Advertisement

ASSEMBLY
GUIDE
LOHKO
FLEX 21 / FLEX 25 / FLEX 28
x4
12h
Versio 4/2023
TAIGA Product
Assembly Guides
& Videos
www.taigaconcept.fi/assembly

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LOHKO FLEX 21 and is the answer not in the manual?

Questions and answers

Summary of Contents for Taiga Concept LOHKO FLEX 21

  • Page 1 Versio 4/2023 ASSEMBLY GUIDE LOHKO FLEX 21 / FLEX 25 / FLEX 28 TAIGA Product Assembly Guides & Videos www.taigaconcept.fi/assembly...
  • Page 2: Installation

    Concept or Taiga Concept local dealers. will break easily. It is recommended to use Taiga Concept local When assembling the product make sure you Choosing location dealers authorized assembling person.
  • Page 3 If you find damage, document with photos according instructions Check if there is any damage Remove top cover and check that Carry the elements Assemble the product Activate product warranty to the package or pallet there are no signs of damage before www.taigaconcept.fi/activate Note: Take extra care unpacking.
  • Page 4 1. Take images where you can see 2. Take closer images of the damage 3. Contact your local Taiga dealer full package from 2 different angles which show the damage 1. Take images where you can see 3. Contact your local Taiga dealer 2.
  • Page 5: Elements & Components

    Elements & Components Hole Cover 12mm 21x 21x 21x T00744 Roof Connector 12x 14x 16x Mini x 15 48x 52x 60x T00368 T00184 Hole Cover 15mm 3x 3x T00398 Metal plinth C T00741 4x 4x 22x 22x 26x Window seal 2300 mm T00195 S200 mini x bolt T00185...
  • Page 6 Elements & Components 100cm Roof C 2x 3x Plinth D 1500 mm 2x 2x Power cable to slave unit 2x 2x T00179 T00737 EC224 6x 6x Glass A 693 mm width T00149 100cm 3x 3x 2x 2x 2x 2x Roof B T00180 Plinth E 1500 mm T00738...
  • Page 7 Equipments & tools 8x 8x 10x Plinth wire hole cap T00600 Gloves Safety glasses Safety shoes Safety helmet 4x 4x Expansion sealer tape T00648 5m x 20mm 1x 1x Foam tape T00192 50m x 30mm Screw machine + bits Hex key set Spirit leveler Glass suction cup Step ladder...
  • Page 8 ATTENTION Never put glass against hard surface, use always carton or carpet under the glass. Use always 2 person and suction cups to lift glass...
  • Page 9 T00190 Attach 3 mm thick foam under the metal plinth before installing the plinth together First add sides together and add foam under plinths and after that connect sides together...
  • Page 10 T00184 T00185 Check that cross measurements match then adding oor plinth in right order...
  • Page 11 T00194 T00194 Use long spirit leveler or laser to level the plinth...
  • Page 12 T00195 T00186 Add seal 2/3 of the length Add before sliding elements together T00146 When product comes close to wall clean glass before assembling...
  • Page 13 T00184...
  • Page 15 T00186 Add before sliding elements together T00146 T00195...
  • Page 16 T00184 Adjust the elements to be in same level Adjust level of plinth if there is gap between wall and plinth...
  • Page 17 T00181 Support the roof and place roof screws...
  • Page 20 T00181...
  • Page 22 T00399...
  • Page 24 T00147...
  • Page 25 T00191...
  • Page 26 T00187...
  • Page 27 T00124...
  • Page 28 T00186 T00146 T00146 T00186...
  • Page 30 T00146...
  • Page 31 T00146...
  • Page 32 T00146...
  • Page 33 T00194...
  • Page 37 T00194...
  • Page 39 T00194...
  • Page 40 T00368...
  • Page 41 T00181...
  • Page 43 T00187 T00187 T00191...
  • Page 45 T00181...
  • Page 46 T00187 T00187...
  • Page 47 Connecting cable...
  • Page 48 T00181...
  • Page 49 T00187...
  • Page 51 Connecting cable T00181...
  • Page 52 T00187...
  • Page 55 T00187 T00187...
  • Page 68 Activate product warranty www.taigaconcept.fi/activate...

This manual is also suitable for:

Lohko flex 25Lohko flex 28

Table of Contents