LockMasters LockOne LKM10K Installation Instructions Manual
Exit only push pull handle
Hide thumbs
Also See for LockOne LKM10K:
- Operating instructions (2 pages) ,
- Installation instructions manual (16 pages)
Subscribe to Our Youtube Channel
Related Manuals for LockMasters LockOne LKM10K
Summary of Contents for LockMasters LockOne LKM10K
- Page 1 Not FF-L-2890B Approved Exit Only Model EXIT ONLY Push Pull Handle Model Installation Instructions In A Single Motion, We’ll Change The Way You Think About Security. Model: Exit Only Push/Pull Handle...
-
Page 2: Important Safety Notes
LKM10K EXIT Only Push Pull Handle Model Installation The LKM10K is the second generation of pedestrian door lock devices produced by Lockmasters IMPORTANT SAFETY NOTES Inc. It was designed from the ground up to meet the needs to secure Sensitive Compartmented Please read the instructions carefully. - Page 3 Limited Liability Product Warranty Information Lockmasters, Inc. warrants to the original retail purchaser for a period of two (2) year from the purchase date of the product that the product shall be free of defects in the materials and workmanship, provided there is compliance with all installation, operating and maintenance instructions provided by Lockmasters, Inc.
- Page 4 Base Plate Cover - Small Base Plate Cover - Large Change Key Plug Exterior Trim Plate Base Plate - A Base Plate Cover - C Base Plate Cover - B Change Key Plug - D LKM10KHEINST © Lockmasters, Inc. 2018 February 2018 Version A...
-
Page 5: Tools Needed
LKM10K Push Pull Handle Model Exit Only Base Plate Mounting Template - RightHand REV. E Part Number: 10KRHEOTMP Masking Tape Sharpie or Pencil 1/4 Philips Bit Philips Screwdriver Flat Scresdriver Wire Strippers LKM10KHEINST © Lockmasters, Inc. 2018 February 2018 Version A... - Page 6 Exterior Trim side of the door with the combination square at least 10”. 2b- Extend Horizontal line to door’s edge 2c- Continue Horizontal line to Exterior Trim side at least 10” across the door. LKM10KHEINST © Lockmasters, Inc. 2018 February 2018 Version A...
- Page 7 You will see a gap between the door and combination square. (See Figure 2) Figure 2 - Establishing the high side of a bevel edged door. LKM10KHEINST © Lockmasters, Inc. 2018 February 2018 Version A...
- Page 8 (See large red circle in figure 5) "B" "B" 7/16” 7/16” 8 " LOCKMASTERS, INC. LKM10K Exit Only Exterior Trim Mounting Template Part Number: 10KEEOTMP Figure 4 - Sample Template REV E LKM10KHEINST © Lockmasters, Inc. 2018 February 2018 Version A...
- Page 9 When drilling a hollow metal door you need to use a metal cutting hole saw. 7 - Pilot drill all holes with a 3/16” bit LKM10KHEINST © Lockmasters, Inc. 2018 February 2018 Version A...
-
Page 10: Drilling The Holes
10b – WOOD DOOR pre-thread the 2 (C) Base Plate attaching holes using one of the Phillips head thread forming screws (R). A #2 square drive bit works well with the screws 10a - Debur all LKM10KHEINST © Lockmasters, Inc. 2018 February 2018 Version A... - Page 11 12a - Remove ALL (8) flat head back cover 12b - Slide the smaller “nose cone” cover off first. screws. 12b - Remove the larger portion of the cover off 12 - Base Plate with both covers removed second. LKM10KHEINST © Lockmasters, Inc. 2018 February 2018 Version A...
- Page 12 13d & e - With pressure on wrench tighten screw screw and remove the wrench. 13g - Repeat steps 13a - 13f on the remaining C2 hole. 13f - Jack Nut firmly seated, screw removed LKM10KHEINST © Lockmasters, Inc. 2018 February 2018 Version A...
- Page 13 (4) upper B holes. 15c - Insert the (4) 1/4”-20x1-1/8” screws and Exterior Trim Attached through the Base Plate split washers into the (4) B holes. LKM10KHEINST © Lockmasters, Inc. 2018 February 2018 Version A...
- Page 14 Plate handle depending on the swing of the door. 17a - Clean the handle with rubbing alcohol 17b - Place the correct Pull or Push label on the Base Plate Handle LKM10KHEINST © Lockmasters, Inc. 2018 February 2018 Version A...
- Page 15 18h - Drill Pilot Holes in the remaining (3) strike 18i & j - Apply Thread Locker to strike screws and holes and tap. attach strike. Remove the (2) previously installed screws, apply Thread Locker and re-install LKM10KHEINST © Lockmasters, Inc. 2018 February 2018 Version A...
Need help?
Do you have a question about the LockOne LKM10K and is the answer not in the manual?
Questions and answers