Subscribe to Our Youtube Channel
Related Manuals for Amphenol RFS Technologies KD-C70 Series
Summary of Contents for Amphenol RFS Technologies KD-C70 Series
- Page 1 Doc #: 10000036988 Ver A Document No.: 10000036988 Quick Installation Guide DESICCANT AIR DEHYDRATOR KD-C70 Serie Model Covered by This Manual: KD-C70/KD-C72/KD-C74-DC PLEASE READ THIS MANUAL THOROUGHLY AND SAVE FOR FUTURE REFERENCE.
- Page 2 Doc #: 10000036988 Ver A In additional to this Quick Installation Guide, a complete product manual is available for access by scanning this QR code: Or by visiting this link: https://www.rfstechnologies.com/images/pressurization_products/kd-c70_manual_10000036987.pdf TABLE OF CONTENTS WARNINGS, CAUTIONS & NOTES ......................1 2.
- Page 3 Doc #: 10000036988 Ver A 1. WARNINGS, CAUTIONS & NOTES NOTE: Read this manual before installation or operation of the dehydrator. _________________________________________________________________________________________________________ W A R N I N G Power source of the dehydrator must have proper ground connection, to reduces the risk of electrical shock, electrocution, and fires caused by unexpected voltage spikes or short circuits.
- Page 4 Doc #: 10000036988 Ver A 2. PRODUCT INTRODUCTION 2.1 Product Description The KD-C70 series Air Dehydrator is designed to provide a source of dry, pressurized air by removing moisture from the ambient air. The unit automates the process by employing high- performance allochroic silica gel as a desiccant.
- Page 5 Doc #: 10000036988 Ver A 2.4 Appearance and Interface 1. Desiccant display window 2. Digital display 3. Control buttons 4. Ambient temperature and humidity display 5. Indicator lights 6. RJ45 port 7. Gas Outlets 8. Alarm port 9. Power socket 10.
- Page 6 Doc #: 10000036988 Ver A KD-C70 Series Part Number Power cord x 1 piece, 6ft (1.8m) length AC: KD25002 DC: KD25004 Fuse x 2 pieces See table below Nozzle connector x 4 pieces, G 1/8 to 3/8” tube KD26001 Teflon tape x 1 roll KD29001 PU tube x 33ft (10m) length KD24009...
- Page 7 Doc #: 10000036988 Ver A 3.4 Installation Mode of KD-C70 Series The Dehydrator is designed for desktop, and wall mounting. Please select an appropriate installation model based on the actual site conditions. 3.4.1 Desktop Installation Place the dehydrator on a solid, level surface. Allow at least 2" clearance at the top for proper heat dissipation.
- Page 8 Doc #: 10000036988 Ver A Switch the power to the ON position to turn on the dehydrator. When the dehydrator is operating, the digital display window on the front panel will show "P XX” where "XX" represents the current system pressure value. The dehydrator is pre-programmed with the following configurations as shown in the table below.
- Page 9 Doc #: 10000036988 Ver A 3.6.4 Save Settings At the Alarm Buzzer setting interface, press "Set" again to save and apply the new configurations to the dryer. The display will then return to the "P XX" interface. Configuration is not lost or changed when the dehydrator is turned off. 3.7 Connect the Dehydrator to the Tubing and the System Check the configuration of the dryer and make sure the settings are correct.
- Page 10 Doc #: 10000036988 Ver A 3.7.2 Connect the Tubing to the System Connect the other end of the tubing to the site distribution system or to the inlets to be pressurized. Different products and systems may use different connection methods. Four gas inlet/pipe adapters are supplied with the dryer.
- Page 11 Doc #: 10000036988 Ver A 3.8 System Purging It is important to properly purge the site distribution system prior to completing the dehydrator installation. Failure to do so may result in moisture being present in the system after the dehydrator is installed.
Need help?
Do you have a question about the RFS Technologies KD-C70 Series and is the answer not in the manual?
Questions and answers