE= 901292 CAPPLUG 9390-100 CAPSCREW, 1/2-13UNC x 1 1/4 G5 9405-088 FLAT WASHER 1/2 USS 9800 LOCKNUT, 1/2-13UNC G5 9390-058 CAPSCREW, 3/8-16UNC x 1 3/4 G5 9928...
Page 70: Door, Window, Pivot Components
Parts DOOR, WINDOW, PIVOT COMPONENTS (February 2013) OM04431 Revised 082310-1...
Page 71 Parts DOOR, WINDOW, PIVOT COMPONENTS ITEM PART NO. DESCRIPTION NOTES 102608 WINDOW GLASS (6 x 10) 102693 WEATHERSTRIP 95789 BEARING/SEALED 17MM 901056 WING NUT 1/4-20 UNC 9388-009 CARRIAGE BOLT 1/4-20UNC x 2 1/2 GRADE 5 24251TS DOOR WHEEL WELDMENT =TAN SPECKLE= 22005B GEAR 8 TOOTH MACHINED CASTING 9392-136...
Page 72: Pivot Arm Components
Parts PIVOT ARM COMPONENTS For 6” Tube Conveyor For 8” Tube Conveyor ITEM PART NO. DESCRIPTION NOTES 22018 Bushing 3/8” Dia. 22409B Collar 1” long =Black= 23939TS Pivot Weldment =Tan speckle= 23951 Bushing 1 3/4” Dia. 23970TS Pivot Weldment (for 6” tube) =Tan speckle= 24027TS Angle...
Page 73 Parts PIVOT ARM COMPONENTS ITEM PART NO. DESCRIPTION NOTES 9388-024 Carriage Bolt 5/16-18UNC x 3/4 Grade 5 9394-004 Hex Nut 5/16-18UNC Grade 5 9404-019 Lock Washer 5/16” 26546TS Conveyor Arm Assembly =Tan speckle= 24023TS Handle =Tan speckle= 24028 Bushing 2 1/4” Dia. 24044TS Cam Weldment =Tan speckle=...
Page 74: Hopper Components For 6" Conveyor Tube
Parts HOPPER COMPONENTS FOR 6” TUBE CONVEYOR OM04428 4-10 (February 2013)
Page 75 Parts HOPPER COMPONENTS FOR 6” TUBE CONVEYOR ITEM PART NO. DESCRIPTION NOTES 97420 FLANGE SCREW 1/4-20UNC x 3/4 GRADE 5 97189 HEX NUT/LRG FLG 1/4-20UNC GRADE 5 91256 SCREW/LRG FLG 5/16-18UNC x 3/4 GRADE 5 9390-055 CAPSCREW 3/8-16UNC x 1 GRADE 5 9928 LOCKNUT 3/8-16UNC...
Page 76 Parts HOPPER COMPONENTS FOR 8” TUBE CONVEYOR 4-12 (February 2013)
Page 77 Parts HOPPER COMPONENTS FOR 8” TUBE CONVEYOR ITEM PART NO. DESCRIPTION NOTES 24451TS Clean-Out Door Weldment =Tan Speckle= 24550 Bushing 24620TS Strap 3/4 x 17 1/2 =Tan Speckle= 24986 Poly Strip 2 1/2 x 5 1/2 25258 Seal/Poly Strip 3 1/2 x 20 3/16 25260TS Stand Weldment =Tan Speckle=...
Page 78 Parts IDLER END COMPONENTS FOR 6” TUBE CONVEYOR OM04427 4-14 (February 2013)
Page 79 Parts IDLER END COMPONENTS FOR 6” TUBE CONVEYOR ITEM PART NO. DESCRIPTION NOTES 24050TS CONVEYOR WELDMENT 6 X 18 =TAN SPECKLE= TA1-906109-0 DECAL, WARNING (MOVING PART) 900608 IDLER PULLEY BEARING W/FLANGE (INCLUDES 90° TA0-903088-0 ZERK, SETSCREW & SINGLE LIP SEAL) 93415 GREASE ZERK 90°...
Page 80 Parts IDLER END COMPONENTS FOR 8” TUBE CONVEYOR 4-16 (February 2013)
Page 81 Parts IDLER END COMPONENTS FOR 8” TUBE CONVEYOR ITEM PART NO. DESCRIPTION NOTES 22018 BUSHING TA0-903088-0 BEARING W/FLANGE 1”ID TA0-907104-0 CAPSCREW 3/8-16UNC x 1 3/4 GRADE 5 9500310 COVER =TAN SPECKLE= 23912TS ADJUSTMENT PLATE =TAN SPECKLE= TA2-113926-0 IDLER PULLEY WELDMENT 24451TS CLEAN-OUT DOOR WELDT =TAN SPECKLE=...
Page 82: For 8" Conveyor Tube
Parts DISCHARGE SPOUT COMPONENTS FOR 6” TUBE CONVEYOR OM04426 4-18 Revised 082310-1...
Page 83 Parts DISCHARGE SPOUT COMPONENTS FOR 6” TUBE CONVEYOR ITEM PART NO. DESCRIPTION NOTES 24050TS CONVEYOR WELDMENT 6 x 18 =TAN SPECKLE= 95445 DECAL, WARNING (HIGH-PRESSURE LEAKS) BEARING w/FLANGE TA0-903088-0 (INCLUDES 90° ZERK SET SCREW & SINGLE LIP SEAL) 93415 GREASE ZERK 90° 9388-027 CARRIAGE BOLT 5/16-18UNC x 1 1/2 GRADE 5...
Page 84 Parts DISCHARGE SPOUT COMPONENTS FOR 8” TUBE CONVEYOR OM04539B 4-20...
Page 85 Parts DISCHARGE SPOUT COMPONENTS FOR 8” TUBE CONVEYOR ITEM PART NO. DESCRIPTION NOTES 22018 Bushing 23690 Coupler 23693 Handle 3/8D x 7 3/8 Flat 23735B Cover =BLACK= 23994TS Adjustment Plate =TAN SPECKLE= 24077 Control Rod Assembly 24091TS Bracket =TAN SPECKLE= 24399TS Shield =TAN SPECKLE=...
Page 86: Hydraulic Components
Parts HYDRAULIC COMPONENTS NOTE: Valve is shown ﬂ ipped for clariﬁ cation OM-25004A 4-22 Revised 082310-1...
Page 87 Parts HYDRAULIC COMPONENTS ITEM PART NO. DESCRIPTION NOTES 90° Elbow 3/4-16 JIC Male x 9863 3/4-16 O-Ring Adj Male Boss 90° Elbow 9/16-18 JIC Male x 9874 3/4-16 O-Ring Adj Male Boss 90° Elbow 3/4-16 JIC Male x 93599 7/8-14 O-Ring Adj Male Boss 90°...
Page 88: Power Pak Components
Parts POWER PAK COMPONENTS NOTE: Please use the diagrams to identify which of the two Power Pak units you have before ordering parts. Honda nearest location: USA: www.honda-engines.com phone: 1-800-426-7701 Canada: www.honda.ca phone: 1-888-9HONDA9 OM04543 ITEM DESCRIPTION NOTES 25490IV COVER PLATE =IVORY WHITE= 25495IV BATTERY STRAP 3/4 x 7 5/16...
Page 89 Parts POWER PAK COMPONENTS ITEM DESCRIPTION NOTES 902915 IN-TANK RETURN FILTER 901466 FILTER ELEMENT; NAPA #1552; FRAM P-1654A 901370 JAW COUPLING 5/8” BORE 901371 JAW COUPLER 1” BORE 901372 SPIDER (URETHANE) 902910 SUCTION STRAINER W/MAGNET STRAIGHT 1/2” Hose ID INSERT x 3/4-16UNF 901377 O-Ring BEADED Hose FITTING STRAIGHT 3/4”...
Page 90 Parts POWER PAK COMPONENTS NOTE: Please use the diagrams to identify which of the two Power Pak units you have before ordering parts. Honda nearest location: USA: www.honda-engines.com phone: 1-800-426-7701 Canada: www.honda.ca phone: 1-888-9HONDA9 4-26 (June 2014)
Page 91 Parts POWER PAK COMPONENTS ITEM PART NO. QTY DESCRIPTION ITEM PART NO. QTY DESCRIPTION 25508IV Battery Cover 902915 In-Tank Return Filter 9.2GPM 25515 Pump/Motor Mount Weldment 902123 Cover 25519 Hydraulic Hose 3/4” 902124 Bowl 25673TS Strap 902905 Gasket 26823 Decal, IMPORTANT (Battery) 902906 O-Ring 2 5/16”...
Page 92: Box Electrical Components
Parts BOX ELECTRICAL COMPONENTS OM04438 ITEM DESCRIPTION NOTES 902219 LIGHT/AMBER LED (2 PRONG) 900956 GROMMET OPEN BACK 902218 LIGHT/RED LED (2 PRONG) 901229 CORD GRIP FITTING 24936 WIRE HARNESS TANK 24937 WIRE HARNESS - 11’ 4-28...
Page 93: Master Keyswitch Components
Parts MASTER KEYSWITCH COMPONENTS ITEM DESCRIPTION 27325 Ignition Assembly 9390-055 Capscrew 3/8-16UNC x 1 27143TS Ignition Panel Weldment =Tan Speckle= 27134TS Lever =Tan Speckle= 27157TS Cover =Tan Speckle= 22018 Bushing 9405-064 Flat Washer, 1/4 USS 9936 Locknut, 1/4-20UNC (Grade 5) 9390-003 Capscrew, 1/4-20UNC x 3/4 (Grade 5) 901718...
Page 94: Cable Return Tarp Components
Parts CABLE RETURN TARP SYSTEM COMPONENTS 4-30 (February 2013)
Page 95 Parts CABLE RETURN TARP SYSTEM COMPONENTS ITEM PART NO. DESCRIPTION NOTES 902845 Complete Tarp - Model 2750 902846 Complete Tarp - Model 3750 9003249 Crank Handle w/ Flexible Shaft 901526 Tube Holder Sub Assembly 105825 Nylon Spool/Right - RED 105826 Spring - RED 106042 Ratchet w/ Strap...
Page 96: Undercarriage Hitch Components
Parts UNDERCARRIAGE HITCH COMPONENTS OM04434 ITEM PART NO. DESCRIPTION NOTES 9405-116 FLAT WASHER 1” 98792 CHAIN TRANSPORT 9663 LOCKNUT 1-8UNC JACK STAND WELDMENT 8000# 902326 2 1/2” SQUARE MOUNT 902099 JACK HANDLE & MOUNTING HARDWARE JACK STAND WELDMENT 5000# 24900B 2 1/4”...
Page 97: Undercarriage Frame Components
Parts UNDERCARRIAGE FRAME COMPONENTS OM04432 ITEM PART NO. DESCRIPTION NOTES 98487 GROMMET 1 3/4” DIA. 9801 LOCKNUT 5/8-11UNC 9390-124 CAPSCREW 5/8-11UNCx2 GRADE 5 24897TS TRIPLE AXLE UNDERCARRIAGE WELDMENT =TAN SPECKLE= 25788TS HITCH WELDMENT 10’ UNDERCARRIAGE =TAN SPECKLE= 97575 DECAL, CAUTION (TRANSPORT CHAIN) 97961 DECAL, WARNING (READ &...
Page 98: Undercarriage Fender Components
Parts UNDERCARRIAGE FENDER COMPONENTS OM04433 4-34...
Page 99 Parts UNDERCARRIAGE FENDER COMPONENTS ITEM PART NO. DESCRIPTION NOTES 91070 U-BOLT 5/8-11UNC x 5 (4.25C/C) GRADE 5 9801 LOCKNUT 5/8-11UNC 9390-100 CAPSCREW 1/2-13UNC x 1 1/4 GRADE 5 9405-088 FLAT WASHER 1/2 USS PLT 9800 LOCKNUT 1/2-13UNC 9390-099 CAPSCREW 1/2-13UNC x 1 GRADE 5 9405-100 FLAT WASHER 5/8 USS...
Page 100: Axle & Wheel Components
Parts AXLE & WHEEL COMPONENTS 4-36 Revised 082310-1...
Page 101 Parts AXLE & WHEEL COMPONENTS ITEM PART NO. DESCRIPTION NOTES 901714 Hub 8 Bolt Assembly 901667 Stud Bolt 9/16-18 UNF x 2.82 (Brake Hub) Grade 8 902027 Stud Bolt 9/16-18 UNF x 2.49 (Idler Hub) Grade 8 91812 Bearing Cup 3.265 O.D. (Ref. #25520) 92687 Bearing Cup 2.717 O.D.
Page 102: Undercarriage Electrical Components
Parts UNDERCARRIAGE ELECTRICAL COMPONENTS 24896-WIRING HARNESS 4-38...
Page 103: Electric Breakaway Components
Parts UNDERCARRIAGE ELECTRICAL COMPONENTS ITEM PART NO. DESCRIPTION NOTES 25790TS Light Bar Weldment w/Decals For Service Only Light Bar Weldment =Tan Speckle= 25045 Wiring Harness - 165” Front 25046 Wiring Harness - 338” Rear Electric Breakaway Kit See Below 902219 Light/Amber LED (2 Prong) 902218 Light/Red LED (2 Prong)
Page 104 Parts ELECTRONIC ON/OFF CONTROL COMPONENTS ITEM PART NO. DESCRIPTION QTY. 26512 Electric On/Off Control Kit 26330 Switch Assembly 26341 Wire Harness 26505 Plate 26513 Instruction Sheet 9000106 Cable Tie, 6" 900636 Reducer 901878 Electric Valve 91306 O-Ring Capscrew, 9390-037 5/16-18UNC x 2 3/4 94038 Cable Tie, 32"...
Page 105 Parts OPTIONAL SCALE COMPONENTS OM04436 ITEM PART NO. DESCRIPTION NOTES 25063TS SCALE ENCLOSURE WITH INDICATOR =TAN SPECKLE= 24508TS SCALE ENCLOSURE WELDMENT =TAN SPECKLE= 25061TS SCALE COVER =TAN SPECKLE= 22018 BUSHING FOR VALVE HANDLE 9405-064 FLAT WASHER 1/4 USS 9390-003 CAPSCREW 1/4-20UNCx3/4 GRADE 5 9936 LOCKNUT 1/4-20UNC...
Page 106 Parts OPTIONAL CONVEYOR SPOUT LIGHT KIT ITEM PART NO. DESCRIPTION 26787 Optional Light Kit 21902 2-Way Connector 26789 Light Assembly 26791B Light Mount Bracket 26792 Instruction Sheet 9000106 Cable Tie, 6” Long 902155 Wire Harness, 2-Way 420’ Long 4-42...
Page 107 Parts OPTIONAL AUTO-SHUT OFF KIT ITEM PART NO. DESCRIPTION NOTES 27707 Optional Auto-Shut Off Kit (UM2510) Includes Items 2 through 28 2000321TS Optional Auto-Shut Off Kit (UM2520) Includes Items 2 through 28 901173 Scale Weigh Bar, 2.125 Dia. 9928 Locknut, 3/8-16UNC Grade 5 9801 Locknut, 5/8-11UNC...
Page 108 Parts OPTIONAL GOOSE NECK HITCH COMPONENTS Front View Rear View 4-44 (February 2013)
Page 109 Parts OPTIONAL GOOSE NECK HITCH COMPONENTS ITEM PART NO. DESCRIPTION NOTES 27407TS Goose Neck Hitch Assembly w/Square Neck Includes Items 1-24 2000128 Goose Neck Hitch Assembly W/Rounded Neck NOT SHOWN 107905B Jack Weldment 25003 Conspicuity Marking / Reﬂ ectors Break Away Switch & Battery w/Charger & Refer to “Electric Breakaway ---- Components”...
Page 110 Parts OPTIONAL SCALE PLATFORM FOR UNITS LESS UNDERCARRIAGE ITEM PART NO. DESCRIPTION NOTES Optional Scale Platform for Units Less 25898TS Includes Items 1-5 Undercarriage 25746TS Scale Base 9390-065 Capscrew 3/8-16UNC x 3 1/2 9390-124 Capscrew 5/8-11UNC x 2 9801 Locknut 5/8-11UNC 9928 Locknut 3/8-16UNC 4-46...
Page 111 Parts NOTES 4-47 (February 2013)
Page 112 www.unverferth.com L:\MANUALS\SEEDTENDER\27260.INDD\\\MARCH 2013-3\\JUNE 2014-4//MARCH 2015-4...

This manual is also suitable for:

Unverferth 3750

um Unverferth 2750 Operator's Manual And Parts Catalog

Section I - Operations

Section II - Service

Section III - Assembly

Section IV - Parts

Quick Links

Troubleshooting

Summary of Contents for um Unverferth 2750

This manual is also suitable for:

Table of Contents