Page 1
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 10/07/2011 INTEX ® OWNER’S MANUAL INFLATABLE BOAT IMPORTANT THIS BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. READ IT THOROUGHLY BEFORE USING THIS PRODUCT AND KEEP IT FOR FUTURE REFERENCE. ISO-6185 BOAT DESIGN CATEGORY D...
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 10/07/2011 TABLE OF CONTENTS INTRODUCTION..........................3 MANUFACTURE’S CERTIFICATION....................3 SAFETY & WARNING........................3 MANUFACTURER’S RECOMMENDATION..................4 DESCRIPTION..........................5-7 INFLATING INSTRUCTIONS......................8 HOW TO USE BOSTON VALVE.....................8 FISHING ROD HOLDER USE......................9 SEAT INSTALLATION ........................9 OAR ASSEMBLY........................9-10 GRAB LINE INSTALLATION......................11 ACCESSORY LINE INSTALLATION....................11 SAFETY AND OPERATION INSTRUCTIONS................11-12...
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 10/07/2011 Introduction This manual has been compiled to help you to operate your craft with safety and pleasure. It contains details of the craft, the equipment supplied or fitted, its systems, and information on its operation and maintenance.
Please refer to the boat's hull label for the actual values of your boat. See Table A. TABLE A Unladen Craft Weight MODEL TYPE bar (psi) 0.035 (0.5) 68369 1.37 CHALLENGER 3a 2.95 0.035 (0.5) 1.45 CHALLENGER 4a 68371 3.51 0.069 (1.00) 1.14...
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 10/07/2011 Description Challenger Series 8 10 Challenger 3a Challenger 4a " " - Recommended seating arrangement of the occupants. Seahawk Series Seahawk Seahawk 2 Seahawk 3 Seahawk 4 "...
Page 6
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 10/07/2011 Excursion Series 6 7 9 Excursion 2 Excursion 3 Excursion 4 Excursion 5 " " - Recommended seating arrangement of the occupants. Seahawk II " " - Recommended seating arrangement of the occupants. SAVE THESE INSTRUCTIONS Page 6...
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 10/07/2011 Mariner 4 " " - Recommended seating arrangement of the occupants. Descriptions Grab handle Inflation valve / Keel valve All around grab line Fishing rod holder Seat or seat cushion Motor mount Inflatable floor or removable slats floor Boston valve...
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 10/07/2011 Inflating Instructions Before starting, locate a clean area free of stones or other sharp objects. Unroll the boat so it is laid out flat, and locate your pump. Use a hand or foot operated air pump to inflate the boat.
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 10/07/2011 Fishing Rod Holder Use (Certain Models): 1. Slide the end cap over the end of the fishing rod. Fishing 2. Insert the fishing pole into the holder. End Cap Fishing Seat Installation: Holder...
Page 10
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 10/07/2011 FOR BOATS WITH ROTATION OAR-LOCK: Coupler Cover 10733 10734 Shaft B Shaft A Coupler Blade Retainer Ring FRENCH OARS: SAVE THESE INSTRUCTIONS Page 10...
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 10/07/2011 Grab Line Installation (Certain Models): IMPORTANT: To properly install the inflatable boat’s grab line and/or accessory lines, first inflate the boat. If is necessary, begin the grab line installation at the rear of the boat by threading it through the rope holders completely around the outside of the boat.
(98IO) "ISO" BOAT W / MOTOR MOUNTING (TYPE II) ENGLISH 7.5”X10.3” 10/07/2011 Rules to Observe During Navigation • Be responsible, do not neglect the safety rules, this could jeopardize your life and the lives of others. • Always keep control of your boat. •...
Through constant use you may occasionally puncture your boat. Most leaks only take a few minutes to repair. Your boat comes with a repair patch, and additional repair supplies can be ordered from Intex Consumer Service or from our website.
If a manufacturing defect is found within this 90-day period, please contact the appropriate Intex Service Center listed on the next page. If the item is returned as directed by the Intex Service Center, the Service Center will inspect the item and determine the validity of the claim. If the item is covered by the provisions of the warranty, the item will be repaired or replaced at no charge.
Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 •...
Need help?
Do you have a question about the CHALLENGER 3a and is the answer not in the manual?
Questions and answers