Do you have a question about the LFU-45IT and is the answer not in the manual?
Questions and answers
Alexandra Gillies
April 6, 2025
I have a Fagor LFU-45IT - if I put the machine onto the 30min 35C programme (2) it gets stuck on the washing cycle. I have to stop it manually by opening door and pressing start/pause then turning power off. Any guidance very welcome. Thanks in advance.
Page 1
Description of the controls________________________________28 Troubleshooting _______________________________________36 Thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need about the right conditions for the proper, safe use of your dishwasher.
EXTRA PROGRAM LIGHT Illuminates to indicate that one of the five extra programs (see table) is going to be executed. PROGRAM DELAY BUTTON Press this button to delay the start of the program by up to 9 hours. INFORMATION DISPLAY...
Page 3
User instructions SETTING THE WASHING PROGRAM AND SWITCHING ON To select the most suitable program for the dishes to be washed refer to the table below, which indicates the most appropriate program according to dish type and degree of soiling.
Page 4
(2) The cycle duration and power consumption may vary according to the water and room temperatures, and the type and amount of dishes. The washing cycle will not take place if the dishwasher door is left open or not properly closed.
"main" program (1, 2, 3, 4 or 5). This function is retained in the memory, so the button has to be pressed again (the light goes out) if the user wishes to execute one of the 5 main programs at the next cycle.
The PROGRAM DELAY button (8) can be pressed to delay the start of the program by up to 9 hours. This means that the dishwasher can be operated at the time of day of your choice. Press the button several times in succession and the display will show the delay with which the appliance will start, beginning from 9 hours.
Page 7
• do not pour the detergent directly on the dishes. If the door has to be opened while washing is in progress, the program will be interrupted. The relative light will keep flashing and a beeper will signal that the cycle has not been completed. You must wait about 1 minute before closing the door to restart the program.
User instructions ADJUSTING THE WATER SOFTENING SYSTEM N.B.: for the setting below to be possible, a washing program other than the soak program must be set. Press the PROGRAM DELAY button (8) and keep it pressed until the preset value appears followed by a full stop (normally 3.).
END OF CYCLE At the end of the program the beeper sounds briefly and the lights of programs 4 and 5 flash (the word "end" is displayed on the window). 45° 55° 65° 70° To switch off the dishwasher, open the door and press the ON/OFF button (1).
2. Troubleshooting The dishwasher is capable of signalling a number of faults through the simultaneous illumination of several indicator lights, with the following meanings: FAULT DESCRIPTION Acquastop failure The anti-flooding system has been activated (for the relevant models only). The system is tripped in case 45°...
Page 11
To “reset” an alarm is necessary: • Open and close the door, or turn off and on the machine. At this point is possible to program the dishwasher again. If the malfunction persists, contact your authorised Service Centre.
Page 12
: gemäß denModellen 820÷870 oder 820÷890. LET OP: Hoogte "H" : voor de modellen 820÷870 of 820÷890. ATENCIÓN: Cota "H" : según los modelos 820 ÷ 870 o bien 820 ÷ 890. ATENÇÃO: Cota "H" :dependendodos modelos 820-870 ou 820-890. 1/2” 3/4” 3/4”...
Need help?
Do you have a question about the LFU-45IT and is the answer not in the manual?
Questions and answers
I have a Fagor LFU-45IT - if I put the machine onto the 30min 35C programme (2) it gets stuck on the washing cycle. I have to stop it manually by opening door and pressing start/pause then turning power off. Any guidance very welcome. Thanks in advance.