Related Manuals for Maxtor MTC07 Series
Summary of Contents for Maxtor MTC07 Series
- Page 1 INSTALLATION MANUAL MTC07 series We reserves the right to improve the product's appearance, size and technology without prior notice. All products sizes and colors are subject to the actual product...
-
Page 2: Installation
Preparation before installation PRECAUTIONS All vanities must be installed by a fully qualified plumber. Vanities and tops must be installed onto finished surfaces. It is imperative that all bathroom installations are ventilated to meet standards. Failure to provide ventilation that meets these standards will void the manufacturer's warranty. - Page 3 Product size chart MTC07060 VANITY SIDE MT01060S MWC07060 MTC07070 VANITY SIDE MT01070S MWC07070 MTC07080 VANITY SIDE MT01080S MWC07080...
- Page 4 MTC07100 VANITY SIDE MT01100S MWC07100 MTC07120 VANITY SIDE MT01120S MWC07120 MTC07120 VANITY SIDE MT01120S MWC07120...
- Page 5 Installation of different walls WOODEN WALL PREPARATION Make sure the vanity and LED mirror (or Medicine cabinet) be mounted on the reinforcement plate. 2"x4" [50x100mm] Wood Reinforcement 38'' [960mm] Wood Reinforcement 2"x8" [50x200mm] Wood Reinforcement 33-1/2'' [850mm] Suggested Helght SOLID WALL...
-
Page 6: Cabinet Installation
Specication & Installation Guide Recommended Wall VanityMounting Height 13-3/4'' [350mm] 34-1/4'' [870mm] IMPORTANT! Make sure that the reinforcemente holds your bathroom cabinet securely before installing it. CABINET INSTALLATION STEP 1 Locate cabinet & mark location 33-1/2'' [850mm] Suggested Helght... - Page 7 STEP 2 STEP 3 Wall positioning perforation & Wall plug Tighten the screws Φ10mm Drill Bit M6 PA screws 31-1/4'' [795mm] Suggested Helght STEP 4 STEP 5 The installation of the basin...
-
Page 8: Electric Connections
ELECTRIC CONNECTIONS ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENCED ELECTRICIAN WARNING: Shut off power before wiring the mirror. WARNING: An Electrical option mirror must be wired to a 20 Amp GFl(Ground Fault Interrupter) protected circuit when used in bathrooms andall other locations required by the National Electric Code. - Page 9 MIRROR MOUNT STEP 1 STEP 2 Placment Support location Select the desired position of the mirror. Measure the center of the holes and mark the Level and mark the location. drilling locations ensure marking are leveled. 13-3/4'' [350mm] STEP 3 STEP 4 Install screws Placement...
-
Page 10: Faucet Installation
FAUCET INSTALLATION For first time install, flush the pipes first byopen the angel valve to run 60s. STEP 1 STEP 2 Clean and wipe the countertop and check Remove the mounting hardware from if it is level. themounting pipe. STEP 3 STEP 4 Put the rubber O-ring into the bottom gap Slide rubber washer,metal washer and... - Page 11 POP-UP WASTE INSTALLATION STEP 1 lnstall Pop-up Waste with over flow STEP 2 Connect the drain pipe...
-
Page 12: Drawer Assembly
DRAWER ASSEMBLY Lay the drawer bottom onto the slide then push thedrawer into the cabinet. Removal with Locking Device For removal, hold the handle and pull out the drawer. Drawer up & down adjustment:0~+3mm. - Page 13 HINGE ADJUSTMENT AND REMOVAL INSTRUCTION PIVOT-PRO side adjustment Side adjustment of the door is made by using the indicated screw. PIVOT-PRO Depth Adjustment Depth adjustment is made without loosening any screw.The door can be moved in or outby rotating the cam adjuster on the hinge arm. Snap-on cam-adjustable PIVOT-PRO Height Adjustment...
-
Page 14: Door Remove
DOOR INSTALL DOOR REMOVE... -
Page 15: Troubleshooting
TROUBLE SHOOTING What happens if my soft close drawer is not closing properly? It means that your soft close drawer is not engaged correctly. Follow the instructions on page 03 to re-engage the soft close mechanism. Why is my soft close drawer making a noise on closing, and not closing smoothly? If the release tabs on the drawer are not lifted properly, then this may cause the cog to strip on the soft close mechanism. -
Page 16: General Cleaning
Cleaning and Warranty General Cleaning Aquas Bath products are made from materials or sourced specifically for bathroom and laundry spaces. Our vanities and cabinetry are designed to be water resistant, not waterproof. Care must be taken to immediately dry spillage as well as ventilate your bathroom to eliminate moisture build up or humidity which will lead to deterioration of materials and is not covered by warranty.
Need help?
Do you have a question about the MTC07 Series and is the answer not in the manual?
Questions and answers