Manufacturer's Recommendation - Intex CHALLENGER 3 Owner's Manual

(98PO) "NMMA" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 4.875" X 7.25" 05/14/2020

Manufacturer's Recommendation

The total number of persons, motor power and total weight shall not exceed the limits printed on
the boat. Please refer to the boat's hull label for the actual values of your boat. See Table A.
MODEL
CHALLENGER 3 / SET
SEAHAWK 2 / SET
SEAHAWK 3 / SET
SEAHAWK 4 / SET
EXCURSION 4 / SET
EXCURSION 5 / SET
MARINER 3 / SET
MARINER 4 / SET
REALTREE SEAHAWK 2 / SET
ISO 6185 PART 1 TYPE
CATEGORY D
1
Do not overinflate or use high pressure air compressor to inflate.
Adults should inflate the chambers with cold air in numbered
sequence.
Use the enclosed ruler to check while inflating.
Nicht zu stark aufblasen und keinen Kompressor zum Aufblasen
verwenden.
Erwachsene sollten die kammern in der angegebenen
Reihenfolge mit kalter luft aufblasen.
Verwenden Sie das beigefügte Lineal um die korrekte Füllung zu
überprüfen.
Ne pas surgonfler. Ne pas utiliser de compresseur pour le go flage.
Le gonflage doit être effectué par un adulte avec de l'air froid en
suivant les étapes suivantes.
Utiliser la règle jointe pour ajuster le gonglage de la chambre à
air principale.
2
PERSONS OR ____kg (___Lbs) / PERSONNES OU ___KG
____ POUNDS, PERSONS, GEAR / ___KG, PERSONNES ET ÉQUIPEMENT
DESIGN COMPLIANCE WITH NMMA REQUIREMENTS BELOW IS VERIFIED. MFGR. RESPONSIBLE FOR PRODUCTION CONTROL
LA CONFORMITÉ DU DESIGN AVEC LES EXIGENCES NMMA EST VÉRIFIÉE. MFGR. RESPONSABLE DU CONTRÔLE PRODUCTION.
Certified by the National Marine Manufacturers Association using ABYC standards
Certifié par la National Marine Manufacturers Association en utilisant les normes ABYC
CN- XEE
ISO-6185 boat design category (certain models).
1
Manufacturer's recommended maximum load capacity.
3
Maximum person's capacity.
5
Model name and number.
7
NMMA (for USA only) certification means that the boat, sold in the United States, has been judged by
9
the National Marine Manufacture's Association to be in compliance with the U.S. Coast Guard
Regulations and American Boat and Yacht Council (ABYC) standards and recommended practices.
Hull identification number (HIN).
10
SAVE THESE INSTRUCTIONS
TABLE A
B h
L h
TYPE
m m HP
II
1.37 1.5
2.95
II
1.14 1.5
2.36
II
1.37 1.5
2.95
II
1.45 1.5
3.51
II
1.65 1.5
3.15
II
1.68
3.66 1.5
II
1.27
2.97
II
1.45
3.28
II
1.14 1.5
2.36
BOAT LABEL FORMAT
MAXIMUM CAPACITIES
MAXIMUM-KAPAZITÃT
CAPACITÉS MAXIMUM
MAXIMUM POWER
MAXIMUM MOTORKRAFT
PUISSANCE MAXIMUM
PERSONS
PERSONEN
PERSONNES
MANUFACTURER
HERSTELLER
FABRICANT
MODEL
MODELL
MODÈLE
RECOMMANDÉ FONCTIONNEL PRESSION POUR CHAQUE CHAMBRE À AIR
BY INTEX ®
MAXIMUM CAPACITIES / CAPACITÉS MAXIMALES
LOAD CAPACITY (BASIC FLOTATION)
CAPACITÉ DE CHARGE (FLOTTAISON DE BASE)
Page 4
+ +
Lbs Kg
704 320 3
520 240 2
790 360 3
480 4
1050
4
1100 500
5
1320 600
3
2 880 400
3 1100 500 4
520 240 2
+
___kW (___HP) / ___Kg (___Lbs)
____________________
RECOMMENDED WORKING PRESSURE FOR EACH CHAMBER
EMPFOHLENE ARBEITENDE DRUCK FÜR JEDE LUFTKAMMER
= ___ bar ( ___ psi)
___Kg ( ___ Lbs) MAX.
CE mark (for Europe only) (certain models).
2
Maximum motor power and motor weight.
4
6 Manufacturer's name and country of origin.
Manufacturer's recommended working pressure.
8
Unladen Craft Weight
Kg
bar (psi)
0.035 (0.5)
9
0.069 (1.00)
6
0.069 (1.00)
11
0.069 (1.00)
17
0.069 (1.00)
19
0.069 (1.00)
22
0.080 (1.14) 25
0.080 (1.14)
32
0.069 (1.00)
6
+ = ___ Kg ( ___ Lbs)
= ___
CHINA
98
PO
3
4
5
6
7
8
9
10