Page 1
Owner's Manual Please read this manual thoroughly before operating the 280X training e-collar.
Page 2
Unauthorized use Children and the disabled Dogtra products should only be used in a humane manner to Dogtra products are not toys. Adult supervision and extreme train and educate dogs. caution are required when Dogtra products are used by or Dogtra products are not intended for use in any other way near children.
CONTENTS BATTERY CHARGE ..........AT A GLANCE ............... ATTACHING THE BELT CLIP ........ MAIN FEATURES ............OVERVIEW ..............USING THE TEST LIGHT ........GENERAL TRAINING TIPS ......... UNDERSTANDING YOUR TRAINING SYSTEM MAINTENANCE ............. TURNING THE PRODUCT ON/OFF ....TROUBLESHOOTING GUIDE ........DEFAULT BUTTON SETTINGS ......
Optional Accessories • 2-hour rapid charge batteries for transmitter and Auto Charger receiver The input of the automatic charger for 280X is 12V ~ 24V and the output is 5V 1000mA. • USB C-TYPE Charging European Charger Dogtra's European chargers are designed for use with 220V AC electrical outlets.
UNDERSTANDING YOUR 2. DEFAULT BUTTON SETTINGS TRAINING SYSTEM Front button (Nick or Constant) The front button can be selected as Nick/Constant. The HOW TO USE THE TRANSMITTER stimulation type indicated at the top of the display is applied. (Factory set to Nick mode) 1.
3. SIDE BUTTONS Applies Displayed Base Level. Press Press In this case, level 5 Boosted Tone Constant ‘Nick’ will apply. Locate Light XPP Vibration Boosted Constant Applies ‘Boosted Constant’ Apply Constant boost stimulation for up to 12 seconds at Press Press for up to 12 seconds.
Page 8
Setting up Boost feature Non-Stimulation Features 1. Set the stimulation level XPP (Extreme Performance Pager) to zero. Vibration Rheostat Provides vibration for up to 12 Dial seconds when held. LCD Screen Tone Provides an audible tone for up to 12 seconds when held.
4. SAFETY LEVEL LOCK 6. HOW TO ADD AN ADDITIONAL RECEIVER DEVICE Stimulation level lock indicator 1. Turn on the transmitter and set the stimulation level to “0”. Use the toggle to select the desired dog (1,2 or 3). To prevent the stimulation level from changing unintentionally, press and hold the top of the Rheostat dial for more than 2 seconds to lock it.
7. X-SHIELD INSTALLATION 8. HANDSFREE/PLUS SQUARES PAIRING Additional X-SERIES case covers, X-Shields are sold Select the number Dog separately. you want to pair with the HANDSFREE SQUARE Pairing light indicator HANDSFREE SQUARE PAIRING: NICK OR CONSTANT NICK OR CONSTANT 1. Use the included tool to 2.
Page 11
HANDSFREE SQUARE Pairing: LIGHT Hold down the on/off All other Functions button and the Light 1. Begin with the remote transmitter turned off. button. 2. Press and hold the ON/OFF button + your desired Light Button function until you see the rapid light blink. 3.
1. Insert the strap by looking at the direction of the arrow corrections to be inconsistent. Dogtra uses medical grade on the receiver. stainless steel contact points and anti-microbial plastic to protect the dog’s skin.
The range is reduced when the handheld transmitter's antenna is covered or in contact with your body. Refer to The operating range of the 280X is ½ mile. the following carrying methods for optimal range. Depending on how you use the transmitter, the range of your transmitter may vary.
5. NON-STIMULATION CONTACTS 1. Please turn the contact points and remove them. The 280X has a rheostat dial on the top of the transmitter. Always start at the lowest level and work your way up. 2. Place non-stimulation contacts in each place You will find the right level when your dog responds to the stimulus with a mild response.
6. LED INDICATOR 7. CARE FOR LCD TRANSMITTERS IN COLD TEMPERATURE The LED indicator flashes every 4 seconds when the In cold temperatures (below 10°F), the transmitter's liquid receiver is on and ready for use. The LED indicator will crystal display (LCD) may appear dim or unresponsive. blink on both the transmitter and the receiver when the Wait until you see the display before selecting your transmitter buttons are pressed.
4. After charging, cover the battery charging socket with a Dogtra 280X uses a lithium polymer battery. If the light is rubber plug. red, the device does not turn on, or the system does not Recharging is required in the following cases: stay on when you press the button, recharge the device.
10. USING THE TEST LIGHT 9. ATTACHING THE BELT CLIP To attach the included belt clip, follow the instructions 1. Turn on the receiver by pressing and holding the on/ below. off button in the center of the contact terminal. The 1.
Your dog must know some basic obedience commands 6. Turn the rheostat dial on the transmitter clockwise and before beginning training with the 280X. A dog learns then counterclockwise. The test light shines brighter at by first being shown a command, followed by lots of higher stimulus levels and dimmer at lower levels.
Troubleshooting If the unit is malfunctioning, please refer to the “Troubleshooting Guide” before sending it to Dogtra for service. If you have any questions or concerns, you may email them to Info@dogtra.com, or call customer service...
(response may be very subtle so pay – If the above does not resolve your issues, contact attention.) Dogtra customer service at info@dogtra.com or (888) 811-9111. 2. The LED indicator light comes on, but I do not feel any stimulation.
(“Warranty”). The Warranty covers the cost of repair (parts PART 15.21 and labor) or replacement (if repair is not feasible) of a defective Dogtra Any changes or modifications (including the antennas) to this device product during said one-year period. For such repaired or replaced that are not expressly approved by the manufacturer may void the user’s...
Page 22
No dealer of Dogtra products, nor any employee or agent of visit www.dogtra.com/product-registration. If your product is not registered with Dogtra, You will be required to provide a receipt or other Dogtra, is authorized to make any additions, changes, or extensions to the Warranty.
Need help?
Do you have a question about the 280X and is the answer not in the manual?
Questions and answers