Subscribe to Our Youtube Channel
Related Manuals for Dogtra 2700T&B
Summary of Contents for Dogtra 2700T&B
- Page 1 2700T&B 1-DOG SYSTEM ONLY Owner's Manual Please read this manual thoroughly before operating the Dogtra 2700T&B Training & Beeper Collar.
- Page 2 Consult your physician or Dogtra product or other property. medical device maker before using your medical device with a Dogtra product. If you think that your Dogtra PRODUCT SAFETY product is interfering with your pacemaker, defibrillator, Training Methods or other medical device, stop using the Dogtra product.
-
Page 3: Table Of Contents
FAMILIARIZING THE DOG TO THE BEEPER ..MAXIMIZING THE DISTANCE ........ Optional Accessories LED INDICATOR ............Auto Charger Dogtra’s auto chargers are designed for use with a CHARGING THE BATTERY ........10 volt car outlet. HANDHELD TRANSMITTER LCD ......European Charger ATTACHING THE BELT CLIP ........ -
Page 4: Main Features
MAIN FEATURES • One-charging system allows the transmitter and receiver(s) to be charged at the same time • Easy-to-use, ergonomically fitted transmitter • Easily visible blue LCD screen displays the exact level • Rheostat Dial that allows for gradual adjustments in of stimulation that can be seen in the dark stimulation intensity with no jumps between levels •... -
Page 5: Overview
OVERVIEW Antenna Rheostat Dial Collar Strap Contact Points Indicator Battery Charging Light Receptacle and Rubber Plug Beeper Pitch Toggle Switch Locate On/Off Button & Nick Mode Pager Constant Belt Clip Screen LED Indicator Light On/Off Magnetic Switch On/Off Magnetic (Red Dot) Red Dot Battery Charging Receptacle &... -
Page 6: Understanding Your Training System
UNDERSTANDING YOUR Receiver On/Off Magnetic Red Dot To turn on the receiver/collar, place the magnetic red TRAINING SYSTEM dot on the back of the transmitter to the red dot on the receiver/collar. Hold the two red dots together for a 1. -
Page 7: Transmitter Button Function
2. Transmitter Button Function Locate Button The Locate button is located on the left side. It causes 2700T&B the collar’s beeper horn to emit a series of beeps when held down and gives you the ability to keep track of your Beeper Pitch Locate dog’s location. -
Page 8: Beeper Sound
3. Beeper Sound 4. Beeper Volume Adjustment When you press the Mode button the first time, the collar The beeper volume level for the Run/Point mode and will beep twice. The beeper unit will always start in Run/ Point-Only mode can be increased or decreased by Point mode. -
Page 9: Collar Fitting
If the collar is too loose, the contact will not be consistent and cause when the stimulation is in use. the corrections to be inconsistent. Dogtra uses surgical stainless steel contact points and anti-microbial plastic 7. Familiarizing the Dog to the Beeper to protect the dog’s skin. -
Page 10: Maximizing The Distance
9. LED Indicator 8. Maximizing the Distance The 2700T&B collar has a range of 1 mile. Depending on The LED indicator flashes every 4 seconds when the the way you use your transmitter, the transmitter range receiver is on and ready for use. The LED indicator will may vary. -
Page 11: Charging The Battery
Note 2: The unit has a partial charge when it leaves the Constant button is pushed. Dogtra facility. Upon receipt of the collar, be sure to give it a full 2-hour initial charge before the first use. When a charger is not in use, disconnect it from the power source. -
Page 12: Handheld Transmitter Lcd
11. Handheld Transmitter LCD the auto charger, plug into a cigarette lighter only for lithium polymer batteries (use a 230 volt European charger for Europe). All indicator lights should glow red when properly plugged in and the unit will automatically shut off during the charging process. You will need to turn the unit on again before use once the unit is fully charged and unplugged from the battery cable. -
Page 13: Attaching The Belt Clip
the intensity level to freeze at that current level. In this 12. Attaching the Belt Clip situation, if you turn the Rheostat Dial, the level on the screen may not change but the actual intensity from the receiver/collar will change in agreement with the dial. In this situation, it is ideal to either wait until your transmitter is back to working order before emitting a correction, or while holding the Constant button down... -
Page 14: Using The Test Light
13. Using the Test Light 4. Watch the test light as you push the Nick button on the transmitter. It should light up for just a moment. The higher the intensity, the brighter the test light will 5. Watch the test light as you push the Constant button on the transmitter. -
Page 15: General Training Tips
GENERAL TRAINING TIPS 9. Press the Mode button a second time; you should hear 1 rapid beep. This will put you into the Point-Only Getting Started With Your 2700T&B mode. Once again, keep your receiver/collar steady Your dog must know some basic obedience commands and wait for a moment until the collar emits a double before beginning training with the 2700T&B. -
Page 16: Maintenance
For more training information, please visit our website at If the unit is malfunctioning, please refer to the www.dogtra.com. “Troubleshooting Guide” before sending it to Dogtra for service. If you have any questions or concerns, you may email them to info@dogtra.com, or call customer service... -
Page 17: Troubleshooting Guide
(response may be very subtle). at info@dogtra.com or (888) 811-9111. You can send in 2. The test light comes on, but I do not feel any your charging units to have us inspect them. - Page 18 No dealer of Dogtra products, nor any employee or agent of Dogtra, is authorized to make any additions, changes, or extensions to the Warranty. Dogtra, at its sole discretion and at any time, reserves the right to modify the Warranty.
- Page 19 Dogtra’s liability is limited to the cost of repair or replacement of the Dogtra fees, for products sent to Canada. Such costs, taxes, or fees will be borne by product under Warranty.
Need help?
Do you have a question about the 2700T&B and is the answer not in the manual?
Questions and answers