Related Manuals for Taiga Concept LOHKO PICEA 3
Summary of Contents for Taiga Concept LOHKO PICEA 3
- Page 1 Versio 2/2023 ASSEMBLY GUIDE LOHKO PICEA 3 TAIGA Product Assembly Guides & Videos www.taigaconcept.fi/assembly...
-
Page 2: Installation
Concept or Taiga Concept local dealers. will break easily. It is recommended to use Taiga Concept local When assembling the product make sure you Choosing location dealers authorized assembling person. - Page 3 If you find damage, document with photos according instructions Check if there is any damage Remove top cover and check that Carry the elements Assemble the product Activate product warranty to the package or pallet there are no signs of damage before www.taigaconcept.fi/activate Note: Take extra care unpacking.
- Page 4 1. Take images where you can see 2. Take closer images of the damage 3. Contact your local Taiga dealer full package from 2 different angles which show the damage 1. Take images where you can see 3. Contact your local Taiga dealer 2.
- Page 5 Elements & Equipments Components & tools 3x16 Countersunk screw T00091 Roof Connector T00368 4,5x30 Pan head screw T00124 Window seal 790 mm T00502 Hinge T00224 Gloves Safety glasses Safety shoes Safety helmet Window seal 1680 mm T00503 4,5 x 30 Hinge screw T00090 Door knob T00020...
- Page 6 Elements & Components Door Frame B T00484 Floor A T00481 Glass door T00059 Door Frame A T00051 Floor B T00482 Glass A 788 mm width T00490 Door Frame C T00483 Acoustic panel C 808 mm T00489 Glass B T00492 Door Frame D T00485 Acoustic panel B T00488...
- Page 7 ATTENTION Never put glass against hard surface, use always carton or carpet under the glass. Use always 2 person and suction cups to lift glass page 7 of 49 pages...
- Page 8 T00194 page 8 of 49 pages...
- Page 9 T00194 T00092 page 9 of 49 pages...
- Page 10 T00477 page 10 of 49 pages...
- Page 11 T00490 T00028 T00062 If back glass is close to a wall, clean it before placing page 11 of 49 pages...
- Page 12 T00478 page 12 of 49 pages...
- Page 13 T00028 T00490 If back glass is close to a wall, clean it before placing page 13 of 49 pages...
- Page 14 T00473 page 14 of 49 pages...
- Page 15 page 15 of 49 pages...
- Page 16 If power is supplied from floor level, connect supply cable (EC1xx to the connector inside the wall before installing the wall T00475 In case power is supplied from the ceiling, check page 46 Cable for table is routed through the groove inside the booth page 16 of 49 pages...
- Page 17 T00476 page 17 of 49 pages...
- Page 18 Make sure the walls lines perfectly on top and that there is no gap at the bottom of the wall and oor joint T00186 T00184 page 18 of 49 pages...
- Page 19 T00194 Before placing wooden pins make sure that there is no wooden dust in holes. page 19 of 49 pages...
- Page 20 T00480 page 20 of 49 pages...
- Page 21 T00054 5 mm Push the roof element 5mm to back page 21 of 49 pages...
- Page 22 T00479 page 22 of 49 pages...
- Page 23 Push roof elements together page 23 of 49 pages...
- Page 24 page 24 of 49 pages...
- Page 25 T00503 page 25 of 49 pages...
- Page 26 EP109 this side pointing up Assemble CO2 sensor page 26 of 49 pages...
- Page 27 T00124 If carpet is oversized from three side and need to be cut to meet the edges. T00486 When installing the carpet, T00485 use tape on the center T00090 and the edges page 27 of 49 pages...
- Page 28 T00489 T00488 If necessary remove oor door frame before assembling acoustic panel page 28 of 49 pages...
- Page 29 T00487 T00488 page 29 of 49 pages...
- Page 30 page 30 of 49 pages...
- Page 31 T00483 T00124 Route the cable through the groove and hole T00484 Check that there is no gap between wall element and door frame page 31 of 49 pages...
- Page 32 T00492 page 32 of 49 pages...
- Page 33 CD005 page 33 of 49 pages...
- Page 34 ~2 mm SS004 ~2 mm page 34 of 49 pages...
- Page 35 T00015 Remove the tape cover and push frame againt the glass page 35 of 49 pages...
- Page 36 Doorframe 91 cm Glass page 36 of 49 pages...
- Page 37 Magnets on the control panel connect to the screwheads EP106 Plug and test electricity See page 47 option 1 or 2 page 37 of 49 pages...
- Page 38 T00090 > 20 ° Use three washers rst and add or remove if needed to adjust the door. page 38 of 49 pages...
- Page 39 If the door glass is curved, use it as shown on the left picture above. Attention, check whether the door is straight before assembling. To get door closed properly, add more magnets to the top and bottom If the door is curved, assemble it as guided on the right image. part of the door frame if necessary.
- Page 40 T00059 Clean around these areas and dry before assembling hinges Never put glass against a hard surface, always use carton or carpet under the glass. Always use 2 persons and the suction cups to lift glass page 40 of 49 pages...
- Page 41 Torque = 20 Nm Tighten screws very tight by hand using Hex key BOTTOM BOTTOM Make sure the top corner glass does not go over the hinge. Never use drilling machine to tighten hinge screws This will protect the glass from the metal part to hit when swinging. page 41 of 49 pages...
- Page 42 page 42 of 49 pages...
- Page 43 Make sure the up corner does not damage the elements > 20 ° Make sure that door glass will not touch hinge support parts while and after assembling the door page 43 of 49 pages...
- Page 44 Warning! Make sure the screws don’t damage the glass T00090 T00090 > 130 ° page 44 of 49 pages...
- Page 45 SM001 To increase magnetic strength add small magnets to metallic strip (no screws required) page 45 of 49 pages...
- Page 46 ~6 mm ~3 mm T00024 T00020 ~3 mm ~6 mm page 46 of 49 pages...
- Page 47 Clean all surfaces Make sure that any water used in the cleaning process will not leak between the elements and glass. Turn on the ventilation, check each side and corner of the door by hand that there is no air leaks Check if there is any air leak between frames and elements/glasses.
- Page 48 Option 2: Powercord assembled from roof level page 48 of 49 pages...
- Page 49 Activate product warranty www.taigaconcept.fi/activate page 49 of 49 pages...